ECO-WORTHY CSP600 User manual

Contents
Important Safety Information
General Safety Information
Inverter safety
Bayttery Safety
General Information
Key feature
Installation
Operation
Maintenance
Troubleshooting
..............1
.................1
.....................................2
....................................2
............................5
..........................................3
...........................................5
............................................8
.......................................8
................................10
Location Recommendation
Wiring Step
Solar Panel Wiring
..........................................5
..................................................................6
.......................................................7

Important Safety Information
General Safety Information
This manual contains important safety, installation, and operating
instructions for the inverter.The following symbols are used throughout
the manual.
Warning:indicate a potential dangerous condition.Use extreme
caution when performing this task.
Caution:indicate a critical procedure for safe and proper operation of
the inverter.
Note:indicate a procedure or function that is important to the safe and
proper operation of the inverter.
Installation and wiring must comply with the Local and National Electric
Codes(NEC) and must be done by a certified technician.
Read all of the instructions and caution in the manual before beginning
the installation.
There are no serviceable parts for this inverter.do not disassemble or
attempt to repair the inverter.
Make sure all connections going into and from the inverter are
tight.There may be sparks when making connection,therefore,make
sure there are not flammable materials or gases near installation.
-1-

Inverter safety
Bayttery Safety
ALWAYS make sure inverter is OFF position and disconnect all AC and
DC.
Be careful when touching bare terminals of capacitors as they may
retain high lethal voltage even after power is removed.
Connecting when working on any circuit associated with the inverter-
when connecting battery terminals,ensure the polarity of the battery
connections is correct.Incorred polarity may cause permanent damage
to the unit.
Do not let the positive(+)and negative(-)terminals of the battery touch
each other.
Use only sealed lead-acid,flooed,gel,or LiFePO4 batteries which musst
be deep cycle.
Be careful when working with large lead acid batteries.Wear eye protec-
tion and have fresh water avaiable in case there is contact with the
battery acid.
Over-charging and excessive gas precipitation may damage the battery
plates and activate material shedding on them.Too high of an equalizing
charge or too long of one may cause damage. Please carefully review
the specific requirements requirements of the battery used in the
system.
Installation Safety The unit should be installed in a well-ventilat-
ed,cool,and dry envirment.Make sure the fans of the unit and the venti-
lation holes are not blocked.Do not expose the unit to rain,mois-
ture,snow,or liquids of any type.
-2-

General Information
Key feature
The Eco-worthy ALL-IN-ONE Pure Sine Wave Charge Inverter delivers
superior performance for Off-grid application，built-in solar charge
controller for your solar panel kit.
1.Built-in PWM charge controller.
2.SPWM pure sine wave output.
3.Dynamic LCD display and intelligent LEDs providing important
system information.
4.Manual ON/OFF switch controlling AC output.
5.Adjustable fan, efficient heat dissipation, extending the life of the
system.
6.Supports lead-acid battery and lithium battery types.
7.Solar protection：PV Short circuit protection, PV reverse protection,
PV overvoltage protection.
8.Battery protection：Undervoltage protection,overvoltage protection,
overload protection, short circuit protection, over heat protection.
-3-

Dimensions
① Solar input terminal ② Battery terminal ③ AC Outlets
-4-

Installation
Location Recommendation
Warning:Make sure inverter is in the off position before connecting
anything.
Caution:Do not over tighten the terminals.This could potentially
damage the unit.
1.Dry，cool，well-ventilated area
Inverters must be in an area where the fans are not blocked or where
they are not hit directly by the sun. They should be in an area free of any
kind of moisture and allow for clearance of at least 10” around the unit
to provide for adequate ventilation.
2.Protection against fire hazard The unit should be away from any flam-
mable material, liquids, or any other combustible material.
3.Close proximity to battery bank Prevent excessive voltage drop by
keeping the unit close to the battery bank and having a properly sized
wire going from the battery bank to the inverter.
4.Do not install the inverter in the same compartment as the battery
bankbecause it could serve as a potential fire hazard ！！
-5-
Wiring Step
First confirm that the AC output switch is turned off, then connect the
battery to the inverter, you need to distinguish 12V battery pack or 24V
battery pack, then connect the solar panels to PV input of terminal of
inveter, Be careful of the positive and negative poles. and turn on
the inverter Switch at last.

