EBN Technology X-PPC 710 User manual

User’s Manual
X-PPC 710

Copyrights
©2011 All rights reserved. The information in this
document is subject to change without prior notice in
order to improve reliability, design and function and does
not represent a commitment on the part of the
manufacturer.
This document contains proprietary information
protected by copyright. All rights are reserved. No
part of this manual may be reproduced by any
mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
All trademarks are property of their respective
owners
Liability Disclaimer
In no event will the manufacturer be liable for direct,
indirect, special, incidental, or consequential
damages arising out of the use or inability to use the
product or documentation, even if advised of the
possibility of such damages.
Regulatory Information
FCC Notices
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the Federal Communications Commission
(FCC) Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Increase the separation between the equipment
and the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio or
television technician for help.
This device complies with Part 15 (A) of the FCC
Rules. Operation is subject to the following two
conditions:
1) this device may not cause harmful interference
and
2) this device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS DEVICE. SUCH
MODIFICATIONS COULD VOID THE USER'S
AUTHORITY TO OPERATE THE DEVICE.
CE Notice
This device complies with EMC Directive
2004/108/EC issued by the Commission of the
European Community.
i
Copyrights

WEEE Notice
The WEEE mark applies only to countries within the
European Union (EU) and Norway.
This appliance is labeled in accordance with
European Directive 2002/96/EC concerning waste
electrical and electronic equipment (WEEE). The
Directive determines the framework for the return
and recycling of used appliances as applicable
throughout the European Union. This label is applied
to various products to indicate that the product is not
to be thrown away, but rather reclaimed upon end of
life per this Directive.
RoHS Notice
This device is full compliance with EU Directive
2002/95/EC (the RoHS Directive) that restricts the
use of the hazardous substances listed below in
electrical and electronic equipment.
Safety Statement for Lithium Battery
ii Copyrights

Contents
Copyrights .................................................................................................i
Liability Disclaimer ...................................................................................i
Regulatory Information.............................................................................i
FCC Notices.......................................................................................................... i
CE Notice .............................................................................................................. i
WEEE Notice........................................................................................................ ii
RoHS Notice ........................................................................................................ ii
Safety Statement for Lithium Battery ................................................................ ii
Contents...................................................................................................iii
1. Hardware Setup....................................................................................4
1.1. Quick Tour .................................................................................................... 4
Front View and Side View .............................................................................. 4
Back Panel I/O ............................................................................................... 5
1.2. Basic Peripherals Installation ..................................................................... 5
Power Adapter ............................................................................................... 5
USB Mouse, USB Keyboard and USB ODD .................................................. 5
LAN Cable...................................................................................................... 6
Cash Drawer .................................................................................................. 6
Customer Display........................................................................................... 6
WiFi Module ................................................................................................... 7
1.4. VESA Wall-mount Kit Installation.............................................................. 10
1.5. Turn on the device.......................................................................................11
2. Basic Driver Installation ....................................................................12
2.1. Before the installation................................................................................ 12
2.2. Chipset Software Installation .................................................................... 12
2.3. VGA Driver Installation .............................................................................. 13
2.4. Touch Screen Driver and Software Utility installation ............................ 15
2.5. LAN Driver Installation............................................................................... 18
3. eGalaxy Touch Control Utility Quick Guide .....................................22
3.1. Launch eGalaxy Touch Control Utility...................................................... 22
3.2. General........................................................................................................ 22
3.3. Settings....................................................................................................... 24
3.4. Tools............................................................................................................ 27
3.5. Edge Compensation .................................................................................. 28
4. I/O Definition.......................................................................................31
5.1. Power Connector ....................................................................................... 31
5.2. Serial Port ................................................................................................... 31
5.3. Cash Drawer ............................................................................................... 31
iii
5 Specification........................................................................................33
Contents

1.
1. Hardware Setup
1.1. Quick Tour
Front View and Side View
LED Indicator
The Power indicator will:
1. glow green when the power is on
2. glow red when the HDD is accessed.
Chapter 1 4

Back Panel I/O
1.2. Basic Peripherals Installation
Remove the rear I/O board cover from the device.
Power Adapter
Connect the DC cable to the DC in jack.
USB Mouse, USB Keyboard and USB ODD
Connect your Mouse and Keyboard to the mouse/keyboard port, and USB ODD
to the USB ports on the back panel of the device.
Chapter 1 5

