Eaton 9315 User manual

Powerware 9315 UPS
300–500 kVA
Installation Manual
®

IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the UPS and batteries. Please read all instructions before operating the
equipment and save this manual for future reference.
Consignes de sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
CE MANUEL CONTIENT DES CONSIGNES DE SÉCURITÉ IMPORTANTES
Class A EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING
This is a product for restricted sales distribution to informed partners. Installation
restrictions or additional measures may be needed to prevent disturbances.
Powerware is a registered trademark and ConnectUPS is a trademark of Eaton Corporation.
ECopyright 2004−2007 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this
document may be reproduced in any way without the express written approval of Eaton Corporation.

i
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
Table of Contents
1 Introduction 1−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Using This Manual 1−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Conventions Used in This Manual 1−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 For More Information 1−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 Getting Help 1−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Getting Started 2−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Preparing Your Site 2−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Environment Considerations 2−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Preparing for Wiring the UPS System 2−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 Inspecting and Unpacking Each Cabinet 2−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Installing the UPS 3−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Installing the UPS Cabinet 3−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Prepare for Installing Optional Cabinets or Accessories 3−4. . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Completing the Installation Checklist 3−6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Installing Battery Cabinets 4−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Important Safety Instructions 4−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Installing Input and Output Transformers and Input Filter Cabinets 5−1. . . . . . . . .
6 Installing a Power Distribution Module 6−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Installing a Remote Emergency Power−Off Control 7−1. . . . . . . . . . . . . . . . . . . . . . . . .
8 Installing a Remote Battery Disconnect 8−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 Installing a Remote Monitor Panel 9−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 Installing a Relay Interface Module 10−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 Installing a Supervisory Contact Module 11−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix A – Customer Information A−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents
ii EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
List of Figures
Figure 1-1. Typical Powerware 9315 UPS System 1−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-1. Cabinet as Shipped, with Outer Packaging−Rear View 2−3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-1. Removable I/O Section 3−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-2. Removing Front and Rear Supports 3−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-3. Preparing the UPS for Installation 3−5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-1. Input Transformer Cabinet (480/480V and 600/480V) 5−1. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-2. Five% Input Filter Cabinet (480/480V) 5−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-3. Input Transformer Cabinet (208/480V) 5−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-4. Output Transformer Cabinet (480/208V) 5−4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-5. Installing a 480/480 Vac or 600/480 Vac Input Transformer Cabinet 5−7. . . . . . . . . . . . . . . .
Figure 5-6. Installing a 480/480 Vac Input Filter Cabinet 5−8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-7. Installing a 208/480 Vac Input Transformer Cabinet 5−9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-8. Installing a 480/208 Vac Output Transformer Cabinet 5−10. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-1. Typical PDM Cabinet 6−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7-1. Remote EPO Control 7−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 7-2. Remote EPO 7−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8-1. Remote Battery Disconnect Enclosure 8−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9-1. Remote Monitor Panel 9−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9-2. Terminal Block Bracket 9−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9-3. Wiring an RMP to the UPS 9−4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10-1. Relay Interface Module 10−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10-2. Terminal Block Bracket 10−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10-3. Wiring an RIM to the UPS 10−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-1. Supervisory Contact Module 11−1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-2. Terminal Block Bracket 11−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-3. Wiring an SCM to the UPS 11−2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 11-4. Supervisory Contact Module TB2 11−4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1−1
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
Chapter 1 Introduction
This manual describes how to install your Powerware®9315 uninterruptible power supply
(UPS) system. It contains instructions for installing the UPS and each optional component
and accessory. The information you will use depends on the system you purchased.
Each component of your UPS system is housed in a free-standing cabinet. The cabinets line
up and match in style and color, and have safety shields behind the doors for hazardous
voltage protection. Figure 1-1 shows a typical UPS system that includes at least one of each
component.
Input Cabinet
(Transformer
or Filter)
(optional)
Output
Transformer
(optional)
PDM Cabinet
(optional–
requires
480/208 transformer)
UPS
Cabinet
Battery
Cabinet
(optional)
Figure 1-1. Typical Powerware 9315 UPS System
These basic UPS system configurations are possible:
AThe UPS and one or more battery cabinets
AThe UPS, battery cabinet(s), and a Power Distribution Module (PDM)
AThe UPS, battery cabinet(s), and an input cabinet (transformer or filter)
AThe UPS, battery cabinet(s), PDM, and an input cabinet (transformer or filter)
AThe UPS, battery cabinet(s), an input cabinet (transformer or filter) and an output
transformer cabinet
AThe UPS, battery cabinet(s), PDM, an input cabinet (transformer or filter) and an output
transformer cabinet
You can enhance any of these system configurations by adding optional accessories such as
a Remote Monitor Panel (RMP), Relay Interface Module (RIM), Supervisory Contact Module
(SCM), or Remote Emergency Power−Off (EPO) control.

