Ecco Gemineye EC2014-C User manual

Do not install and/or operate this safety product unless you have read and understand the
safety information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices
are essential to ensure the safety of you and those you are trying to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that
s/he can operate the system without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use,
the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open
trunks or compartment doors), people, vehicles, or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an
intersection, driving against trafc, responding at a high rate of speed, walking on or around trafc lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying
all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal laws
and regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.
WARNING!
Failure to install or use this product according to manufacturers recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
!
Installation Instructions
Camera/Monitor System
Introduction:
ECCO’s Gemineye™ Camera Systems are designed to provide rear of
the vehicle information that may not be available to a driver relying
solely on a vehicle’s standard rear view mirror system. A driver using a
properly installed and maintained rear view camera system in
conjunction with the standard mirror system, can be alerted to potential
safety hazards and thus take the appropriate action to prevent an
accident. This manual provides information about installation, function,
safety, maintenance, replacement parts, and warranty.

Specications:
Camera EC2014-C
Image 1/3” CMOS Color
Effective Pixels: 725 x 488
Voltage Requirement 12V
Power Consumption 3 W
Lens F=2.8mm / F=2.0
Lens Angle 120°
Audio Yes
Light Sensor Auto Switch B&W
Infrared LEDs 11 (10M Max. Visibility)
Pigtail Connection: CAM Male 4 Pin Threaded
Housing Aluminum Alloy
Mech. Vibration 10g
Weight 0.74 lbs
Dimensions (WxHxD) 2.87”x2.99”x2.60”
Operating Temp. -22°F to 158°F
IP Rating IP69K
Approvals FCC, CE, C-Tick, E13/R10
Current Draw 0.25A
Monitors EC5603-M 5.6” LCD Monitor EC7003-M 7” LCD Monitor
Image 5.6” LCD Color, 4:3 7” LCD Color, 16:9
Controller Internal/3 Camera Internal/3 Camera
Voltage 12/24VDC 12/24VDC
Power Consumption 5 W 6 W
Mirror Imaging Yes (via Camera and Monitor Switch) Yes (via Camera and Monitor Switch)
Split Screen Feature No No
AV Compatible No No
DVR Compatible No No
Audio Yes Yes
Contrast/Brightness Yes Yes
Light Sensor Day/Night Auto Dim Day/Night Auto Dim
Camera Selection Trigger Wires and Monitor Trigger Wires and Monitor
Connection: CAM Female 4 Pin Threaded Female 4 Pin Threaded
Connection (Monitor Pigtail) Male 13 Pin Male 13 Pin
Connection: CB N/A N/A
Housing Plastic Plastic
Mounting Permanent - HD (2 bracket options
provided)
Permanent - HD (2 bracket options
provided)
Mech. Vibration Pedestal Bracket - 3g
Cradle Bracket - 8g
Pedestal Bracket - 3g
Cradle Bracket - 8g
Weight 2.67 lbs 3.34 lbs
Dimensions (WxHxD) 6.32”x4.52”x1.07” 7.28”x5.07”x1.06”
Operating Temp -4°F to 158°F -4°F to 158°F
Remote Control Yes Yes
Current Draw 0.4A 0.5A
Approvals FCC, CE, C-Tick, E13/R10 FCC, CE, C-Tick, E13/R10

Caution! When drilling into any vehicle surface, make sure that the area is free from any electrical wires, fuel lines,
vehicle upholstery, etc. that could be damaged.
!
Installation, Wiring and Function
Notes:
1. Larger wires and tight connections will provide longer service life for components. For high current wires it is recommended
that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation
displacement connectors (e.g., 3M Scotchlock type connectors)
2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to
reduce voltage drop. High ambient temperatures (e.g., under-hood) will signicantly reduce the current carrying capacity of
wires, fuses, and circuit breakers. All wiring should conform to the minimum wire size and other recommendations of the
manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and similar installation
hardware should be used to anchor and protect all wiring.
3. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the
wiring and devices.
4. Particular attention should be paid to the location and method of making electrical connections and splices to protect these
points from corrosion and loss of conductivity.
5. Ground termination should be only be made to substantial chassis components, preferably directly to the vehicle battery.
6. Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot enviroments or operated
close to their capacity.
Important! Mount the camera at a location that provides the best view of the area immediately behind the vehicle.
Generally, mounting locations toward the top of the vehicle provide the best eld of view. Lower mounting locations reduce
the eld of view and increase the likelihood of damage from road spray.
1. Find an appropriate location for installation.
2. Drill holes according to the size of U-bracket and x the U-bracket.
3. Drill a 3/4” (19mm) hole next to U-bracket.
4. Install the camera and sun-visor on U-bracket.
5. Connect the camera tail with the extension cable from inside the vehicle.
6. Loosen the hex head screws and adjust the camera’s position to get the best view angle in the monitor.
Figure 1
Installation:
Camera Model EC2014-C

Wiring:
ECTC20-4
Important! Waterproof all connections whether inside or outside the vehicle by using sealant and wrapping with
insulation tape. Wrap tape tightly, overlapping by one-half widths so there are no gaps.
Figure 2
13 PIN FEMALE 13 PIN MALE
CAM 3
CAM 2
CAM 1
Brown Trig. Wire CAM 3
Blue Trig. Wire CAM 2
White Trig. Wire CAM 1
Black (Ground) -
Red (Power) +
2A INLINE FUSE SUPPLIED
WIRING DEFINED