LAN Cable
Connect one end of RJ-45 LAN cable to the LAN port on the back panel of the
device, another end to your internet device.
Cash Drawer
Connect one end of RJ-11 cable to the Cash Drawer port on the back panel of the
device, another end to your cash drawer.
Install the rear I/O board cover onto the device.
Customer Display
A. Hardware Installation
1. Remove the two screws fixing the customer display cover, and then remover
the VFD mounting hole cove from the device and pull out the connector from the
device.
Chapter 1 6

3. Adjust the hinge of the VFD, and then connect to the device as shown below.
4. Mount the VFD to the device and tighten the two M3 screws as shown below.
5. Finished.
WiFi Module
1. Remove the IO panel cover (if installed) form the device.
Chapter 1 7

2. Un-tighten four screws.
3. Open the device, and you’ll see the two antenna cable fixed by black acetate
tape.
4. Below is the layout of the Wi-Fi module.
Chapter 1 8

6. Assemble the WiFi module, antenna and WiFi module cable as shown.
8. Connect the another end of the WiFi module cable to the 4 pin USB header
(USB 4) on the main board. For the location of the USB4 on the main board,
please refer to the figure below.
9. Reassembly the device.
Chapter 1 9

B. Power Supply Configuration
Power up the XPPC710 and hit the DEL key to enter the BIOS. When the BIOS screen
appears use the TAB key to select Advanced. Use the arrow keys to select Super IO
Configuration then type ENTER. The screen below will appear. Use the arrow keys to
select Serial Port 6 RI/12V depending on what port the customer display is connected
to. Select 12V to enable power to the correct COM port. Type F10 to save the settings
and exit the BIOS setup.
Caution: Never enable the 12 V without the customer display attached and be sure to
disable the 12 V before removing the customer display.
NOTE: The figure above is for reference only; it is possible that the actual screen on
your device does not agree with it.
1.4. VESA Wall-mount Kit Installation
1. Install the device bracket.
2. Put the XPPC 710 onto the wall bracket which is preinstalled on the wall.
3. Tighten the screw.
Chapter 1 10

1.5. Turn on the device
1. Make sure all peripherals are connected properly.
2. Press and hold the power switch until the power indicator on the front panel
glows green.
Chapter 1 11

2.
2. Basic Driver Installation
2.1. Before the installation
1. Connect an external USB CDROM to the USB power and insert the driver
CD and turn on the device. The program autoruns and displays the DRIVER
BANK screen.
2. Follow the on-screen instructions.
2.2. Chipset Software Installation
1. On the main screen, click “XPOS 72 / XPPC72 / XPPC 710Series”.
2. Click INTEL Chipset Driver.
3. Click Next.
Chapter 2 12

4. Read the License Agreement carefully and click Yes.
4. Click Next.
6. Click Finish.
2.3. VGA Driver Installation
1. On the main screen, click “XPOS 72 / XPPC72 / XPPC 710Series”.
Chapter 2 13

2. Click VGA Driver.
3. Click VGA Driver for WIN2K/XP.
4. Click Next.
5. Read the License Agreement carefully and click Yes.
6. Click Next.
Chapter 2 14

7. Click Next.
8. Select restart your computer right now or later, and then lick Finish.
2.4. Touch Screen Driver and Software Utility installation
1. On the main screen, click “XPOS 72 / XPPC72 / XPPC 710Series”.
2. Click Touch Panel Driver.
Chapter 2 15

3. Click an item according to your needs. .
4. Click Next.
5. Click Next.
6. Check the Install PS/2 interface driver box and click Next.
Chapter 2 16

7. Select an item according to your needs, and then click Next.
8. If you want to use Multi-Monitor, check the box and click Next.
9. Click Next.
10. Click Next, and then the program will be installed automatically.
Chapter 2 17

11. Under Microsoft Windows Embeded, click “start” menu and select “All
Programs”, under ”eGalaxy Touch” menu, click “Configure Utility”.
12. Under General tab, click Add, and then all controller will be detected and
added.
2.5. LAN Driver Installation
1. On the main screen, click “XPOS 72 / XPPC72 / XPPC 710Series”.
Chapter 2 18

2. Click RTL8111C LAN Drive.
3. Click an item according to your needs. .
4. Click Next.
5. Click Install.
Chapter 2 19