Eaton 5S 850 User manual

Installation and
user manual
EATON 5S
850/1200/1600

2614-06819-00
2 3
1
5
EATO N 5S
Packaging
lBefore installing the Eaton 5S, read the booklet 3containing the safety instructions to be respected.
Then follow the instructions given in this manual 2.
Caution!

3
614-06819-00
Quick start
B
C
A
1200 / 1600
850
D

4614-06819-00
Battery change
•Warning: take care not to inverse the polarity + (red) and - (black) when connecting the batteries as this will
destroy the device.
a
b
c
d
a
b
c
d
850
1200 / 1600
Battery disposal and safety
•Caution. Battery service life is reduced by 50 % for every ten degrees above 25 °C.
•The battery elements must be replaced exclusively by qualied personnel (risk of electrocution), with new
elements approved by Eaton to ensure correct operation of the UPS.
•The battery must be disposed of in accordance with applicable regulations.To remove the battery elements, shut
down the UPS (button 6OFF), remove the power cord and proceed as indicated in page 4 "Battery change".

5
614-06819-00
Technical characteristics
(*) Warning: Output cables should not exceed 10m length.
Eaton 5S 850 1200 1600
•UPS power 850 VA /
510 W
120 VA /
750 W
1600 VA /
1000 W
•Nominal input voltage 185 V - 285 V, adjustable to 150 V - 285 V
•Input frequency 50/60 Hz (46 - 70 Hz working range)
•Voltage/frequency of battery backup
outlets 19 in battery mode
220 V / 230 V / 240 V +15 % -20 % (50/60 Hz ± 1 %)
•Total output current for all outlets 10 A max
•Output current of battery backup
outlets 19
3.8 A max 5.4 A max 7.3 A max
•Leakage current 0.4 mA
•Input protection 10 A resettable circuit breaker
•Transfer time 5 ms typical
•Telephone surge protection Tel, ISDN, ADSL, Ethernet
•Sealed lead-acid battery 12 V, 9 Ah 2 x 12 V, 7 Ah 2 x 12 V, 9 Ah
•Automatic battery test Once a week
•Average battery life 4 years typical, depending on temperature and amount of discharge cycles
•Operating temperature 0 to 35 °C
•Storage temperature -25 °C to +55 °C
•Operating relative humidity 0 to 85 %
•Operating elevation 0 to 2000 m
•Safety standards IEC62040-1,CEcertied
•Electromagnetic compatibility
standards
IEC 62040-2, C1*
AS 62040-2, C1
•Warranty 2 years
•Dimensions (mm) 263 x 81 x 235 305 x 81 x 312
•Weigth (Kg) 3.6 6.7 7. 8

6614-06819-00
1. Operating conditions
• This product is an Uninterruptible Power Supply (UPS) for computers and their
peripherals, television sets, stereo systems and video recorders... It must not be used
to supply other electrical equipment (lighting, heating, household appliances, etc.).
• UPS can be installed in horizontal, vertical position, or placed in Rack 2U (optional kit).
2. Description
AVR
%
Min
Hz
kVA
kW
6
7
8
6ON/OFF button for the
battery backup outlets
7Scroll down
8Mute alarm
LCD
16
15
14
17
11
10
912
13
9UPS ON
10 AVR mode
11 Battery mode
12 Internal fault
13 Output load level
14 Battery level
15 Input measurements
16 Output measurements
17 Measuring unit
Outlets
20
19
18
18 Filtered outlets
19 Battery backup outlets
20 Protection (circuit breaker)