Rated Battery-
Discharge
Maximum
BatteryCharging
Recommended
wiring
Recommended
circuit breaker
Recommended
ring terminal
50A/62.5A 25A/50A 6mm2/10mm2 2P-63A/2P-120A 8.2/8.2mmΦ
-6-
Battery Wiring
Caution:Be careful of the positive and negative poles. Reversing the
poles may cause permanent damage to the inverter.
There may be a sparking occurring even the inverter is in the off posi-
tion. To minimize sparking, it is recommended that the user have the
appropriate size wire feeding into the solar inverters and/or install
an external fuse leading into the inverter.
The solar inverter takes a 12V(600W) or 24V(1500W) battery input to
operate. This will require combining 12V or 6V batteries in series to
achieve the minimum voltage DC requirement. It is recommended to
use battery cables with ring terminals. The ring terminals must be firmly
tightened and secured on the respective battery terminals to prevent
any excessive heating or resistance.
24V Battery pack 12V Battery pack

-7-
Recommended
wiring
Recommended
circuit breaker
Recommended
wiring
Bare wire
Maximum PV
Charging Current
4mm² 4.3mm/4.3mmΦ30A/50A
When combining panels in parallel it is recommended to use a combiner
box for safety and organizational precautions. This will require combin-
ing solar panels in series or series parallel to achieve the minimum
voltage DC requirement.
Caution:Connect the positive and negative PV wire to the respective
positive and negative PV terminal block on the solar inverter.
Solar Panel Wiring
24V Solar system 12V Solar system

-8-
Operation
Maintenance
LED Display Operation
Assuming all connections are correct and tightly secured, Locate the
power button on the solar inverter and press power switch to the ON
position. The following describes the basic operation of the solar invert-
er charger.
In order to maintain optimal long-term performance, it is recommended
to perform inspections of the following items twice a year.
1. Make sure that the air flow around the solar inverter is not blocked
and remove any dirt or debris from the radiator.
2. Check all terminals to see if there is corrosion, insulation damage,
high temperature or combustion / discoloration signs, tighten the termi-
nal screws.
(1) Solar input voltage
(2) Present battery capacity
(3)AC output voltage
(4)Load power

Input Voltage
Rated Power
Peak Power
Output Waveform
Maximum PV Array Open
Circuit Voltage
Maximum PV Array Wattage
Maximum Solar Charge Current
Battery Voltage Range
(BAT not included)
Solar Panel Input Voltage
Battery Charge Type
(BAT not included)
AC Output Voltage
AC Output Frequency
Output Wave
AC Output Sockets
Size
Weight
Model
12V
600W
1200W
500W
30A
12V
1
275*185*74
2.36Kg
24V
1500W
3000W
1200W
50A
24V
2
319*235*100mm
4.5Kg
120VAC±12V/230VAC ± 23V
50Hz/60Hz
Pure Sine Wave
600W 12V-
110V/230V
(CSP600)
Pure Sine Wave
10Vdc-15Vdc 20Vdc-30Vdc
PVM
Protect Function
PV-Reverse Input Protection、
PV-Short Circuit Protection、
Over-Heating Protection、
Over-Charge Protection
1500W
24V-110V/230V
(CSP1500)
-9-
Product specification

Fault code
1
2
4
8
16
32
64
28
56
12
Fault Name
Solar panels overvoltage
Generatrix overvoltage
Generatrix undervoltage
Overload
Slightly overload
Battery undervoltage
Battery overvoltage
AC output undervoltage
Short circuit of AC output
Over-temperature
Description
Overload
Slightly overload
DC-AC conversion failed
Load short/Overload
DC-DC voltage increase
system failed
long working time/Overload/
Cooling system
too many solar panels in series
wrong solar panel
reduce amount of solar panels in series
choose suitable panels
Low battery power
Overdischarge recovery time
charge your battery
Restart
Wrong battery type
Overcharge recovery time
choose right battery type
Restart
DC-DC voltage increase
system failed
Solution
repair
repair
reduce the load power
reduce the load power
load removing and restart
load removing and restart
failed
-10-
Troubleshooting