Introduction
1−2 EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
1.1 Using This Manual
The system you are installing dictates which parts of this manual you should read. Everyone
should read Chapters 1 through 3:
AChapter 1 discusses installation considerations for your entire UPS system.
AChapter 2 tells you how to prepare your site for the installation of your UPS system. It
discusses equipment environmental requirements, inspecting, and unpacking cabinets.
AChapter 3 describes how to install the UPS cabinet.
AChapter 4 contains safety instructions and general notes for installation of the UPS
manufacturer’s optional battery cabinets.
AChapter 5 contains information for installing optional input and output transformer
cabinets.
AChapter 6 contains information for installing the optional PDM.
AChapter 7 discusses installing the optional Remote EPO control.
AChapter 8 contains information for installing the optional remote battery disconnect.
AChapter 9 contains information for installing the optional RMP.
AChapter 10 contains information for installing the optional RIM.
AChapter 11 contains information for installing the optional SCM.
AAppendix A contains important information for planning and installing your UPS system,
including illustrations of cabinets and optional accessories.
Read through each installation procedure before you begin. Perform only those procedures
that apply to the UPS system you are installing.
1.2 Conventions Used in This Manual
This manual uses these type conventions:
AItalic type represents variable information that you must replace with an actual value, or
a directory or file name.
AScreen type represents information that appears on your screen.
ABold type represents a command or option that you type or enter at a prompt.
Icon Description
Information notes call attention to important features or instructions.
[Keys] Brackets are used when referring to a specific key, such as [Enter] or [Ctrl].
In this manual, the term UPS" refers only to the UPS cabinet and its internal elements. The
term UPS system" refers to the entire power protection system – the UPS modules,
battery strings, and options or accessories installed.

Introduction
1−3
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
1.3 For More Information
Refer to the Powerware 9315 (300–500 kVA) UPS Operation Manual for more
information about the operation and communication capabilities of the UPS system:
ADescribes the UPS cabinet Control Panel and Monitor Panel, and explains the functions
of the UPS; discusses the standard features of the UPS and optional accessories; provides
procedures for starting and stopping the UPS, and information about maintenance and
responding to system events.
AAlso described are the RS−485 and RS−232 serial communication capabilities of the UPS
system; how to connect optional remote accessories to your UPS system; and provides
information about enabling, disabling, and customizing building alarms.
Visit www.powerware.com or contact your service representative for information on how to
obtain copies of this manual.
1.4 Getting Help
If you need to schedule initial startup, need regional locations and telephone numbers,
have a question about any of the information in this manual, or have a question this
manual does not answer, please call the Eaton Help Desk for Powerware products at::
In the United States 1-800-843-9433
In Canada 1-800-461-9166
All other countries Call your service representative

Introduction
1−4 EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
This page intentionally left blank.