7
614-06819-00
3. UPS connections
• Connect the UPS 1to the AC-power system via a wall outlet with an earth connector,
using the supplied cord 4for a UPS with FR/DIN sockets or with the supply cord of
your computer for a UPS with IEC sockets (seegureA).
• Plug critical equipment (computer, monitor, modem, etc.) into the outlets 19 providing
batterybackuppowerandsurgeprotection(seegureB),takingcarenottoexceed
the rated current indicated in amperes.
• Otherdevices(printer,scanner,fax,etc.)canbeconnecttothelteredoutlets18
thatprovidesurgeprotection(seegureB).Thelteredoutletsarenotbackedupby
battery power in the event of a power outage.
Optional Internet modem / Network connection:
A modem or Ethernet data line can be protected against surges by connecting it via
the UPS. Connect the existing device cable between the wall outlet and the UPS, and
useasimilarcablebetweentheUPSandthedevice,asindicatedingureC(cablenot
supplied).
Optional USB connection:
The UPS device can be connected to the computer using the USB cable 5supplied.
The software is available on the CD-ROM 5or Eaton UPS Companion software is
downloadablefrompowerquality.eaton.com(seegureC).
Register for the warranty on powerquality.eaton.com.
4. Master and EcoControl outlets operating procedure
In order to limit energy consumption of peripherals (scanner, printer) in standby mode,
the Eaton 5S is equipped with EcoControl outlets that are dependent on the Master
outlet. When the main application supplied by the Master outlet (computer) is shut
down, the EcoControl outlets are automatically deactivated and the peripherals shut
down.
Thisfunction(deactivatedbydefault)isvalidatedandconguredusingtheconguration
tool integrated in the software.
Note: when the function is activated, do not connect critical applications to EcoControl outlets.
Threshold setup
A default setup ensures the correct operation of the EcoControl function. However,
depending on the consumption of the main load, the trigger threshold of the EcoControl
functionmayhavetobemodiedusingthecongurationsoftwaresuppliedwiththe
UPS:
• First, make sure that the function is activated in the "EcoControl Function" tab of the
congurationtool.
• If the peripherals connected to the EcoControl outlets do not switch off when the main
load is not in normal operation (ex: when in standby mode), the detection threshold
value must be set to High.
• If the rated consumption level of the main load is low and the EcoControl outlets shut
down when the main load is operating normally, the detection threshold value must
be set to Low.

8614-06819-00
7. Operation
Battery charge
The UPS charges the battery as soon as it is connected to the AC outlet, whether
button 6ispressedornot.Whenusedforthersttime,thebatterywillonlyprovide
its maximum autonomy after it has been charged for 8 hours. It is recommended that
the UPS be permanently connected to the AC power supply to ensure the best possible
autonomy.
Switching-on the UPS
Press button 6for about 1 second.
Filtered outlets 18 without battery backup
Equipment connected to these outlets is supplied as soon as the AC cord 4is plugged
in.They are not affected by button 6.
Battery backup outlets 19
Equipment connected to these outlets is supplied as soon as button 6turns green
(seegureD).
These outlets can be turned on even if the UPS is not connected to AC power
(button 6ashes).
6. UPS setting through the LCD
l LCD shut off if any button inactive for 3 minutes.
5s 2s 2s 2s 2s
(184 - 264 V)
Output voltage Input voltage
tolerance
EcoControl Alarm
(161 - 284 V)
Release scroll down button to select menu
Save the new value
10s 5s 5s
Example of setting

9
614-06819-00
(For further information, visit the www.powerquality.eaton.com site or contact after-sales support.)
Problem Diagnostic Solution
1•The battery backup outlets 19
are not supplied with power.
•Button 6is not lighted on. •Press button 6and check that
it turns green.
2•The connected devices are not
supplied when AC power fails.
•The devices are not connected
to the battery backup outlets 19.
•Connect the devices to the
battery backup outlets 19.
3•AC power is available, but the
UPS operates on battery power. •Circuit breaker 20, located
under the UPS, has been tripped
by an overload on the UPS
output.
•Disconnect excess equipment
and reset the circuit breaker 20
by pressing the corresponding
button.
4•Green button 6ashesand
audio alarm beeps every 3
seconds.
•The UPS battery backup outlets
19 are overloaded.
•Disconnect excess equipment
connected to the battery backup
outlets 19 .
5•Fault sign 12 appear on the
LCD panel and audio alarm beep
continuously.
•A fault has occurred on the UPS.
The battery backup outlets 19 are
no longer supplied.
•Call after-sales support.
6•EcoControl outlets keep powered
when main application (Master
outlet) is stopped.
•EcoControl function is not
activated or not properly set.
•Activate or set properly
EcoControl function using the
software provided with the
product.
8.Troubleshooting
AC-power disturbance
• If AC power is disturbed or fails, the UPS continues to operate on battery power.
Button 6ashesgreen.Innormalmode,theaudioalarmbeepseverytenseconds,
then every three seconds when the end of battery backup time is near. In silent mode
(see the section on settings), the audio alarm simply beeps once when the UPS
transfers to battery power.
• If the power outage lasts longer than the battery backup time, the UPS shuts down
and automatically restarts when power is restored. Following a complete discharge, a
few hours are required to recharge the battery back to full backup time.
• To save battery power, it is possible to press button 6to cut the supply of power to
the devices connected to the battery backup outlets.
Lightning protection:
Alloutlets,whetherbackeduporsimplyltered,includesurgeprotection,whateverthe
position of button 6.
Shutdown of the battery backup outlets 19
Press button 6for more than two seconds.