Eaton 93E XL User manual

Eaton® 93E XL UPS
10-40 kVA (380/400/415V)
Installation and Operation Manual

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and maintenance of the UPS
and
batteries. Please read all instructionsbefore operating the equipment and save this manual for future
ref erence.
WARNING
The sales of this product is strictly restricted to knowledgeable service partner (GB/T 17626). To prevent Electromagnetic
Interference (EMI), Extra precaution will be necessary
©2016 Eaton Cor por ation
All Rights
Reserv ed
The contents of this manual are the copyright of the publisher and may not be reproduced (even e xtracts) unless
permissiongranted.
Every care has been taken to ensure the accuracy of the inf ormation contained in this manual, but
no
liability can be accepted for any errors or omission. The right to mak e design modifications is reser v ed.

T able of Contents
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1 UPS StandardFeatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1.1.1 Installation
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.1.2 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.1.3
Customer Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.1.4 High-Efficiency
Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.1.5
Advanced Battery Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.1.6
Maintenance Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.2
Options and A ccessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.2.1 External Battery Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.2.2 Parallel
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1.2.3 Monitoring and
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
1.3 Batter y
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
1.4 Basic
System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
1.5 Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
1.6
Conventions Used inThis Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
1.7
Symbols, Controls, and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
1.8 For More
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
1.9 Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
2 SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . 2-1
3 UPS INSTALLATION PLAN AND UNPACKING
. . . . . . .. . . . . . . . . . . . . . . . . . . . . . . .. . . . . 3-1
3.1 Creating an Installation Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2
Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2.1
Environmental and Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2.2 UPS System P o w er Wiring Preparation .. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 12
3.2.3 UPS System Interface Wiring Preparation. . . . . . . . . .. . . . . . . . . . . . . . . . .. . . . . . .. . . . . . . . . . . . . 18
3.3 Inspecting and Unpacking the UPS Cabinets .. .. . . . . . . . . . . . . . . . .. . .. . . .. . . . . . . . . . . . . . . . .. . .. . 19
4 UPS SYSTEM INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 Preliminary Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Unloading the UPS Cabinet from the Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4.3 External Battery Cabinet Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
4.4 External
P o w er Wiring Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
4.5 Installing
Interface Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
4.5.1 Installing Building Alarm
Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
4.5.2 Installing Parallel Pull Chain and CANControl Wiring and Connections .. . . . . . . . . . . . . .. . .. . . .. . . 31
4.5.3 Installing Mini-Slot Interface Connections .. . . . . . . .. . . . . . . . . . . . . . . .. . . .. . . . . . . . . . . . . . . . . 32
4.6 Installing aREPO Switch .. .. . . . . . .. . . .. . .. . . . . . . . . . . . . . . . .. . . .. . .. . . . . . . . . . . . . . . . .. . . .. .34
4.7 Initial Startup . .. . . . . . . . . . . . . . . . .. . . .. . .. . . . . . . . . . . . . . . . .. . . .. . .. . . . . . . . . . . . . .. . .. . . .. . 37
4.8 Completing the Installation Checklist . . . . . . . . . . . .. . . . . . .. . . . . . . . . . . . . . . . .. . . . . . .. . . . . . . .. . . . 38
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation
1. 1.7 Dual input . . . . . . . .. . . . . . . . . . . . . . . . .. . . .. . .. . . . . . . . . . . . . . . . .. . . .. . .. . . . . . . . . . .
2