2−1
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
Chapter 2 Getting Started
Each cabinet of your UPS system is shipped on a separate pallet. Use a forklift or pallet jack
to move the packaged cabinets to the installation site, or as close as possible to the site,
before you unload them from the pallets.
This is the basic sequence of the installation steps:
1. Prepare your site for the UPS cabinet (Chapter 2).
2. Inspect, unpack, and unload the UPS cabinets (Chapter 2).
3. Create an installation plan for the UPS and optional cabinets (Chapter 3).
4. Wire the cabinets together (Chapters 4 through 11, as applicable).
5. Install features, accessories, and/or options (Chapters 4 through 11, as applicable).
6. Complete the Installation Checklist (Chapter 3).
7. Have authorized service personnel perform preliminary checks and startup.
After wiring the UPS system to the facility power and critical load(s), be sure to ground the
system according to local and/or national electrical wiring codes, using your own cabling
and conduit.
Install batteries in accordance with all applicable codes and regulations, including the
National Electrical Code (NEC) Article 480.
NOTE Startup and operational checks should be performed only by authorized service
personnel. This service is usually offered as part of the sales contract for your UPS
system.

Getting Started
2−2 EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
2.1 Preparing Your Site
For your UPS system to operate at peak efficiency, the installation site should meet the
environmental specifications outlined in the Powerware 9315 (300–500 kVA) UPS Operation
Manual. If you intend to operate the UPS at an altitude higher than 1500m (5000 ft),
contact your service representative for important information about high altitude
operation. The operating environment must meet the size and weight requirements shown
in Table N on page A−15.
The basic environmental requirements for operation of the UPS system are:
AAmbient Temperature Range: 0–40°C (32–104°F)
ARecommended Operating Range: 20–25°C (68–77°F)
AMaximum Relative Humidity: 95%
The UPS and input transformer cabinets use forced air cooling to regulate internal
component temperature. The battery and optional component cabinets use convection
cooling to regulate internal component temperature. Air inlets are in the front of the
cabinet, and outlets are in the top. You must allow clearance in front of and above each
cabinet for proper air circulation.
2.2 Environment Considerations
The life of the UPS system is adversely affected if the installation does not meet the
following guidelines:
1. The UPS system must be installed on a sealed concrete pad on a sealed concrete
floor.
2. The UPS system must be installed in a temperature-controlled indoor area free of
conductive contaminants.
2.3 Preparing for Wiring the UPS System
For external wiring requirements, including the minimum AWG size of external wiring, see
Table A through Table G beginning on page A−2. The power wiring connections for this
equipment are rated at 90°C (194°F). If the ambient temperature is greater than 30°C
(86°F), a higher temperature and/or larger size wire may be necessary. Wiring for optional
accessories (such as a Remote Monitor Panel or Relay Interface Module) should be
installed through the knockout in the bottom of the UPS cabinet. The top entry connection
requires installation of 13 mm (0.5″) flexible conduit within the UPS. Bottom entry
connection requires no additional routing of conduit within the UPS.

Getting Started
2−3
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
2.4 Inspecting and Unpacking Each Cabinet
The first task in preparing for installation is inspecting and unpacking each cabinet.
Cabinets arrive covered with protective packaging material as shown in Figure 2-1.
Outer
Packaging
Foam Cushion
Figure 2-1. Cabinet as Shipped, with Outer Packaging−Rear View
1. Carefully inspect the outer packaging for evidence of damage during transit.
CAUTION
Do not install a damaged cabinet. Report any damage to the carrier and your service
representative immediately.
2. Use a forklift or other material handling equipment to move the cabinet to a
convenient unpacking area. Insert the forklift jacks between the foam cushions on
the bottom of the unit.
CAUTION
Do not tilt cabinets more than 10° from vertical.
3. Set each pallet on a firm, level surface, allowing a minimum clearance of
4.6m (15 ft) on each side for removing the cabinets from the pallets.
4. Cut the steel bands around each cabinet.
5. Remove the protective cardboard covering from the cabinets, cutting where
indicated, using a knife blade no longer than 25 mm (1″).
6. Remove the plastic bag and foam packing material, and discard or recycle them in
a responsible manner.

Getting Started
2−4 EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
This page intentionally left blank.

