Eaton BladeUPS none User manual

Powerware Series
Eaton BladeUPS Bar
Installation Guide
® ®

Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of
electric shock symbol.
CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for
additional information, such as important operating and maintenance
instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead‐acid batteries and must be
disposed of properly. For more information, contact your local recycling/reuse or
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
Eaton, Powerware, and BladeUPS are registered trademarks of Eaton Corporation or its subsidiaries and affiliates.
Pozidriv is a registered trademark of Phillips Screw Company. All other trademarks are properties of their respective
companies.
ECopyright 2008–2010 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.

Eaton BladeUPS Bar Installation Guide S164201723 Rev 2 www.eaton.com/powerquality i
Table of Contents
1 Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspecting the Equipment 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools Required 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking the Package Contents 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BladeUPS Bar Installation 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BladeUPS Bar Installation (Bottom Entry Wireway) 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BladeUPS Bar Installation (Top Entry Wireway) 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Specifications 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Service and Support 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Warranty 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limited Warranty 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTS
Eaton BladeUPS Bar Installation Guide S164201723 Rev 2 www.eaton.com/powerquality
ii

Eaton BladeUPS Bar Installation Guide S164201723 Rev 2 www.eaton.com/powerquality 1
Chapter 1 Introduction
Paralleled Eaton BladeUPS®uninterruptible power systems (UPSs) use
the Eaton BladeUPS Bar to provide the required input and output
connections. The BladeUPS Bar installs in an industry standard rack and
is available in two models:
SBladeUPS Bar 4-High: Connects up to four of the BladeUPS modules.
SBladeUPS Bar 6-High: Connects up to six of the BladeUPS modules.
Figure 1 shows the installed BladeUPS Bar in a bottom entry and
top entry wireway configuration. The wireway fits into the bottom or top
6U of standard rack space.
Wireway
Wireway
BladeUPS Bar BladeUPS Bar
Bottom Entry Wireway Top Entry Wireway
Figure 1. BladeUPS Bar Installed in Rack (BladeUPS Bar 6-High Shown)

INTRODUCTION
Eaton BladeUPS Bar Installation Guide S164201723 Rev 2 www.eaton.com/powerquality
2
Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the BladeUPS Bar. Please read all instructions before operating the
equipment and save this manual for future reference.
VIGTIGE SIKKERHEDSANVISNINGER
GEM DISSE ANVISNINGER
Denne manual indeholder vigtige instruktioner, som skal følges under installation og
betjening af BladeUPS Bar-enheden. Læs venligst alle instruktioner inden betjening af
udstyret og gem denne manual mhp. fremtidige opslag.
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
BEWAAR DEZE INSTRUCTIES
Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en
het gebruik van BladeUPS Bar. Lees alle instructies voordat u de apparatuur in bedrijf neemt
en bewaar deze handleiding als naslagwerk.
TÄRKEITÄ TURVAOHJEITA - SUOMI
SÄILYTÄ NÄMÄ OHJEET
Tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava BladeUPS Bar-yksikön
asennuksen ja käytön yhteydessä. Lue kaikki ohjeet ennen laitteiston käyttöä ja säilytä ohje
myöhempää tarvetta varten.
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel contient des instructions importantes que vous êtes invité à suivre lors de toute
procédure d'installation et de fonctionnement de la BladeUPS Bar. Veuillez consulter
entièrement ces instructions avant de faire fonctionner l'équipement et conserver ce manuel
afin de pouvoir vous y reporter ultérieurement.