WARNING!
To prevent accidental shock, DO NOT OPEN THE MONITOR CASE. Opening the monitor case will expose the
inside of the monitor to conditions that could adversely affect performance. Any evidence of tampering with
sealed components will void the warranty.
!
Important! Do not expose the monitor to water, it is not waterproof. Any water that leaks into the monitor could cause
extensive damage.
Monitors:
Models EC5603-M and EC7003-M
Installation instruction of using U-support bracket
1. Select suitable position on vehicle and x the U-support bracket with screws (Figure 3)
2. Fix the monitor to the U-support bracket with angle adjustment screws and adjust the view angle of the monitor
3. Put on the sun-visor and connect the monitor with the AV and power supply conversion cable (Figure 4)
Figure 3
Figure 4
Installation:EC5603-M/EC7003-M

Installation instruction of using pedestal base
1. Select suitable position on vehicle and x the base support. (Figure 6)
2. Fix the monitor to the base support and adjust the view angle.
3. Put on the sun-visor and connect the monitor with the AV and power supply conversion cable (Figure 7)
Figure 6
Figure 7
Stick the base
support onto the
vehicle

Remote Control Operaon

Monitor Parts Idenficaon
EC5603-M
EC7003-M
Color LCD
Screen
Remote Signal IR Receiver
Power
Menu
Menu Selecon and Display Mode
Volume Down
Volume Up
Speaker
Installaon port for
center mount bracket
Camera Select
Light Level
Sensor

Menu Operaons
Press the Menu buon on the remote control or the Menu buon on the monitor screen.
Press the Menu buon several mes to go from one menu to another. Use the channel up/down on the remote control
or the down buon on the monitor screen highlight a menu.
To select the highlighted menu, either use the right brightness color on the remote control or the + buon on the
monitor screen. Press the less brightness buon on the remote control or the – buon on the monitor screen to go
back to the previous menu.
Main Menu
Menu
Opons
Press Menu 1 time
Picture
Bright
Adjust brightness
Contrast
Adjust contrast
Color
Adjust color
Volume
Adjust volume
Auto Dim
On/Off
Scale Adjust
On/Off
Press Menu 2 times
Opon
Language
English
Deutsch
Fran
Espańol
Portuguẻs
Italiano
Nederlands
Pyccкий
Scale
On/Off
Cam 1
Normal/Mirror
Cam 2
Normal/Mirror
Cam 3
Normal/Mirror
Press Menu 3 times
Systems
Color Sys
Auto/PAL/NTSC
Blue Back
On/Off
Horizontal
Vercal
Zoom
16:9/4:3
Press Menu 4 times
Auto Scan
Auto Scan
On/Off
Scan Time
1-90 seconds
Cam 1
On/Off
Cam 2
On/Off
Cam 3
On/Off
Press Menu 5 times
ExitMenu
Main Menu Menu Options
Press Menu 1 time Picture Bright Adjust brightness
Contrast Adjust contrast
Color Adjust color
Volume Adjust volume
Auto Dim On/Off
Scale Adjust On/Off
Press Menu 2 times Option Language English
Deutsch
Fran
Español
Portuguẻs
Italiano
Nederlands
Pyccкий
Scale On/Off
Cam 1 Normal/Mirror
Cam 2 Normal/Mirror
Cam 3 Normal/Mirror
Press Menu 3 times Systems Color Sys Auto/PAL/NTSC
Blue Back On/Off
Horizontal ← →
Vertical ↑ ↓
Zoom 16:9/4:3
Press Menu 4 times Auto Scan Auto Scan On/Off
Scan Time 1-90 seconds
Cam1 On/Off
Cam 2 On/Off
Cam 3 On/Off
Press Menu 5 times Exit Menu

Manufacturer Limited Warranty and Limitation of Liability:
Manufacturer warrants that on the date of purchase, this product will conform to Manufacturer’s specications for this product
(which are available from the Manufacturer upon request). This Limited Warranty extends for twelve (12 ) months from the
date of purchase.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UN-
APPROVED MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING
MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTAL-
LATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.
Exclusion of Other Warranties:
MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED. THE IMPLIED WARRANTIES FOR
MERCHANTABILITY, QUALITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEAL-
ING, USAGE OR TRADE PRACTICE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE
HEREBY DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ORAL STATEMENTS OR REP-
RESENTATIONS ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.
Remedies and Limitation of Liability:
MANUFACTURER’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEG-
LIGENCE), OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS
USE SHALL BE, AT MANUFACTURER’S DISCRETION, THE REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE
REFUND OF THE PURCHASE PRICE PAID BY BUYER FOR NON-CONFORMING PRODUCT. IN NO EVENT SHALL
MANUFACTURER’S LIABILITY ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO THE
MANUFACTURER’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE PRODUCT BY BUYER AT THE TIME OF THE
ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUB-
STITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR
OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH
RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR
AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty denes specic legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages.