Eccotemp CEL10 User manual

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
23
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
OUTDOOR GAS WATER HEATER
Eccotemp Systems, LLC
Add: 315-A Industrial Road, Summerville, SC 29483 USA MADE IN CHINA
Country of Destination BE, FR, GB, GR, IE
IT, PT, ES, CH
I 3+
28-30/37
28-30/37
20
35
0.60
G30/G31
I 3B/P
30
30
20
35
0.60
G30
I 3B/P
50
50
42
57
0.50
G30
CY, CZ, DK, EE, FI, LT
MT, NL, NO, SK, SI, SE
HU, BG, LV, LU, RO DE, AT, CH, SK
Gas Pressure
Applicable Water Pressure (mpa)
Appliance Categories
Supply Pressure (mbar)
Min Gas Pressure (mbar)
Max Gas Pressure (mbar)
Supply Pressure (mbar)
Injector Size (mm)
Heat Input (Hs)
Type of Gas
006319
PIN NO. 0063CR7706
MODEL: CEL10
WARNING
0.025-0.1
16 (kW)
Read this instruction before use.
For outdoor use only.
Warning: Accessible parts may be very hot, Keep young children away.
Never move it during operation. Wait for about 7 minutes after extinguished the flame before moving it.
Check the gas type before you connect it to the water heater, improper gas will cause serious danger.
This heater is not to be used in wind speeds above 10kph. The heater will extinguish at used in wind
speed above 10kph. This feature is governed by the safety featured fitted to the appliance.
This appliance must not be used in enclosed areas, for example under awnings or tents.
The appliance must be hung correctly before use. Never use the appliance placed on the ground.
This appliance must be installed in accordance with any national situation in force in the country of use.
This appliance should be sited in an open area using, a natural surround features to protect it from
direct winds.
CHAUFFEEAU À GAS DE PLEIN AIR
Systèmes Ecotemp, LLC
Add: 315-A Industrial Road, Summerville, SC 29483 USA FABRIQUÉ EN CHINE
Pays de destination BE, FR, GB, GR, IE
IT, PT, ES, CH
I 3+
28-30/37
28-30/37
20
35
0.60
G30/G31
I 3B/P
30
30
20
35
0.60
G30
I 3B/P
50
50
42
57
0.50
G30
CY, CZ, DK, EE, FI, LT
MT, NL, NO, SK, SI, SE
HU, BG, LV, LU, RO DE, AT, CH, SK
Pression d'eau applicable (mpa)
Catégories d'appareils
Pression d'alimentation (mbar)
Pression du gaz min (mbar)
Pression du gaz max (mbar)
Pression d'alimentation (mbar)
Dimensions de l'injecteur (mm)
Apport de chaleur (Hs)
Type de gaz
006319
PIN NO. 0063CR7706
MODÈLE: CEL10
AVERTISSEMENT
0.025-0.1
16 (kW)
Lisez ces instructions avant utilisation.
Pour usage extérieur seulement.
Attention: les parties accessibles peuvent être très chaudes. Éloignez des jeunes enfants.
Ne jamais déplacer pendant le fonctionnement. Attendre pendant environ 7 minutes après extinction de la flamme
avant de le déplacer.
Vérifiez le type de gaz avant de le brancher au chauffe-eau, du gaz incorrect peut cause un grave danger.
Cet appareil de chauffage ne doit pas être utilisé sous des vitesses de vent supérieures à 10km/
h. Le chauffe-eau va s'éteindre dans une vitesse de vent au-dessus de 10km/h. Cette fonction est
régie par le dispositif de sécurité monté sur l'appareil.
Cet appareil ne doit pas être utilisé dans des espaces clos, par exemple sous des auvents ou des tentes.
Cet appareil doit être accroché correctement avant l'utilisation. Ne jamais utiliser l'appareil placé sur le terrain.
Cet appareil doit être installé conformément à toutes les régulations nationales en vigueur dans le pays
d'utilisation.
Cet appareil doit être installé dans une zone ouverte, dans des caractéristiques naturelles le protégeant des vents
directs.