Table of Contents
5
UNDERSTANDING UPS OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5.1 UPS System O v er vie w . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5.2 Single UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
5.2.1
Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
5.2.2
Standard Normal Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
5.2.3 High-Efficiency Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
5.2.4
Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
5.2.5 Battery Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
5.3 Single UPS Unit
System Oneline Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
6 UPS OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1 UPS Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1
6.2 Using the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
6.2.1
Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
6.2.2
System Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
6.2.3 Using the LCDand
Pushbuttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
6.2.4 Using the Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
6.2.5 Mimic
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
6.2.6 Display Menu
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
6.2.7
System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
6.3 Single UPS Operation . . . .. . .. . . . . . . . . .. . . .. . . . . . . . . .. . . . . . . . . .. . . .. . . . . . . . . .. . . . . . . . . . . . 58
6.3.1 Starting the UPS in Standard Normal Mode (Default Mode) . . . . . . .. . . . . . . . . . . . . . . . . . .. . . .. . .58
6.3.2 Starting the UPS in Bypass Mode . .. .. . . .. . . .. . . . . . . . . . . . . . . . . . . .. . . .. . . . . . . . . . . . . . . . . 59
6.3.3 Transfer from Normal to Bypass Mode .. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 59
6.3.4 Transfer from Bypass to Normal Mode .. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . .60
6.3.5 Transfer from Standard Normal Mode to HE mode . . . . . . . . .. . . .. . .. . . . . . . . . . . . . . . . .. . . .. . .60
6.3.6 Transfer from HE Mode to Standard Normal Mode . . . . . . . . . .. . .. . .. . . . . . . . . . . . . . . . . .. . .. . . 60
6.3.7 Transfer from Normal Mode to Internal Maintenance Bypass . . . . . . . . . . . . . .. . .. . . .. . . . . . . . . . 6 1
6.3.8 Transfer from Internal Maintenance Bypass to Normal Mode .. . . . . . . . . . . . . . . . .. . . .. . . . . . . . . .61
6.3.9 UPS and Critical Load Shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.3.10 Charger Control . . . . .. . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . . . . . .. . .. . . 6 2
6.3.11 Battery Test .. . . .. . .. . . . . . . . . . . . . . . . .. . . .. . .. . . . . . . . . . . . . . . . .. . .. . . .. . . . . . . . . . . . . . 6 3
6.3.12 Using the UPS LOADOFF Command . . . . . . . . .. . .. . . .. . . . . . . . . . . . . . . . .. . .. . . .. . . . . . . . . . 6 3
6.3.13 Using the Remote Emergency Power-off Switch . . . . . . . .. . .. . .. . . . . . . . . . . . . . . . . .. . .. . .. . . 6 4
6.4 Multiple UPS Parallel Operation . . . . . .. . . . . . .. . . . . . . . . . . . . . . . .. . . .. . .. . . . . . . . . . . . . . . . .. . . .. 6 6
6.4.1 Starting the Parallel UPS in Standard Normal Mode (Default Mode) . . . . . . . . . . . . . . . . . .. . .. . . . . . 6 7
6.4.2 Starting the Parallel UPS in Bypass Mode . . . . . . . . . .. . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . 6 8
6.4.3 Transfer from Normal to Bypass Mode .. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 6 9
6.4.4 Transfer from Bypass to Normal Mode .. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 6 9
6.4.5 Single UPS Shutdown. . . . . . . . . . .. . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . .70
6.4.6 Single UPS Restart . . . . . .. . . . . . . . . . . . . . . . . . . .. . . .. . . . . . . . . . . . . . . . . . . .. . . .. . . . . . . . . . 70
6.4.7 UPS and Critical Load Shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . .. . . 71
6.4.8 Charger Control .. . . .. . . . . . . . . . . . . . . . .. . . . . . .. . . . . . . . . . . . . . . . .. . . . .. . . . . . . . .. . .. . .71
6.4.9 Battery Test . . . . . . . . . . . . . . . .. . .. . .. . . . . . . . . . . . . . . . . .. . .. . .. . . . . . . . . . . . . . . . . .. . .. . . 72
6.4.10 Using the UPS LOADOFF Command . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . .73
6.4.11 Using the Remote Emergency Power-off Switch . . . .. . . . . . . . . . . . . . . . .. . . . . . .. . . . . . . . . . . . .74
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

Table of Contents
7
COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1 Mini-Slot Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.2 Building Alarm Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
8 UPS MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.1 Important Safety Instr uctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.2
PerformingPreventative Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
8.2.1
DAILY Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
8.2.2
MONTHLY Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
8.2.3 PERIODIC
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
8.2.4
ANNUAL Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
8.2.5
BATTERY Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
8.3 Installing
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
8.4 Recycling the Used Battery or UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
8.5
Maintenance Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
9 PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.1 Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.2
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.2.1 UPS
Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.2.2 UPS Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82
9.2.3 UPS
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