INTRODUCTION
Eaton BladeUPS Bar Installation Guide S164201723 Rev 2 www.eaton.com/powerquality 3
WICHTIGE SICHERHEITSANWEISUNGEN
AUFBEWAREN
Dieses Handbuch enthält wichtige Hinweise, welche Sie bei der Installation und Wartung
des BladeUPS Bar beachten sollten. Bitte lesen Sie alle Anweisungen des Handbuches
bevor sie mit dem Gerät arbeiten. Bewaren Sie das Handbuch zum Nachlesen auf.
IMPORTANTI ISTRUZIONI DI SICUREZZA
CONSERVARE QUESTE ISTRUZIONI
Il presente manuale contiene importanti istruzioni da seguire durante l'installazione e il
funzionamento di BladeUPS Bar. Leggere integralmente le istruzioni prima di utilizzare
l'apparecchiatura e conservare il presente manuale per futuro riferimento.
VIKTIGE SIKKERHETSINSTRUKSJONER
GJEM DISSE INSTRUKSJONENE
Denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og
bruk av BladeUPS Bar. Les alle instruksjoner før utstyret tas i bruk, og gjem håndboken til
fremtidig referanse.
INSTRUÇÕES DE SEGURANÇA IMPORTANTES
GUARDE ESTAS INSTRUÇÕES
Este manual contém instruções importantes que devem ser seguidas durante a instalação e
operação da BladeUPS Bar. Leia todas as instruções antes de operar o equipamento e
guarde este manual para consultá-lo futuramente.
ÂÀÆÍÛÅ ÓÊÀÇÀÍÈß ÏÎ ÌÅÐÀÌ ÁÅÇÎÏÀÑÍÎÑÒÈ
ÑÎÕÐÀÍÈÒÅ ÝÒÈ ÓÊÀÇÀÍÈß
 äàííîì ðóêîâîäñòâå ñîäåðæàòñÿ âàæíûå èíñòðóêöèè ïî óñòàíîâêå è
îáñëóæèâàíèþ âíåøíåãî áàòàðåéíîãî ìîäóëÿ èëè óñòðîéñòâà ðàñïðåäåëåíèÿ
ýëåêòðîïèòàíèÿ. Ïåðåä ðàáîòîé ñ îáîðóäîâàíèåì ïðî÷òèòå âñå èíñòðóêöèè.
Ñîõðàíèòå äàííîå ðóêîâîäñòâî äëÿ äàëüíåéøåãî èñïîëüçîâàíèÿ.

INTRODUCTION
Eaton BladeUPS Bar Installation Guide S164201723 Rev 2 www.eaton.com/powerquality
4
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
GUARDE ESTAS INSTRUCCIONES
Este manual contiene instrucciones importantes que debe seguir durante la instalación y el
funcionamiento del BladeUPS Bar. Por favor, lea todas las instrucciones antes de poner en
funcionamiento el equipo y guarde este manual para referencia en el futuro.
VIKTIGA SÄKERHETSFÖRESKRIFTER
SPARA DESSA FÖRESKRIFTER
Den här anvisningen innehåller viktiga instruktioner som du ska följa under installation och
användning av BladeUPS Bar. Läs alla instruktioner innan du använder utrustningen och
spara den här anvisningen för framtida referens.

Eaton BladeUPS Bar Installation Guide S164201723 Rev 2 www.eaton.com/powerquality 5
Chapter 2 Installation
This section explains:
SEquipment inspection
SBladeUPS Bar setup and installation
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and file
a claim for shipping damage. If you discover damage after acceptance,
file a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with
the carrier within 15 days of receipt of the equipment; 2) Send a copy of
the damage claim within 15 days to your service representative.
Setup
The BladeUPS Bar comes with all hardware required for installation in a
standard EIA or JIS rack with square and round mounting holes.
Tools Required
To assemble the components, you may need the following tools:
STorque wrench with the following attachments:
- Hex socket size 10 mm for M6 hex bolt
- Hex socket size 8 mm for M5 hex bolt
STorque driver with a Pozidriv®#2 for Pozidriv M4 screw
SLarge screwdriver or crowbar for lifting the bar in place
SPliers for installing cage nuts

INSTALLATION
Eaton BladeUPS Bar Installation Guide S164201723 Rev 2 www.eaton.com/powerquality
6
Checking the Package Contents
Verify that the following items are included in the package:
SOne of the following BladeUPS Bars:
BladeUPS Bar 4-High. A four-socket bar with (1) attached terminal block
assembly, (1) attached terminal block assembly bracket, and
(2) attached mounting brackets
BladeUPS Bar 6-High. A six-socket bar with (1) attached terminal block
assembly, (1) attached terminal block assembly bracket, and
(3) attached mounting brackets
SWireway main housing with (2) attached side brackets, (1) attached
terminal block housing, and (1) attached wireway access cover
SFront cover mounting panel
S(2) front covers
SFerrite assembly with 38 cm (15”) tie wrap
SThis user's guide
SPackaged hardware items:
-BladeUPS Bar 4-High. (12) M6 12 hex bolts, plus (1) extra
-BladeUPS Bar 6-High. (14) M6 12 hex bolts, plus (1) extra
- (4) M5 16 hex bolts
- (6) M6 12 pan-head screws, plus (1) extra
- (3) M4 8 pan-head screws
- (6) M6 split lock washers, plus (1) extra
- (4) M5 cage nuts
- (3) M6 hex nuts, plus (1) extra
BladeUPS Bar Installation
Follow the appropriate procedure for the BladeUPS Bar wireway
location:
SFollow the procedure “BladeUPS Bar Installation (Bottom Entry
Wireway)” on page 7 if you are installing the bar with the wireway at
the bottom of the rack.
SFollow the procedure “BladeUPS Bar Installation (Top Entry
Wireway)” on page 17 if you are installing the bar with the wireway at
the top of the rack.