Pression du gaz
GAS GEISER
Eccotemp Systems, LLC
315-A Industrial Road, Summerville, SC 29483 USA
Land van bestemming BE, FR, GB, GR, IE
IT, PT, ES, CH
I 3+
28-30/37
28-30/37
20
35
0,60
G30/G31
I 3B/P
30
30
20
35
0,60
G30
I 3B/P
50
50
42
57
0,50
G30
CY, CZ, DK, EE, FI, LT
MT, NL, NO, SK, SI, SE
HU, BG, LV, LU, RO DE, AT, CH, SK
Nominale waterdruk (mPa)
Categorieën apparatuur
Toevoerdruk (mbar)
Min gasdruk (mbar)
Maxgasdruk (mbar)
Toevoerdruk (mbar)
Injectorgrootte (mm)
Warmtetoevoer (Hs)
Gastype
0063-19
PIN NO. 0063CR7706
MODEL: CEL10
WAARSCHUWING
0,025-0,1
16 (kW)
Deze instructies doorlezen vóór gebruik.
Alleen voor gebruik buiten.
Waarschuwing: uitstekende delen kunnen zeer heet worden. Houd jonge kinderen op afstand.
Nooit verplaatsen tijdens gebruik.Wacht na het doven van de vlam minstens 7 minuten alvorens het system te
verplaatsen.
Controleer het gastype voordat u het gas op de geiser aansluit. Gebruik van het verkeerde type gas kan zeer gevaarlijk zijn.
Deze geiser mag niet gebruikt worden bij windsnelheden boven 10 km/u. De geiser zal automatisch uitgaan indien gebruikt
bij windsnelheden boven 10 km/u. Dit is een ingebouwde veiligheidsfunctie.
Dit apparaat mag niet in afgesloten ruimtes zoals onder luifels of in tenten gebruikt worden.
Dit apparaat moet vóór gebruik op de juiste manier zijn opgehangen. Gebruik het apparaat nooit terwijl het op de grond
staat.
Dit apparaat moet volgens de plaatselijke normen in het land van gebruik worden geïnstalleerd.
Dit apparaat dient in een open ruimte geplaatst te worden, beschermd tegen wind.
Gasdruck
AUSSENMONTIERTER GASDURCHLAUFERHITZER
Eccotemp Systems, LLC
315-A Industrial Road, Summerville, SC 29483 USA
Bestimmungsland BE, FR, GB, GR, IE
IT, PT, ES, CH
I 3+
28-30/37
28-30/37
20
35
0,60
G30/G31
I 3B/P
30
30
20
35
0,60
G30
I 3B/P
50
50
42
57
0,50
G30
CY, CZ, DK, EE, FI, LT
MT, NL, NO, SK, SI, SE
HU, BG, LV, LU, RO DE, AT, CH, SK
Anwendbarer Wasserdruck (mPa)
Gerätekategorien
Gasdruck-Zufuhr (mbar)
Gasdruckminimum (mbar)
Gasdruckmaximum (mbar)
Gasdruck-Zufuhr (mbar)
Injektorgröße (mm)
Wärmezufuhr
Gasart
006319
PIN NO. 0063CR7706
MODELL: CEL10
WARNUNG
0,025-0,1
16 (kW)
Lesen Sie die Anleitungen vor der Inbetriebnahme.
Nur für den Aussenbereich.
Warnung: Die zugänglichen Teile können sehr heiss werden. Kinder fernhalten!
Bei Betrieb nicht versetzen. Warten Sie etwa 7 Minuten nach dem Verlöschen der Flamme bis Sie den Erhitzer versetzen.
Prüfen Sie die Gasart vor dem Anschluss des Erhitzers; durch unzulässiges Gas entsteht große Gefahr.
Diesen Erhitzer bei Windgeschwindigkeiten von über 10km/h nicht verwenden. Bei Windegeschwindigkeiten von über
10km/h, wird die Flamme des Erhitzers verlöschen. Diese Sicherheitsfunktion ist im Gerät eingebaut.
Das Gerät darf nicht in geschlossenen Räumen/Bereichen eingesetzt werden, wie zum Beispiel unter Markisen oder
Zelten.