Listof Figures
Figure 1-1. Eaton 93E XL UPS (10–40 kVA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 3-1. UPS Cabinet Dimensions 10/15/20/30 kVA (Front, Right Side, and Rear Views) . . . . . . .. . . .. . . . . . . . . . . . . . 10
Figure 3-2. UPS Cabinet Dimensions 40 kV
A (Front, Right Side, and Rear Views) .. . . . . .. . . . . . . . . . . . . . . . . .. . . .. . 11
Figure 3-3. UPS Cabinet Dimensions (Birdand Bottom Views) .. . . . . .. . . . .. . . .. . .. . .. . . . . . . . . . . .. . . . . . . . . . . . . . 11
Figure 3-5. UPS Cabinet as
Shipped on Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .
20
Figure 4-1.
Removing the Shipping Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
Figure 4-2. Attaching the Ramp to the Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Figure 4-3. Rolling the Cabinet Down the Ramp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Figure 4-4.
P o w er Terminal Locations 10/15/20/3 0 kVA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Figure 4-5.
P o w er Terminal Locations 40 kVA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Figure 4-6.
Interf ace Terminal Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
Figure 4-7.
Interf ace Terminal Detail ( T erminal Cover R emo v ed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Figure 4-8. Building AlarmTerminal Block
Connector A ssignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Figure 4-9.
Interface Wiring A ccess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
Figure 4-10. Pull Chain Terminal Block
Connector A ssignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 4-11. Parallel UPS Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Figure 4-12. Parallel UPS
system connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Figure 4-13. REPO Terminal Block
Connector A ssignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
Figure 4-14.
Normally-Open REPO Switch Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
Figure 4-15. Normally-Closed REPO Switch Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
Figure 5-1. Main
Elements of the UPS System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
Figure 5-2. Path of Current Through the UPS in
standard Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42
Figure 5-3. Path of Current Through the UPS in
Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
Figure 5-4. Path of Current Through the UPS in Battery Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
Figure 5-5. UPS
System One line (Dual Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
Figure 5-6. UPS
System One line (Single Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
Figure 6-1. UPS Controls and
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
Figure 6-2. UPS
Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
Figure 6-3. UPS Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
Figure 6-4. Parts of the
LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
Figure 6-5. Main Menu and Mimic
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
Figure 6-6. Typical Initial
Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
Figure 6-7. Typical
System Control Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
Figure 7-1. Optional Mini-Slot Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
Figure 8-1.
Air Filter Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

Listof T ables
Table 3-1. UPS Cabinet Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Table 3-2. UPS Cabinet
Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Table 3-3. UPS Cabinet
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Table 3-4. Air Conditioning or Ventilation
Requirements During Full Load Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Table 3-5. Input
/Output Ratings and External Wiring Requirements for the Eaton 93E XL 10-40 kVA .. . . . . . . . . . . . . .
14
Table 3-6. UPS External Power Cable Terminations for the Eaton 93E XL 10-40 kVA . . . . . . . . .. . .. . . . . . . . . . . . . . . . 15
Table 3-7.
Recommended Input Circuit Breaker Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
Table 3-8. Recommended Bypass Circuit Breaker, and Output Circuit Breaker and Bypass Fuse Ratings. . . . .. . . . . . . . 16
Table 3-9.
Recommended DC input circuit breaker rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Table 4-1. Building Alarm
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Table 4-2. Pull Chain
Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 4-3. REPO
Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
Table 4-4.
Normally-Open REPO Wire Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
Table 4-5. Normally-Closed REPO Wire
Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
Table 6-1.
Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
Table 6-2. Display Function Menu Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
Table 6-3. Display Menu
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
Table 6-4.
Command Menu Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
Table 6-5. Typical
System Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
Table 9-1. UPS Model
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . .
81
Table 9-2. UPS Operating Environment . . . . . . . . . . . . . . . . . . .. . . .. . . . . . . . . . . . . . . . . . . .. . . .. . . .. . .. . . .. . .. . . 81
Table 9-3. UPS Input Rating . . . . . . . . . .. . . . . . . . . . . . . . . . .. . . .. . .. . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . . .. . .. 82
Table 9-4. UPS Output Rating . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . .. . ... . . . . . .. . .. . . 82
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

