EBN Technology X-POS855A User manual

User’s Manual
X-POS855A

Copyrights i
Copyrights
©2013All rights reserved. The information in this
document is subject to change without prior notice in
order to improve reliability, design and function and does
not represent a commitment on the part of the
manufacturer.
This document contains proprietary information
protected by copyright. All rights are reserved. No
part of this manual may be reproduced by any
mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
All trademarks are property of their respective
owners
Liability Disclaimer
In no event will the manufacturer be liable for direct,
indirect, special, incidental, or consequential
damages arising out of the use or inability to use the
product or documentation, even if advised of the
possibility of such damages.
Regulatory Information
FCC Notices
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the Federal Communications Commission
(FCC) Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Increase the separation between the equipment
and the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio or
television technician for help.
This device complies with Part 15 (A) of the FCC
Rules. Operation is subject to the following two
conditions:
1) this device may not cause harmful interference
and
2) this device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS DEVICE. SUCH
MODIFICATIONS COULD VOID THE USER'S
AUTHORITY TO OPERATE THE DEVICE.
CE Notice
This device complies with EMC Directive
2004/108/EC issued by the Commission of the
European Community.

Copyrights ii
WEEE Notice
The WEEE mark applies only to countries within the
European Union (EU) and Norway.
This appliance is labeled in accordance with
European Directive 2002/96/EC concerning waste
electrical and electronic equipment (WEEE). The
Directive determines the framework for the return
and recycling of used appliances as applicable
throughout the European Union. This label is applied
to various products to indicate that the product is not
to be thrown away, but rather reclaimed upon end of
life per this Directive.
RoHS Notice
This device is full compliance with EU Directive
2002/95/EC (the RoHS Directive) that restricts the
use of the hazardous sub stanceslisted below in
electrical and electronic equipment.
Safety Statement for Lithium Battery

Contents iii
Contents
Copyrights .................................................................................................i
Liability Disclaimer ...................................................................................i
Regulatory Information.............................................................................i
FCC Notices.......................................................................................................... i
CE Notice.............................................................................................................. i
WEEE Notice........................................................................................................ ii
RoHS Notice ........................................................................................................ ii
Safety Statement for Lithium Battery................................................................ ii
Contents...................................................................................................iii
1. Hardware Setup....................................................................................4
1.1. Packing Contents......................................................................................... 4
1.2. Quick Tour .................................................................................................... 5
1.3. Basic Peripherals Installation ..................................................................... 6
1.4. HDD Replacement...................................................................................... 14
1.5. Adjust Angle ............................................................................................... 16
1.6. VESA Wall-mount Kit Installation (X-PCC855 only)................................. 16
1.7. Turn on the device...................................................................................... 16
2. Basic Driver Installation ....................................................................17
2.1. Before the installation................................................................................ 17
2.2. Chipset Software Installation .................................................................... 17
2.3. VGA Driver Installation .............................................................................. 19
2.4. LAN Driver Installation............................................................................... 21
2.5. Audio Driver Installation............................................................................ 22
2.6. Touch Driver Installation (Only for Windows XP).................................... 24
3. I/O Definition.......................................................................................27
3.1. Power Connector ....................................................................................... 27
3.2. Serial Port................................................................................................... 27
3.3. Cash Drawer............................................................................................... 28
4 Dimension............................................................................................29
5 Specification........................................................................................30

Chapter 1 Hardware Setup 4
1.
1. Hardware Setup
1.1. Packing Contents
1. Device X 1 5. IO Panel Cover X 1
2. Power Adapter X 1 6. Drive and Utility DVD X 1
3. Power Cord X 1 7. Wall mount kit (X-PPC855 only)
4. RJ50 to DB9 COM port adapter cable X 1

Chapter 1 Hardware Setup 5
1.2. Quick Tour
Front View and Side View
LED Indicator
A. The Power indicator will glow green when power is on.
B. The HDD indicator will blink green when the HDD is accessed.
A. Power switch D. Customer Display mounting hole cover
B. MSR cover E. Wi-Fi antenna mounting hole
C. HDD tray F. I/O cover

Chapter 1 Hardware Setup 6
Back Panel I/O
A. DC-in jack G. Cash Drawer port
B. RJ50 port for COM2 H. USB 3/4 port
C. USB 1/2 port I. COM 3 port
D. LAN 1 port J. VGA port
E. LAN 2 port K. Parallel port
F. COM 1 port L. CF card slot
1.3. Basic Peripherals Installation
1. All cables and wires from peripherals to the POS device are recommended to
be fed through the base in the direction as shown below.