Das Gerät muss vor der Inbetriebnahme sachgemäss aufgehängt werden. Niemals das Gerät auf dem Boden stehend
einsetzen.
Dieses Gerät muss gemäß den nationalen Bestimmungen des jeweiligen Landes der Inbetriebnahme installiert werden.
Dieses Gerät sollte im offenen Bereich eingesetzt werden in einem natürlichen, vor direkten Winden geschützten Umfeld.
Gasdruck

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
23
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
IMPORTANT SAFETY INFORMATION READ ALL
INSTRUCTIONS BEFORE USING
Be sure to read and understand the entire Use and Care Manual before attempting to install
or operate this water heater. It may save you time and money. Pay particular attention to the
Safety Instructions. Failure to follow these warnings could result in serious bodily injury or
death. Should you have problems understanding the instructions in this manual, or have any
questions, STOP, and get help from a qualied service technician, or the local gas utility.
DANGER!
PROPERLY INSTALL WATER HEATER
Failure to properly install the water heater outdoors as outlined in the
Installation
Instructions in this manual can result in unsafe operation of the water heater.
To avoid the risk of re, explosion, or asphyxiation from carbon monoxide,
never operate this water heater unless it is installed properly and has an
adequate air supply for proper operation. Be sure to inspect the ue terminal
for proper installation at initial start-up; and at least annually thereafter.
Refer to the Care and Cleaning section of this manual for more information
regarding ue terminal inspection.
WARNING!
Gasoline, as well as other ammable materials and liquids (adhesives, solvents,
paint thinners etc.), and the vapors they produce are extremely dangerous. DO
NOT handle, use or store gasoline or other ammable or combustible materials
any where near or in the vicinity of a water heater or any other appliance. Be
sure to read and follow the labels on the water heater, as well as the warnings
printed in this manual. Failure to do so can result in property damage, bodily
injury or death.
Installation:
Do not Install water heater where ammable products will be stored or used
unless the main burner ame Is at least 18” above the oor. This will reduce, but
not eliminate, the risk of vapors being ignited by the main burner ame.
Read and follow water heater warnings and Instructions. If owners manual is
missing, contact the retailer or manufacturer.
Vapors from ammable
liquids will explode and catch re
causing death or severe burns.
Do not use or store ammable products
such as gasoline, solvents or adhesives
In the same room or area near the
water heater.
Keep ammable products :
1. Far away from heater
2. In approved containers
3. Tightly closed
4. Out of children‘s reach
Water heater has a main burner ame.
The main burner ame
1. Can come on at any time and
2. Will ignite ammable vapors.
Vapors:
1. Cannot be seen
2. Are heavier than air
3. Go a long way on the oor
4. Can be carried from other rooms
to the main burner ame by air
currents.

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
45
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
FOR YOUR RECORDS
Write the model and serial numbers here:
#_______________________________
#_______________________________
You can nd them on a label on the appliance
and/or packaging.
Staple sales slip or canceled check here.
Proof of the original purchase date is needed to obtain
service under the warranty.
READ THIS MANUAL
Inside you will nd many helpful hints on how to
use and maintain your water heater properly. A
little preventive care on your part can save you time
and money over the life of your water heater. You’ll
nd many answers to common problems in the
Troubleshooting Guide. If you review the chart of
Troubleshooting Tips rst you may not need to call for
service.
READ THE SAFETY INFORMATION
Your safety and the safety of others are very important.
There are many important safety messages in this
manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol. Recognize
this symbol as an indication of Important Safety
Information! This symbol alerts you
to potential hazards that can kill or hurt
you and others.
All safety messages will follow the safety alert symbol
and the words: “DANGER”, “WARNING”, “CAUTION”
or “NOTICE”.
These words mean:
DANGER - An imminently hazardous situation
that will result in death or serious injury.
WARNING - A potentially hazardous situation
that could result in death or serious injury
and/or damage to property.
CAUTION - A potentially hazardous situation
that may result in minor or moderate injury.
NOTICE: Attention is called to observe a
specied procedure or maintain a specic
condition.