Chapter 1 Introduction
The Eaton 93E XL 10-40 kVA uninterruptiblepower supply (UPS) is a true online, transf ormer- free, double-
conversion, solid-state, three-phase system,
providing conditioned and uninterruptible AC po w er
to
protect the customer's load from power f ailures. With selectable internal batteries setup configuration of 1-6
strings, each strings with 36 blocks of 9AH batteries.
The Eaton 93E XL 10-40
kVA online power protectionsystem is used to prevent loss of valuable electronic
information,minimise equipment downtime, and minimise the adverse effect on productionequipment due to
unexpected power problems.
The Eaton 93E XL 10-40
kVA UPS continually monitors incoming electrical power and removes the surges,
spik es, sags, and other irregularities that are inherent in commercial utility power. Working with a building's
electrical
system, the UPS system supplies clean, consistent power that sensitive electronicequipment
requires f
or reliable operation. During brownouts, blackouts, and other power interruptions,batteries provide
emergency power to safeguard operation.
The UPS is
housed in a single free-standing cabinet, with safety shields behind the door for hazardous v olt age
protection.
This
manual is for 93E XL series UPS, refer to Table 9-1 for product models.
NOTE1:
Startup and operationalchecks for parallel systems or installations with
accessor y cabinets must be performed by an authorised Eaton Customer Service
Engineer, or the warrantyterms may become void. This service is offered as part of the
sales contract f or the UPS. Contact an Eaton service representative in advance (usually a
two-week notice is required) to reserve a preferred startup date.
Figure 1-1：Eaton 93E XL UPS (10-40 kVA)
1
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

sy stem. This load sharing system provides more capacity than a single UPS, and can provide bac kup .
1.1 UPS Standard Features
The UPS has many standard features that provide cost-effective and consistently reliable power protection.
The descriptions in this section provide a brief overview of the UPS standard f eat ures.
1.1.1 Installation Features
Power wiring can be routed to the rear of the cabinet with connectionsmade to accessible terminals.
1.1.2 Control Panel
The control panel, located on the front of the UPS, contains a liquid crystal display (LCD) and pushbut ton
switches to control the operation of the UPS and to display the status of the UPS system. See Chapter6,
“UPS OperatingInstructions,” for additional inf ormation.
1.1.3 Customer Interface
• Building Alarm Monitoring – Up to three inputs in the UPS are available to connect the facility's alarm
system contacts. Some system configurations may limit the number of inputs available. The UPS uses
these inputs to monitor the building alarms in addition to the UPS status. See Chapter 7,
“Communication,”
for additional inf ormation.
• Mini-Slot Communication Bays – UPS equipped with two communication bays as standard. One of the two
communication bays slotted with a RS232 card as factory default. Min i-Slot cards can be e a s i l y installed at the
front (behind door) of the UPS and are
hot-pluggable. See Chapter 7, “Communication,” f or additional
inf
ormation.
1.1.4 High-Efficiency Mode
The 93E XL Series UPS offers a High-Efficiency (HE) normal mode with double-conversion on demand that
allo
ws the UPS to operate in standby bypass mode. This mode allows the 93E XL UPS to achieve 98%
efficiency
while still protecting the load. See Chapter 6, “UPS OperatingInstructions,” for additional
information. On setting the UPS to work in High Efficiency mode.
1.1.5 Advanced Battery Management
A three-stage charging system increases battery service life by optimizing recharge time, and protects
batteries from damage due to high current charging and inverter ripple currents. Charging at high currents can
overheat
and damage bat teries.
1.1.6 Maintenance Bypass
The internal Maintenance Bypass 93 XL UPS consists of input, output and bypass input (Dual f eeds)
switches used to control the AC input to the UPS the inverter output, and a Maintenance Bypass switch used
to partially isolate the UPS so that a limited
number of components can be serviced without interrupting po w er
to critical sy stems.
1.1.7 Dual input
93E XL series with dual feed input, with separate rectifier input and bypass input terminals.
1.2 Options and Accessories
Contact an Eaton sales representative for information about the following options.
1.2.1 External Battery Cabinet
Battery backup protection is provide by equipping the UPS system with up to four External Battery Cabinets
(EBCs) containingsealed lead-acid, maintenance-freebatteries. The EBCs are housed in single, free-st anding
cabinets designed for line-up-and-match installation, but may be installed separate from the UPS cabinet.
1.2.2 Parallel System
Aparallel UPS system with up to four UPSs can be installed to provide a parallel capacity and/or redundant
2
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

