Eaton Sure-Lites UX6 User manual

IB505040EN 049-286
Installation Instructions for the Sure-Lites UX6 AC only Exit Sign. UX6 Exit Signs
and Markers for Use in HAZARDOUS LOCATIONS
WARNING
Risk of Fire/Electric Shock
If not qualified, consult an electrician.
WARNING
Risk of Electric Shock
Disconnect power at fuse or circuit breaker before
installing or servicing.
Important Safeguards
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING
THE FOLLOWING.
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Do not use near gas or electric heaters.
3. Do not use this equipment for other than the intended use.
4. Installation is to be performed only by qualified personnel.
5. Install in accordance with National Electric Code and local
regulatory agency requirements.
6. The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
7. Equipment should be mounted in locations and at heights
where it will not readily be subjected to tampering by
unauthorized personnel.
8. SAVE THESE INSTRUCTIONS
Sure-Lites
INSTALLATION – HAZARDOUS LOCATIONS
NOTE: Wall or ceiling mounting using the canopy kit is not
intended for hazardous locations. The canopy kit is not
suitable for Hazardous Locations and is meant Non-
Hazardous Locations installation only.
NOTE: For hazardous location compliance, the UX must be
installed using the provided conduit hub. The UX should
not be directly mounted to a junction box when used in
hazardous locations.
1. For field supply connection to the unit, use suitable wiring
method for the hazardous location per NEC. Circuit should
not be energized at this time.
2. Remove the weather shield by removing the 4 screws in
the corners (See Figure 1). Due to the airtight nature of the
exit sign, the weather shield may be held on by a slight
vacuum. If this occurs, carefully pry the corners of the
shield with a flat head screwdriver, but do no damage the
water shield or inner gasket.
3. Remove the stencil face by prying the snap fits on the side
up, by placing a flat head screw driver in the slots and
lifting (See Figure 1).
4. Choose the appropriate knock out for the mounting (left
side, right side, or top or backplate), and knock it out using
a hammer and flat blade screwdriver. Connect conduit
using the ½” fitting provided (See Figure 4).
5. For single face units only, if needed, knock out the two
round knock outs at the far left and right of the backplate,
and apply foam gasket to the back of the exit sign. Use
these holes to attach the UX to the wall using a standard
#8 screw or larger. Only remove the gasket holes needed
for installation. For double face units, proceed to Step 6.
NOTE: When mounting the UX, it is necessary to consider the
weight of the exit sign, about 7 pounds. A suitable anchor
is recommended, or mounting directly to a stud for the
junction box the exit sign is mounted to.
6. After the frame is securely mounted, the stencil can be
hung for “hands free” wiring using the Sure-Lites EZ Hang
system. (See figure 2).

2
IB505040EN
UX AC only Exit Sign Installation Instructions www.eaton.com/lighting
Figure 1
INSERT
SCREWDRIVER
HERETO
REMOVE STENCIL
INSERT
SCREWDRIVER
HERETO
REMOVE
STENCIL
2
Figure 2
SLOT
TAB
SLIDE SLOTS OVERTABSTO
TEMPORARILY HANG
FIXTURE FOR WIRING
Figure 3
WIRE
CONNECTIONS
ALLOWED IN
ENCLOSURE
AREAS
NO WIRE CONNECTIONS
ALLOWED IN SIGN FACE
WIRE
CONNECTIONS
ALLOWED IN
ENCLOSURE
AREAS
Figure 4
KNOCKOUT
(REMOVE
AS NEEDED)
WATER TIGHT
CONDUIT HUB
CONDUIT
HUB NUT
7. Connect power supply and ground in accordance with local
codes. Wire connections as follows: 277VAC line to Orange
lead or 120V line to Black lead; Neutral to white lead. Ground
to Green Screw on backplate (single face), frame (double
face) or conduit hub with integral terminal, if provided. Cap
unused line lead with wire nut provided (see Schematic).
Connections must be in the enclosure rated area of the
frame (See Figure 3), not in the sign face. Make sure wires
are routed so they do not create shadows on the face of the
exit.
8. Determine which color sign face is needed. If red is needed,
proceed to step 11.
9. If green is the desired color, remove the red lens from the
stencil by removing the white vinyl caps holding the lens in
place and replace it with the green lens provided. Replace
the white vinyl caps.
10.On the LED circuit board, locate the red/green jumper (See
Schematic).The jumper should be in the red position per the
silk screen printing on the board. Pull gently upward on the
jumper, then shift it one pin over to activate the green LEDS.
11. Replace the stencil cover assembly, and weather shield. To
insure a water tight fit, make sure the gasket and weather
shield edge are clean and free of debris.
12.Energize AC supply, LED display will come on.
NOTE: The foam gasket is suitable for smooth surfaces, but
for rough surface mounting, silicone caulk should be used to
prevent water from entering the exit sign.

3
Eaton
1121 Highway 74 South
Peachtree City, GA 30269
eaton.com/lighting
© 2016 Eaton
All Rights Reserved
Printed in USA
Publication No. IB505040EN
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
MAINTENANCE
NOTE: None required
NOTE: Servicing of any parts should be performed by qualified
personnel. Only use replacement parts supplied by Eaton.
TROUBLE SHOOTING GUIDE
If LED display does not illuminate, check the following:
1. Check AC supply – verify that unit has 24 hour AC supply.
2. Unit is shorted.
3. If following the above trouble shooting hints does not
solve your problem, contact your local Eaton Lighting
representative for assistance
WARRANTIES AND LIMITATION OF LIABILITY
Please refer to www.eaton.com/LightingWarrantyTerms for our
terms and conditions.
SCHEMATICS
SHIFT JUMPERTO UPPER
POSITIONTO LIGHT RED
LEDS. SHIFT JUMPERTO
LOWER POSITIONTO LIGHT
GREEN LEDS. FACTORY
SETTING IS RED.
POWER SUPPLY
PC BOARD
LED6
LED10
LED5
LED9
LED4
LED6
LED3LED2LED7LED1
CN1
POWER
RED GREEN
ORANGE LEAD -TO 277
WHITE LEAD -TO NEUTRAL
BLACK LEAD -TO 120V
CN2 POWER