General Safety ........................... 1-6
Construction & Parts ................ 8
Getting Started ............................. 9
Use and Starting ................. 10-11
Troubleshooting Guide ..... 12-13
Technical Support ...................... 14
Congratulations!
You’ve just purchased a new
Eccotemp L10 portable tankless
water heater. This will open a
world of enjoyment to going
tankless.
We highly suggest you take
the time to read through all
of the safety and installation
procedures in this manual,
before attempting to install
your new water heater.
Should you have any
questions, please feel free to
visit our helpdesk located at
gb.eccotemp.com for further
information.

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
45
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
DANGER!
NATURAL GAS AND LIQUEFIED PETROLEUM MODELS
Both LP and natural gas have an odorant added to aid in detecting a gas leak. Some people may
not physically be able to smell or recognize this odorant. If you are unsure or unfamiliar with the
smell of LP or natural gas, ask the gas supplier. Other conditions, such as “odorant fade,” which
causes the odorant to diminish in intensity, can also hide or camouage a gas leak. Always
check with commercial leak detector or soapy water.
Gas detectors are recommended in LP and natural gas applications and their installation
should be in accordance with the detector manufacturer’s recommendations and/or local
laws, rules, regulations or customs.
• Water heaters utilizing LP gas are dierent from natural gas models. A natural gas water
heater will not function safely on LP gas and vice versa.
• No attempt should ever be made to convert the water heater from natural gas to LP gas.
To avoid possible equipment damage, personal injury or re, do not connect the water
heater to a fuel type not in accordance with the portable tankless water heater data plate;
propane for propane portable tankless water heaters and natural gas for natural gas
portable tankless water heaters. These portable tankless water heaters are not certied for
any other fuel type.
• LP appliances should not be installed below grade (for example, in a basement) if such
installation is prohibited by federal, state and/or local laws, rules, regulations or customs.
• Propane or LP gas must be used with great caution. It is heavier than air and will collect
rst in lower areas making it hard to detect at nose level.
• Before attempting to light the water heater, make sure to look and smell for gas leaks.
Use a soapy solution to check all gas ttings and connections. Bubbling at a connection
indicates a leak that must be corrected. When smelling to detect a gas leak, be sure to
sni near the oor also.
• It is recommended that more than one method, such as soapy solution, gas detectors, etc.,
be used to detect leaks in gas applications.
Notice: If a gas leak is present or suspected:
• DO NOT attempt to nd the cause yourself.
• DO NOT try to light any appliance.
• DO NOT touch any electrical switch.
• DO NOT use any phone in your building.
• Leave the house immediately and make sure your family and pets leave also.
• Leave the doors open for ventilation and contact the gas supplier, a qualied service
agency or the re department.
• Stay away from the house (or building) until the service call has been made, the leak
is corrected and a qualied agency has determined the area to be safe.

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
67
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
ADDITIONAL WARNINGS
1. Do not leave unattended.
2. The exhaust gas and top of the portable tankless water
heater is HOT! Do not place hands or any foreign object
near the top of the heater.
3. Do not use in high wind conditions.
4. If the smell of gas is detected, turn o the gas valve at the
tank immediately! Do not use ame for leak detection.
5. Use only Liquid Propane.
6. Use only outdoors.
7. Do not over tighten the gas regulator connection to the
portable tankless water heater with a wrench. This may
cause a crack in the gas regulator.
The Eccotemp L-10 is a liquid propane red water heater capable of delivering 7.5 to
10 liters per minute of hot water almost anywhere. The portable tankless water heater
has standard 1/2”NPT pipe ttings and an adapter for using a standard garden hose
for inlet water supply.
The L10 is not a toy. People around the world use similar portable tankless water
heaters to heat the water around their homes, safely, and reliably.
Gas is supplied from a standard propane cylinder (not included) such as used with
outdoor grills. A regulator with hose is furnished with the heater.
You may also plumb it in to existing water lines and using a low pressure LP gas
regulator. Check local codes for proper installation.
The portable tankless water heater includes a stainless steel rain cap that helps
protects it for outdoor usage.