depending on the load and configuration. In addition, when one UPS is taken out of service for maintenance or
is not operating properly, a redundant UPS continues to supply uninterruptedpower to the critical load. A
Controller Area
Network (CAN) Bridge provides connectivity for system metering and operational mode control.
1.2.3 Monitoring and Communication
Mini-Slot Cards – Optional Mini-Slot cards support several protocols, such as WEB/SNMP, RELAY / RS232 and
Modbus.
See Chapter 7, “Communication,“ for additional information on monitoring and communication
f eat ures.
1.3 Battery System
The internal batterysystem (Number of batteries depends on UPS model) pro vides emergency short-term
backup power to safeguard operation during brownouts, blackouts, and other po w er inter r uptions. The battery
system
is equipped with lead-acid bat teries.
1.4 Basic System Configurations
The following basic UPS system configurations are possible ( model dependent ) :
• Single UPS (internal bat ter y selectable from 0-6 strings, each strings consists of 36 blocks of 9AH batteries).
The UPS system configuration can be enhanced by adding optional accessories such as a
Remote Emergency Power-off (REPO) control or Mini-Slot communication cards.
1.5 Using This Manual
This manual describes how to install and operate the Eaton 93E XL 10-40 kVA. Read and understand
the procedures described in this manual to ensure trouble-free installation and operation. In particular,
be thoroughly familiar with the REPO procedure (see paragraph 6.3.1 3).
The
information in this manual is divided into sections and c hapters. The system, options, and accessories
being installed dictate which parts of this manual should be read. At a minimum, Chapters 1 through4
and
Chapter 6 should be e xamined.
Read
through each procedure before beginning the procedure. Perform only those procedures that apply to
the UPS system being installed or operated.
1.6 Conventions Used in This Manual
This manual uses these type con v entions:
• Bold type highlights importantconcepts in discussions, key terms in procedures, and menu options, or
represents a command or option that you type or enter at a prompt.
• Italic type highlights notes and new terms where they are defined.
•Screen type represents information that appears on the screen or LCD.
Icon Description
Note Information notes call attention to important features or instructions.
[Keys]
Brackets are used when referring to a specific key, such as [Enter] and or [Ctrl].
In this manual, the term UPS
refers only to the UPS cabinet and its internal elements. The term UPS sy stem
refers to the entire power protectionsystem – the UPS cabinet, an externalbattery system, and options or
accessories inst alled.
3
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

1.7 Symbols, Controls, and Indicators
The following are examples of symbolsused on the UPS or accessories to alert you to important inf ormation:
RISK OF
ELECTRIC SHOCK - Observe the warning associated with the risk of electric
shock symbol.
CAUTION: REFER TO O P ER A T O R ' S MANUAL - Refer to your operator's m a nu a l f o r
additional
information, such as important operating and maintenance instr uctions.
This symbol
indicates that you should not discard the UPS or the UPS batteries in
the
trash. This product contains sealed, lead-acid batteries and must be disposed of
properly. For more information, contact your local recycling/reuse or hazardous w aste
center.
T h i s s y m bo l i nd i ca t e s that you s hou l d not d i s ca r d waste e l e c t r i ca l or e l e c t r on i c
equipment
(WEEE) in the trash. For proper disposal, contact your local recy cling/reuse or
hazardous waste center.
1.8 For More Information
Refer to the External Battery Cabinet Installation Manual for the following additional inf ormation:
• Installation instructions, including site preparation, planning for installation, wiring and safety inf ormation,
and detailed illustrations of cabinets with dimensional and connection point dra wings
Visit www.eaton.com/powerquality or contact an Eaton servicerepresentative for information on how to
obtain copies of these manuals.
1.9 Getting Help
Ifhelp is needed with any of the follo wing:
• Scheduling initial st artup
• Regional locations and telephone numbers
• A question about any of the information in this manual
• A question this manual does not answ er
Please call your local service represent ativ e.
4
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

