Eaton Sure-Lites ADX142857 User manual

INS #
ADX142857 049-255 Sure-Lites
Installation Instructions for the Sure-Lites SEL Emergency Lights
without Remote Capacity
WARNING
Risk of Fire/Electric Shock
If not qualified, consult an electrician.
WARNING
Risk of Electric Shock
Disconnect power at fuse or circuit breaker before
installing or servicing.
Important Safeguards
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING
THE FOLLOWING.
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Do not use outdoors.
3. Do not use in hazardous locations, or near gas or electric
heaters.
4. Do not let power supply cords touch hot surfaces.
5. Use caution when servicing batteries. Battery acid can
cause burns to skin and eyes. If acid is spilled on skin or in
eyes, flush acid with fresh water and contact a physician
immediately.
6. Do not use this equipment for other than the intended use.
7. Installation is to be performed only by qualified personnel.
8. Install in accordance with National Electric Code and local
regulatory agency requirements.
9. The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
10. Equipment should be mounted in locations and at heights
where it will not readily be subjected to tampering by
unauthorized personnel.
11. SAVETHESE INSTRUCTIONS
MAX MOUNTING HEIGHT:
17.24 FT for SEL25 models
25.39 FT for SEL50 models
INSTALLATION
1. De-energize the circuit at the junction box (J-box) where
the emergency light is to be installed.
2. Open the emergency light by inserting a screwdriver in the
two slots at the bottom of the unit, then tipping the cover
up off of the backplate.
3. To mount to a junction box - Drill out the appropriate
mounting pattern and the wire pass hole in the backplate
to fit the J-box being used.
4. To mount to conduit – Cut out the U shaped knockout on
the cover using snips, then attach the 1/2” conduit hub to
the backplate.
5. Once the backplate is secured, the housing can be held in
place during installation using the EZ Hang feature. (see
Fig. 1)
6. Connect the incoming wires to the fixture’s power supply
wires using the wire nuts provided. Connect the white
wire to neutral. If using 120V, connect the black wire to the
hot lead. If using 277V, connect the orange wire to the hot
lead. Cap the unused lead. Secure the emergency light
to the wall and/or junction box using installer supplied
hardware.
7. Connect the battery to the PCB. See schematic for detail.
8. Snap the cover onto the backplate.
9. Energize AC supply. The test button should illuminate, and
LED heads will illuminate briefly when the test button is
pushed.
10.Adjust the heads as needed.
11. If the fixture is to be powered down for an extended
period after initial installation, replace the EZ Key.This
will prevent the battery from discharging when AC power
is removed. However, it will also prevent the battery
from charging when AC power is restored, so it must be
removed once the unit is ready for regular operation.

OPERATION
Depress the test switch. The LED heads will remain lit and the
charge LED will extinguish. LED heads will illuminate as long as
the button is pushed. Release the test switch.The charge LED
will illuminate and the LED heads will turn off.
MAINTENANCE
None required. Replace the batteries as needed according
to ambient conditions. However, we recommend that the
equipment be tested regularly in accordance with local codes.
NOTE: Servicing of any parts should be performed by qualified
personnel. Only use replacement parts supplied by Eaton’s
Cooper Lighting business.
CAUTION: This equipment is furnished with a sophisticated low
voltage battery dropout circuit to protect the battery from over
discharge after its useful output has been used. Allow 24 hours
recharge time after installation or power failure for 90 minute
testing.
TROUBLE SHOOTING GUIDE
If LED heads or charge indicator LED does not illuminate, check
the following:
1. Check AC supply – verify that unit has 24 hour AC supply.
2. Unit is shorted or battery is not connected.
3. Battery discharged. Permit unit to charge for 24 hours and
then re-test.
4. If following the above trouble shooting hints does not
solve your problem, contact your local Cooper Lighting
representative for assistance.
SCHEMATIC
SEL with Base Heads
+
CN4
U2
D10
MOV2
U1
SW1
R15
R14
R13
R12
R11
R10
R9
R8
R7
R6
R5
R4
R3
R2
R1
Q5 Q4
Q3
Q2
Q1
MOV1
LED1
JK1
F1
D9
D8
D6
D5
D4
D3
D2
D1
CN3
CN2
CN1
C2
C1
R16
C3
R17
R18
LED/SW
277 N120
JMP1
c
LAMPS
BATT
Base Heads -
Mounted on Fixture
Battery
ORANGE - 277VAC
BLACK - 120VAC
WHITE - NEUTRAL
SEL with Higher Power Heads
Battery
Higher Power Heads
- Mounted on Fixture
ORANGE - 277VAC
BLACK - 120VAC
WHITE - NEUTRAL
+
R18
R17
F2
C1
C2
C3
CN1
CN2
CN3
D1
D2
D3
D4
D5
D6
D7
D8
D9
F1
JK1
JK2
JK3 JK4
JK5
LED1
MOV1
MOV2
Q1
Q2
Q3
Q4
Q5
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
SW1
U1
U2
CN4
-
-
-
-
+
+
+
+
+
BATT
LAMPS
-
RMT
277120N
LED/SW
J1
c
Figure 1
Slide snaps through holes
in housing for temporary
mount when wiring.
WARRANTIES AND LIMITATION OF LIABILITY
Please refer to www.eaton.com/LightingWarrantyTerms for our
terms and conditions.
Eaton
1121 Highway 74 South
Peachtree City, GA 30269
eaton.com/lighting
© 2015 Eaton
All Rights Reserved
Printed in USA
Publication No. ADX142857
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
ADX142857