3−1
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
Chapter 3 Installing the UPS
WARNING
Installation should be performed by qualified personnel.
Refer to the following while installing the UPS:
ADimensions in this manual are in millimeters and inches.
ADo not tilt the UPS or other cabinets more than ±10° during installation.
ACooling exhaust airflow is approximately 1420 L/S (3000 CFM).
AThe conduit landing plates are to be removed to add conduit landing holes as required.
Plate material is 16 gauge steel (0.06″thick).
ATerminals E1−E15 are UL and CSA rated at 90°C. A hex key tool is required to attach
wires to the terminals.
AThe Remote Emergency Power−Off feature opens all breakers and contactors in the UPS
cabinet and isolates power from your critical load. Local electrical codes may also
require tripping upstream protective devices to the UPS.
AUPS cabinet must be installed on a level, sealed concrete pad or floor.
AIf perforated floor tiles are required for ventilation, place them in front of the UPS. See
Table N on page A−15 for equipment weight.
AAll circuit breakers provided as part of the UPS system that employ adjustable trip
mechanisms have been set to their maximum settings. Based upon the energy available
and other equipment located on-site, these settings may need to be adjusted to ensure
proper system operation and coordination. It is the customer’s responsibility to conduct
a breaker coordination study, so that these breakers can be adequately set for the site.
ADetails about control wiring are provided in each procedure for connecting options and
features. Table Q on page A−18 identifies the control wiring terminations.
3.1 Installing the UPS Cabinet
WARNING
UPS cabinets are extremely heavy. If unloading instructions are not closely followed, the
cabinet may tip and cause serious injury.
The UPS cabinet is bolted to a sheet metal pallet consisting of four supports secured to
foam cushions. The foam cushions act as shock absorbers for the cabinet during shipment
and movement to the installed location.

Installing the UPS
3−2 EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
See Figure 3-1 before installing the UPS cabinet. The UPS cabinet base is equipped with
forklift slots to accommodate lifting and moving the equipment. The forklift slots are
located on all four sides of the cabinet base to meet individual needs. The wireway section
on the right side of the UPS cabinet (as seen from the front) must be removed to gain
access to the right side fork lift slots (see Figure 3-1).
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓÓ
ÓÓÓ
ÓÓ
ÓÓ
Hidden
Forklift
Slots
Removable
I/O Section
Behind Door
Do Not Lift
Figure 3-1. Removable I/O Section
1. Move UPS to final installed location using forklift jacks between foam cushions on
the bottom of the unit.
2. Remove hardware labeled 1," 2," and 3" in Figure 3-2, holding the front, rear,
and side supports to the cabinet base.
3. Remove the front, rear, and side supports from the cabinet base and foam
cushions. Discard or recycle the hardware and support brackets in a responsible
manner.
CAUTION
Lift only at forklift openings or cabinet damage may occur.
4. Insert the forklift jacks in the forklift slots and raise the UPS cabinet until the
cabinet bottom clears the foam cushions by approximately 3 mm (1/8″).

Installing the UPS
3−3
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓ
ÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓÓ
ÓÓ
ÓÓ
Left Hand Door
I/O Wireway
Rear Support
Side
Support
Foam
Cushion
(4 Places)
Front
Support
3
(4 Places)
2
(8 Places) 1
(16 Places)
Figure 3-2. Removing Front and Rear Supports
5. Pull the foam cushions from under the UPS cabinet. Discard or recycle them in a
responsible manner.
6. Carefully lower the cabinet until the UPS cabinet base contacts the floor.
7. Repeat Steps 1 through 6 for each cabinet you are preparing to install.

Installing the UPS
3−4 EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
3.2 Prepare for Installing Optional Cabinets or Accessories
If you are installing optional cabinets or accessories, such as a Power Distribution Module
cabinet, an input transformer, an output transformer, or a Remote Monitor Panel, you
must install conduit between each device and the UPS cabinet for wiring these options. See
Figure 3-3 for the location of the interface points within the UPS cabinet. Also, refer to the
Powerware 9315 Series 685 and 1085 Auxiliary Battery Cabinets Installation Manual for
information on installing battery cabinets.
To prepare the UPS for wiring to an Input Transformer, Output Transformer, Maintenance
Bypass Cabinet (MBC), PDM, or all:
1. Be sure the UPS is turned off and all power sources are removed. (Refer to the
Powerware 9315 (300–500 kVA) UPS Operation Manual for instructions.)
2. Open the doors of the UPS.
3. Remove stationary right side door and set it aside for later reuse.
4. Remove the air filters and set aside for later reuse.
5. Remove the lower metal access panel. Set the access panel and hardware aside for
later reuse.
To prepare the UPS for wiring to an RMP, Relay Interface Module, Supervisory Contact
Module, or Remote EPO:
1. Be sure the UPS is turned off and all power sources are removed. (Refer to the
Powerware 9315 (300–500 kVA) UPS Operation Manual for instructions.)
2. Open the doors of the UPS.
3. Remove the air filters and set aside for later reuse.
4. Remove the lower metal access panel. Set the access panel and hardware aside for
later reuse.
NOTE A bypass neutral feeder must be supplied when the output neutral is used. If no
bypass neutral is supplied, the output neutral is to be bonded to ground through a
minimum 3/0 copper conductor.

Installing the UPS
3−5
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
ÓÓÓÓ
Left Side Panel
Left Door
TB4 Shunt/UV Trip Signal
Communication Panel I/O Section Wireway (Behind Door)
X−Slot
Communication
Bay
Card Slot
Figure 3-3. Preparing the UPS for Installation
NOTE A bypass neutral feeder must be supplied when the output neutral is used. If no
bypass neutral is supplied, the output neutral is to be bonded to ground through a
minimum 3/0 copper conducter.

Installing the UPS
3−6 EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
3.3 Completing the Installation Checklist
The final step in installing your UPS system is completing the following installation
checklist. This checklist ensures that you have completely installed all hardware, cables, and
other equipment. Completing all items listed on the checklist will ensure a smooth
installation. You should make a copy of the installation checklist before filling it out, and
retain the original.
After the installation is complete, your service representative will be able to verify the
operation of your UPS system and commission it to support your critical load. The service
representative cannot perform any installation tasks other than verifying software and
operating setup parameters. Service personnel may request a copy of the completed
installation checklist to be sure you have completed all applicable equipment installation.
NOTE The installation checklist MUST be completed before starting the UPS system for
the first time.

Installing the UPS
3−7
EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
Installation Checklist
-All packing materials and restraints have been removed from each cabinet.
-Each cabinet in the UPS system is placed in its installed location.
-A ground bond is installed between any cabinets that are bolted together.
-All switchboards, conduits, and cables are properly routed to the UPS and auxiliary cabinets.
-All power cables are properly terminated.
-A ground conductor is properly installed.
-If neutral connection is used, no other N−G bonds exist downstream from the UPS.
-Battery cables and harness are terminated on E4 and E5.
-Internal battery cabinet connections have been completed (bus bars, plugs, etc.).
-Shunt trip signal wiring is connected from UPS to battery breaker(s).
-Air conditioning equipment is installed and operating correctly.
-The area around the installed UPS system is clean and dust-free. (It is recommended that the UPS be
installed on a sealed, concrete pad or a sealed, concrete floor.)
-Adequate workspace exists around the UPS and other cabinets.
-Adequate lighting is provided around all UPS equipment.
-A 120V service outlet is located within 25 ft of the UPS equipment.
-Each Remote Monitor Panel (RMP) is mounted in its installed location. (OPTIONAL)
-The control wiring for each RMP is terminated inside the UPS cabinet. (OPTIONAL)
-The Remote EPO device is mounted in its installed location and its wiring terminated inside the UPS
cabinet. (OPTIONAL)
-Summary alarms and/or building alarms are wired appropriately. (OPTIONAL)
-A RIM is mounted in its installed location and its wiring is terminated inside the UPS cabinet. (OPTIONAL)
-A remote battery disconnect control is mounted in its installed location and its wiring is terminated inside
the UPS and battery cabinet. (OPTIONAL)
-Circuit breakers with adjustable trip mechanisms adjusted to match site requirements.

Installing the UPS
3−8 EATON Powerware®9315 UPS (300–500 kVA) Installation Manual S164201118 Rev H www.powerware.com
Notes
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________