Chapter 1 Hardware Setup 7
Power Adapter
1. Assembly the power adapter to the power adapter bracket, and feed the DC
connecter through the base.
2. Install the adapter bracket onto the POS device by tightening two screwsas
shown.
3. Connect the DC connector of the power adapter to the DC-in jack.
USB Mouse, USB Keyboard, USB ODD and other USB Devices
Connect your USB Mouse, USB Keyboard and USB ODD to USB 1/2 or UBS 3/4
ports on the back panel of the device.

Chapter 1 Hardware Setup 8
LAN Cable
Connect one end of RJ-45 LAN cable to the LAN 1 or LAN 2 port on the back
panel of the device, another end to your internet device.
Cash Drawer
Connect one end of RJ-11 cable to the Cash Drawer port on the back panel of the
device, another end to your cash drawer.
Printer
Connect the parallel cable of the printer to the LPT1 (parallel port) on the back
panel of the device.
IO panel cover
Install the IO panel cover onto the device.

Chapter 1 Hardware Setup 9
Customer Display
A. Hardware Installation
1. Remove the two screws fixing the customer display cover, Remove the VFD
mounting hole cover from the device and pull out the connector from the device.
2. Adjust angle for hinge of the VFD, and then connect to the device as shown
below.
3. Mount the VFD to the device and tighten the two M3 screws as shown below.
4. Finished.

Chapter 1 Hardware Setup 10
B. Power Supply Configuration
WARNING
Never enable the 12V without the customer display attached and be
sure to disable the 12V before removing the customer display.
1. Power up the X-POS855and hit the DEL key to enter the BIOS. When the BIOS
screen appears use the or key on your external computer keyboard to select
Advanced. Use the arrow keys of the external key board to select IO Configuration,
and then press the ENTER key.
2. The screen below will appear. Use the or key to scroll the screen and highlight
theCOM6RI/12V/15V, and then press the Enter key.

Chapter 1 Hardware Setup 11
3. Highlight12V, and then press the Enter key.
4.Press the ESC key to return to the BIOS SETUP UTILITY screen of step 1, use the
or key on your external computer keyboard to select the EXIT.
Use the or key to highlight Save Changes and Exit.

Chapter 1 Hardware Setup 12
5. Press the Enter key, use the or key to highlight the [Ok], press the Enter key
again to save your voltage configuration and exit BIOS.
MSR
1. Remove the two screws fixing the MSR cover.
2. Remove the MSR cover from the device.

Chapter 1 Hardware Setup 13
2. For MSR with fingerprint sensor or
MSR with RFID sensor, connect the
two connectors of the MSR assembly
to the device.
MSR with fingerprint sensorMSR with RFID sensor
2. For MSR or MSR with iButton, connect
the connector of the MSR assembly to
the device.
MSR MSR with iButton
3. Tighten the two M3 screws to fix the MSR assembly as shown below.

Chapter 1 Hardware Setup 14
4. Finished.
MSR with fingerprint sensor MSR with RFID sensor
MSR
MSR withiButton
1.4. HDD Replacement
1. Loosen and remove the screws fixing the HDD tray.

Chapter 1 Hardware Setup 15
2. Pull out the HDD tray slightly and softly.
3. Disconnect the SATA cable connector and SATA power cable connector.
4. Loosen and remove the four screws fixing the HDD, and then remove the HDD
from the HDD tray.
5. Install the new HDD onto the device in reverse order.

Chapter 1 Hardware Setup 16
1.5. Adjust Angle
1.6. VESA Wall-mount Kit Installation (X-PCC855 only)
1. Install the device bracket.
2. Put the X-PPC855 onto the wall bracket which is preinstalled on the wall..
1.7. Turn on the device
1. Make sure all peripherals are connected properly.
2. Press and hold the power switch until the power indicator on the front panel
glows green.

Chapter 2 Basic Driver Installation 17
2.
2. Basic Driver Installation
2.1. Before the installation
1. Connect an external USB CDROM to the USB port and insert the driver
CD and turn on the device. The program Auto Runs and displays the
DRIVER BANK screen.
2. Follow the on-screen instructions.
2.2. Chipset Software Installation
1. On the main screen, click “X-POS855/X-PPC855 Series”.
2. Click INTEL Chipset Driver.
3. Click Next.

Chapter 2 Basic Driver Installation 18
4. Read the License Agreement carefully and click Yes.
5. Click Next.
6. Click Finish.

Chapter 2 Basic Driver Installation 19
2.3. VGA Driver Installation
1. On the main screen, click “XPOS855/X-PPC855 Series”.
2. Click VGA Driver.
3. Click VGA Driver for WINDOWS.
4. Click Next.