Chapter 2 Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during installation and
maintenance of the UPS and batteries. Read all instructionsbefore operating the equipment and save
this manual for future
ref erence.
The UPS is
designed for industrial or computer room applications, and contains safety shields behind
the door and front
panels. However, the UPS is a sophisticatedpower system and should be handled with
appropriate care.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed b y AUTHORISED
SERVICE
PERSONNEL ON L Y . There are NO USER SERVICEABLE PARTS inside the UPS .
W ARNING
• The UPS is suitable for mounting on concrete or other non-combustiblesurfaces only .
• The UPS is powered by its own energy source (bat teries). The output terminals may carry live
voltage even
when the UPS is disconnected from an AC source.
• To reduce the risk of fire or electric shock, install this UPS in a temperature and humidity controlled,
indoor environment, free of conductive contaminants. Ambient temperature must not exceed 25°C
(104°F). Do not
operate near water or excessive humidity (95% maximum). T he system is not intended
for outdoor use.
• As a result of the connected loads high leakage current is possible. Connection to earth ground is
required for safety and proper product operation. Do not check UPS operation by any action that
includes removal of the earth (ground) connection with loads at t ac hed.
• Ensure
all power is disconnected before performing installation or ser vice.
• Batteries can present a risk of electrical shock or burn from high short-circuits cur rent. T he following
precautions should be observed: 1) Remove watches, rings, or other metal objects;
2) Use tools with
insulated handles; 3) Do not lay tools or metal parts on top of batteries; 4) W ear
rubber gloves and boots.
• ELECTRIC ENERGY HAZARD. Do not attempt to alter any UPS or battery wiring or connectors.
Attempting to alter wiring can cause injury .
• Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may be to xic.
• The UPS unit is not suitable for IT or corner-earthed power distribution sy stems.
CAUTION
• Installation or servicing should be performed by qualified service personnel knowledgeable of UPS
and
batterysystems, and requiredprecautions. Keep unauthorizedpersonnel away from equipment.
Consider
all warnings, cautions, and notes before installing or servicing equipment. DO NOT
DISCONNECT the
batteries while the UPS is in Battery mode.
• See installation instructionsbefore connecting to the supply .
• Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to
the
instr uctions.
• Replace batteries with the same number and type of batteries as originally installed with the UPS .
• Disconnect the charging source prior to connecting or disconnecting terminals.
• Determine ifthe battery is inadvertentlygrounded. Ifit is, remove the source of the ground.
Contacting any part of a grounded battery can cause a risk of electric shock. An electric shock is less
2-1
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

likelyif you disconnect the grounding connection before you work on the bat teries.
• Proper disposal of batteries is required. Refer to local codes for disposal requirements.
• Do not dispose of batteries in a fire. Batteries may explodewhen exposed to flame.
• Keep the UPS door closed and front panels installed to ensure proper cooling airflow and to protect
personnel
from dangerous voltages inside the unit.
• Do not install or operate the UPS system close to gas or electric heat sources.
• The operating environment should be maintained within the parametersstated in this manual.
• Keep surroundings uncluttered, clean, and free from excess moisture.
• Observe allDANGER, CAUTION, and WARNING notices affixed to the inside and outside of the
equipment.
2-1
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

Chapter 3 UPSInstallation Plan and Unpacking
Use
thefollowing basic sequence of steps toinstall the UPS:
1. Create an installation plan for the UPS system (Chapter 3).
2. Prepare your site for the UPS system (Chapter 3).
3. Inspect and unpack the UPS cabinet (Chapter 3).
4. Unload and install the UPS cabinet, and wire the system (Chapter 4).
5. Inspect internal battery string, ensure internal breaker at open state, connect battery positive and negative
connections
6. Install
features, accessories, or options, as applicable (Chapter 4).
7. Complete the Installation Checklist (Chapter 4).
8 .. Have authorized service personnel perform preliminary operational checks and start up the sy stem.
NOTE
Startup and operational checks for parallel systems or installations with accessor y
cabinets must be performed by an authorized Eaton Customer Service Engineer, or the
warrantyterms may become void. This service is offered as part of the sales contract f or
the UPS. Contact an Eaton service representative in advance (usually a two-week notice
is required) to reserve a preferred startup date.
CAUTION
It must be ensured that no line input source can accidentally be connected to the UPS
during
inst allation.
WARNING
• Installation may only be carried out by qualified technicians and in conformity with
the
applicable safety st andards.
• The UPS unit is not suitable for IT or corner-earthed power distribution sy stems.
3.1 Creating an Installation Plan
Before installing the UPS system, read and understand how this manual applies to the system
being inst alled. Use the procedures and illustrations in paragraph 3.2 and Chapter 4 to create a
logical plan for installing
the sy stem.
3.2 Preparingthe Site
For the UPS
system to operate at peak efficiency, the installation site should meet the
en vironment al parameters outlined in this manual. Ifthe UPS is to be operated at an altitude
higher than
1000m (3300f t), contact an Eaton service representative for important information
about high altitude operation. The operating environment must meet the weight, clearance, and
environmentalrequirements specified.
3.2.1 Environmental and Installation Considerations
The UPS system installation mustmeet the following guidelines:
• The system must be installed on a level floor suitable for computer or electronic equipment.
• The system must be installed on clean, dust-free, stable concrete, non-corrosive, non-combustible
3-1
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