Ignition is automatic and powered by 2 “D” cell batteries (not included). Burners come
on when water ows, and o when the water is shut o. No pilot light.
The Purpose and Benets the L10

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
67
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
Functions and Features
• Water controlled automatic ignition: Water pressure between 20-80 PSI and 2.9-3.8 LPM
opens the ignition circuit for easy and convenient operation.
• Auto-cut-o protection: The auto-cut-o protection will shut the gas supply o immediately
in the event of ameout to reduce the risk of gas leakage.
• Removable drain valve to avoid water pipe and regulator damage caused by freezing water*.
• Anti-dry combustion protection: The portable tankless water heater will shut o the gas
supply in the event water stops owing through the portable tankless water heater.
*Temperature increases listed are based on use of the water heater under optimal
conditions. Variable factors such as incorrect or imperfect installations and varying
incoming water temperatures may yield dierent results.
*Read the maintenance section on draining the portable tankless water heater entirely to
avoid freeze issues
TEMPERATURE INCREASE PER LPM
MODEL Gas Setting 5.5 LPM 7.5 LPM 9.5 LPM 11 LPM
L10
Portable
Highest ° 53 ° 27 ° 18 ° 14 °
Lowest ° 19 ° 9 ° 6 ° 5 °
TECHNICAL SPECIFICATIONS -
PORTABLE
Fuel Type LPG (Liquid propane gas)
Model L10
Ignition Electric Pulse, D cell Battery Powered
(No electrical connection required)
Protections Auto-cut o water control, automatic
ignition, anti-dry combustion protection,
over-pressure overheating and ameout
protection
Dimensions 38 x 16.5 x 89 cm
Pipe Fittings 1/2” BSP, incoming/outgoing water
& gas
Additional Techincal
Specication
See page 13.

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
89
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
Construction and parts for the L10
Flame sensor pin
Important notes:
Normal use and care of the unit does not require removal of the cover. Cover should be
securly in place prior to operation of the unit. Only remove the cover of the unit at the
direction of troubleshooting or support. Sealed individual components do not contain
user servicable parts, not not open or modify any individual component.

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
89
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
1. Check box for damage. Damages caused in shipment must be reported immediately.
2. Make sure you have all the parts.
Please note: Included parts and accessories may vary depending on county and regulations.
3. If using a standard garden hose, attach the 3/4” NPT to garden hose adapter to the tting
marked ‘Water Input”. Use Sealant tape or other approved sealing method on the threads for a
secure, water tight t. Check to make sure the screen inside the water inlet is in place and clean.
Then attach your water input/garden hose.
4. Install gas supply line and regulator to the portable tankless water heater. DO NOT OVER
TIGHTEN. OVER TIGHTING MAY CRACK THE GAS REGULATOR CAUSING A GAS LEAK! Check for
any gas smell before ignition! Make sure it is screwed all the way on.
5. Attach the water output to the tting marked ‘Water Outlet.’ Do not over tighten.
6. Install two “D” cell batteries in the compartment on the bottom left of the heater. Check that
batteries are facing the correct direction.
7. Use the top tab on the portable tankless water heater to suspend from a mounted screw capable
of holding 15 kilograms. Place at a comfortable height without putting stress on the gas hose.
qty. 1 -
Water heater
qty. 1 -
Hardware pack
qty. 1 -
1/2” NPT to garden
hose adapter
qty. 1 - Gas
hose
and regulator
qty. 1 - 1/2”
Compression Fitting
(Not available in all countries)
Getting Started
WARNING!
GAS HOSE ADAPTER
THE L5, & L10 PORTABLE TANKLESS WATER HEATERS HAVE A 1/2’’ TO 1/4” LH
ADAPTER IN THE HARDWARE PACK FOR ATTACHMENT OF THE LP HOSE TO THE
HEATER.
THIS ADAPTER MUST BE INSTALLED WITH THREAD SEALANT, A SPOOL OF
SEALANT TAPE IS INCLUDED WITH THE HEATER.
MULTIPLE WRAPS OF SEALANT TAPE MAY BE
NECESSARY TO ASSURE COMPLETE SEAL.