UPS Installation Plan and Unpacking
surfaces only .
• The UPS operating temperature at ambient 0-40°C .
• The battery operating temperature at ambient 20-25°C .
• Relative humidity at 95%, non-condensing
• The system must be installed in a temperature and humidity controlled indoor area free
of
conductiv e contaminants.
• The system If the UPS is to operate at altitude higher than 1000m (3300ft),
contact an Eaton service representative for further important information on
operating on higher altitude.
Failure to follow
guidelines may void your w ar rant y .
The UPS
equipment operatingenvironment must meet the weight requirements shown in Table 3-1 and the
size requirements shown in Figure 3-1 through Figure 3-5. Dimensions are in millimetres (inc hes).
T able 3-1. UPS Cabinet Weights
Model Weight (
kg )
Net Weight
Gross Weight Descriptions
93E XL-10I-9Ah-MBS 770 859
93E XL-15I-9Ah-MBS 770 859
93E XL-20I-9Ah-MBS 770 859
93E XL-30I-9Ah-MBS 780 869
93E XL-40I-9Ah-MBS 790 879
I- Internal battery
MBS-with internal
MBS
The UPS
cabinetuses forced air cooling to regulate internal component temperature. Air inlets are in the front of the
cabinet and outlets are in the back of the cabinet. Allow clearance in front of and in back of the cabinet for proper air
circulation. The
clearances required around the UPS cabinet are shown in Table 3-2 and Table 3-3
T able 3-2. UPS Cabinet Clearances
From Top of Cabinet At least 300 mm (12") working space
From Front of Cabinet At least 900 mm (36") working space
From Back of Cabinet At least 600 mm (36") working space
From Right Side of Cabinet See Table No: 3-3
From Left Side of Cabinet See Table No: 3-3
8
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

UPS Installation Plan and Unpacking
T able 3-3. 93E XL Required Clearances
93E XL
Required Clearance for paralleled adjacent UPS or UPS and adjacent PDU
Ambient L1(mm) L2(mm)
25 oC
30 oC
35 oC
40 oC
Notes:
≥600 ≤50
• L1- clearance to the rear w all.
• L2-
clearance between the adjacent paralleled UPS or UPS and adjacent PDU. Parallel UPS should be as close
as
possible.
•
Somemodels that feature rear connections also require additional rear clearance to enable installation and
connection.
CAUTION
If batterysystems are located in the same room as the UPS, the battery manuf act urer's
environmentalrequirements should be followed ifthey are more stringent than the UPS
requirements. Operating temperatures above the recommended range willresult in decreased
battery life and performance, and may reduce or void the battery w ar rant y .
The UPS ventilation
requirements are shown in Table 3-4.
T able 3-4. Air Conditioning or V entilation Requirements During FullLoad Operation
Model Power Rating Input / Output V oltage
Heat Dissipation (KC/H)
93E XL-10I-9AH-MBS 10 kVA 380/380 400/400 415/415 523
93E XL-10I-9AH-MBS 15 kVA 380/380 400/400 415/415 862
93E XL-10I-9AH-MBS 20 kVA 380/380 400/400 415/415 1149
93E XL-10I-9AH-MBS 30 kVA 380/380 400/400 415/415 1723
93E XL-10I-9AH-MBS 40 kVA 380/380 400/400 415/415 2298
9
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation

UPS Installation Plan and Unpacking
Front View Right Side View Rear View
Figure 3-1. UPS Cabinet Dimensions 10/15/20/30kVA (Front, Right Side and Rear Views)
Dimension are in millimeters [inches]
10
Eaton 93E XL UPS (10-40kVA, 380/400/415V) Installation and Operation