ALWAYS CHECK FOR GAS LEAKS BEFORE USING HEATER.
With 1/2” compression tting adapter
8a. If your water heater comes with the 1/2”
compression tting adapter rst attach the adapter
to the gas input pipe using 2 wrenches, one on the
gas inlet pipe holding it in place and the other on
the adapter tightening it in place. Next, attach the
gas regulator hose to the LP tank using a wrench
to tighten. Finally use a wrench to hold the adapter
that’s connected to the water heater in place
and connect the end of the regulator hose to the
adapter using another wrench. After connecting it’s
imperative you inspect for gas leaks. See page 3 for
instructions on how to test for leaks.
Without compression tting
8b. Attach the gas regulator hose to the
LP tank and tighten the connection using a
wrench. Next attached the other end of the
regulator hose to the gas inlet pipe on the
water heater. Use a wrench to hold the gas
inlet pipe coming out of the water heater in
place and use another wrench to tighten the
hose connection to the gas inlet pipe. After
connecting it’s imperative you inspect for gas
leaks. See page 3 for instructions on how to
test for leaks.

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
10 11
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
Warning: This model is intended for recreational & portable use only. This
model CANNOT be permanently mounted or plumbed in any way.
1. Turn on incoming water supply. Ensure that you have adequate water pressure
of between 40-5O PSI / 2.7 - 3.4 bar.
2. Turn your water output device to its “o” position.
3. Turn the gas valve on the cylinder all the way open.
4. IF THE SMELL OF GAS IS DETECTED, TURN OFF THE GAS VALVE IMMEDIATELY!!
5. Set the water regulator knob on the face of the portable tankless water heater
to its highest setting.
6. Set the gas regulator knob on the face of the portable tankless water heater to
its minimum setting.
7. Turn on your water output device to the “on” position and adjust to the desired
water ow.
8. There will be a series of audible clicks and the burner will ignite. Should the
burner not ignite after 5 seconds, shut o and go to the “Trouble Shooting”
section.
9. Upon completion of use or storage, open the drain valve (ribbed cylindrical
stem next to the water input valve) to ensure draining of water.
10. Turn o your gas supply.
11. WARNING: If the outside temperature is around or below freezing (32 degrees
F, 0 degrees C), ensure that the drain valve is opened and water drained from the
portable tankless water heater after each use to avoid internal damage to the
water regulator. You will also need to unhook the outgoing water line to ensure
that any water in the heat exchanger is drained. Failure to properly drain your
portable tankless water heater will cause water damage which may or may not be
reparable. Please check the warranty information found on our website at www.
eccotemp.com/freeze for more information on freezing issues.
Use and Starting
Before going to the USE section:
Check around area for ammables, especially gasoline or other vapors which may ignite. The Exhaust
and top of the portable tankless water heater will get HOT! Make sure there are no foreign objects
around the portable tankless water heater or have fallen into the top.
Ensure that the unit is at least 60cm o the ground and equally removed from any inammable
materials. Always use the mounting tab on the back of the unit, this will ensure the proper 1cm spacing
between the unit and a wall or post sensitive to heat. Ensure that no obstruction or projection reduces
the space between the unit and the wall or post to less than 1cm.

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
10 11
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
The temperature of the outgoing water is dependent on the temperature of the
incoming water balanced with the amount of heat applied. Use extreme caution in
setting the outlet water temperature.
Adjustment
WARNING: THE PORTABLE TANKLESS
WATER HEATER IS CAPABLE OF PRODUCING
SCALDING WATER TEMPERATURES!
1. With the water regulator set to high, and the gas regulator set to
low, feel the outgoing water. This is the lowest setting available.
2. To initially raise the outgoing temperature, slowly turn the gas valve
towards maximum. Adjust slowly and check the temperature often.
There will be a slight delay between increasing the gas supply and the
increase in water temperature.
3. Should the outlet water temperature need to be higher, slowly reduce
the water ow regulator until desired temperature is reached.
(Warning: Do not alter or change this water heater’s original
temperature sensor)

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
12 13
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
Portable tankless water heater will not start – there are no audible clicks at startup:
a. The rst thing to check is to ensure that the incoming water on the “right” side of the portable
tankless water heater. If the incoming and outgoing are reversed, the portable tankless water heater
will not work. The incoming is on the far right and the outgoing is in the middle.
b. Check to make sure you have fresh batteries and they are installed in the correct position.
c. Number one reason that the portable tankless water heater does not ignite is that there is not
enough water pressure. You need a minimum of 10 PSI / 0.7 bar, sustained. Municipal water should
supply enough water pressure. Most 12/18/120/240 pumps well as long as they are capable of
delivering pressure of 10 PSI / 0.7 bar or greater.
ADJUSTMENT: Looking up at the bottom of the portable tankless water heater, you will see two “slits”
in the case where the front and back come together. Locate the water regulator where you will see
two Phillips head screws. Take the screw that is furthest on the right (larger screw) in about a ¼ or
½ turn. This will enable the portable tankless water heater to operate on a lower water pressure by
restricting ow.
NOTE: Before attempting to remove the cover, call technical support at the number on page 11.
d. A wire has become disconnected inside the portable tankless water heater during shipping. Make
sure the gas is OFF. The front cover is held by six screws, four on top, two on bottom. The knobs pull
o. All the wiring is done with push together plastic connectors. They are all visible without further
dismantling of the portable tankless water heater. It should be obvious when a wire has become
disconnected.
e. It is possible that some debris or epoxy might have entered the water regulator. Check to see if the
lter screen on the water inlet is clear of debris. You can also reverse the hookup by taking your water
source and hooking it up to the water outlet side and back ushing the system.
f. Propane gas cylinders sometimes are contaminated with air, especially new tanks upon their rst
lling. Cycle the portable tankless water heater turning o and on your output ow or similar. Does
not include a shower head.
Should a portable tankless water heater fail to light or stay lit after 10 cycles, please visit our helpdesk
located at gb.eccotemp.com for additional troubleshooting steps.
Portable tankless water heaters starts, then shuts o:
a. If the Rain cap is blocked, or not long enough, the portable tankless water heater will shut o after
a few minutes.
b. The portable tankless water heater requires a minimum of about 0.75 gallons per minute (2 liters)
and a minimum of about 20 PSI / 1.4 bar. Note: water pressure is at the lower end of operating
parameters. You will need a sustained water pressure of approximately 40-60 PSI / 2.7-4.1 bar for
adequate use if you are using a 12/18/120/240 volt pump. See ADJUSTMENT in previous section
above.
DO NOT RETURN TO STORE
Troubleshooting
Please contact us via the technical support information on page 14 if you
have any problems.

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
12 13
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
c. Out of, or low on gas. Propane gas cylinders sometimes are contaminated with air, especially new
tanks upon their rst lling. Cycle the portable tankless water heater on and o by using the shower
head switch several times (5) to purge the air from the gas. If this doesn’t clear the air then the tank
must be purged.
d. One of the ignition sensors is bent and/or too close to the burner. Look to ensure that the ignition
pins and the heat sensor are completely vertical and they do a 90 degree to the back of the box. If
they are not straight (i.e. a 45 degree angle) then you can straighten them with pliers.
e. The thermocouple is either too high or too low to complete the circuit. Check to ensure that the
thermocouple is ush with the hole in the heat exchanger.
f. The gas sensor wire (looks like a black ground wire on the gas regulator) ange might have come
loose or is no longer connected.
g. There is a faulty heat sensor. This is usually diagnosed by taking the front case o of the portable
tankless water heater and let it run. If it continues to operate, then one of the sensors and/or the wire
harness needs to be replaced. This may also be caused by insucient clearance on the back of the
portable tankless water heater where the majority of air intake is.
h. The valve on the propane tank should be all the way “Open”.
i. Fresh batteries are required for ignition spark. Make sure batteries are aligned in the proper
polarity (+/-).
The water does not get hot enough:
a. You are operating the portable tankless water heater above 4,000 feet / 1,000 meters. We only
recommend using it below elevations of 4,000 to 5,500 feet.
b. Look into the viewer panes (middle horizontal windows on the front cover) to see if there is a
blue ame. If the ame is yellow there could be a cracked gas regulator. Do Not Attempt to use the
portable tankless water heater and call us at the number on page 14.
Water is owing, but there is no hot water coming out:
a. Ensure that you have the incoming water supply and the outgoing water supply hooked up
properly. Your water supply should be attached to your incoming connection (located on the
far right) and the shower head should be attached to the outgoing water (located as the center
connection).
b. Ensure that you have adequate water pressure of at least 20 PSI / 1.38 bar, sustained.
c. Ensure that you have adequate gas in your propane bottle and that the LP regulator is threaded all
of the way on to the portable tankless water heater.
d. Fresh batteries are required for ignition spark. Make sure batteries are aligned in the proper
polarity (+/-).
If you are still having troubles or are on a modied water system, please visit our helpdesk located at
gb.eccotemp.com for additional troubleshooting steps.
The portable tankless water heater does nothing:
a. Ensure that you have your water source hooked up to the water inlet side (far right connection) and
the shower handle is hooked up on the water outlet side (middle connection).
b. Ensure that you have an adequate supply of propane.
c. Ensure that you have fresh batteries.
If you are still having troubles or are on a modied water system, please call techincal support at the
number listed on page 14.
Troubleshooting Continued...

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
14 15
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
Technical Support
For Technical Support Please Contact:
Eccotemp Systems LLC
Web: eu.eccotemp.com
E-mail: [email protected]
Phone: [phone]
Address: 315 - A Industrial RD.
Summerville, SC 29483
WARNING
Read the technical instructions before installation and use.
• Read instructions before use.
• For outdoor use only.
• Warning: Accessible parts may be very hot, keep young children away.
• Never move it during operation. Wait for 7 minutes after extinguishing the ame before moving.
• Check the gas type before you connect it to the water heater, improper gas will cause serious
danger.
• This heater is not to be used in wind speeds above 10 kph. The heater will extinguish at wind
speed above 10 kph. The feature is governed by safety tted to the appliance.
• This appliance must not be used in enclosed areas, for example under awnings or tents.
• The appliance must be hung correctly before use. Never use the appliance placed on the
ground.
• This appliance must be installed in accordance with any natural surrounding features to
protect it from direct winds.
0063-19
PIN NO: 0063CR7706
Technical Data

CE-L10 English
English CE-L10
Phone: [phone] | Email: [email protected] Phone: [phone] | Email: [email protected]
PLEASE NOTE: THIS MODEL IS NOT RECOMMENDED NOR HAS IT BEEN TESTED FOR ANY PERMANENT INSTALLATIONS. THIS MODEL
IS PART OF OUR PORTABLE SERIES AND NEEDS TO BE TAKEN DOWN AND STORED IN A WARM DRY PLACE AFTER EVERY USE.
THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
14 15
Support: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locatorSupport: Eccotemp.com/help-desk Shop Online: eu.eccotemp.com/products Store Locator: Eccotemp.com/locator
MODEL: CEL10
Country of Desnaon
BE, FR, GB,
GR, IE, IT, PT,
ES, CH
CY, CZ, DK, EE,
FI, LT, MT, NL,
NO, SK, SI, SE,
HU, BG, LV,
LU, RO
DE, AT, CH, SK PL
Appliance Categories I3+ I3B/P30 I3B/P50 I3B/P37
Type of gas G30/G31 G30 G30 G30
Supply pressure (mbar) 28-30/37 30 50 37
Min gas pressure (mbar) 20 25 42 25
Max gas pressure (mbar) 35 35 57 45
Injector Size (mm) 0.60 0.60 0.50 0.54
Applicable water pressure (MPa) 0.025-0.100
Nominal Heat Input (kW) 16 (kW)
Minimum Heat Input (kW) 8 (kW)
Nominal Useful Output (kW) 14 (kW)
Appliance Type A1
Load Prole M
Eciency Class A
Eciency % 77.6%
Annual Fuel Consumpon 6 GJ
Annual Electrical Consumpon 0 kwh
NOx 59 mg/kWh
Thermostat (max) 70°C
Sound Power Level 61dB