Toshiba TOSVERT VF-S11 User manual

E6581422③
TOSVERT VF-S11
Option Instruction Manual
CCL002Z
3. All information contained in this manual are subject to change without notice. Please
confirm the latest information on our web site "www.inverter.co.jp".
2. Read this manual before installing or operating the CC-Link option unit, and store it in a
safe place for reference.
1. Make sure that this instruction manual is delivered to the end user of the CC-Link option
for the VF-S11.
NOTICE

E6581422③
Safety precautions
On the inverter and in its instruction manual, important information is contained for
preventing injuries to users and damages to assets and for proper use of the device.
Read the instruction manual attached to the inverter along with this instruction manual for
completely understand the safety precautions, the symbols and indications shown below.
Please adhere to the contents of these manuals at all times.
Explanation of markings
Marking Meaning of marking
Warning Indicates that errors in operation may lead to death or serious injury.
Caution
Indicates that errors in operation may lead to injury (*1) to people or that these errors
may cause damage to physical property. (*2)
(*1) Such things as injury, burns or shock that will not require hospitalization or long periods of
outpatient treatment.
(*2) Physical property damage refers to wide-ranging damage to assets and materials.
Meanings of symbols
Marking Meaning of marking
Indicates prohibition (Do not do it).
What is prohibited will be described in or near the symbol in either text or picture
form.
Indicates something mandatory (must be done).
What is mandatory will be described in or near the symbol in either text or picture form.
Indicates warning.
What is warned will be described in or near the symbol in either text or picture form.
Indicates caution.
What the caution should be applied to will be described in or near the symbol in
either text or picture form.
－ 1 －

E6581422③
Limitation of use
Safety precaution
▼ Never use this unit with any device other than TOSVERT VF-S11 series inverters. Doing so may cause
an accident.
Handling in general
Warning
Disassembly
prohibited
▼ Never disassemble, modify or repair the product.
Disassembling the product may cause electric shocks, fire or injuries.
For repairs, call your sales/repair agency.
Prohibited
▼ Do not open the front cover on the inverter while the inverter power is on.
It may lead to electric shocks.
▼ Do not remove this option from VF-S11 while the power is on.
It may lead to electric shocks.
▼ Do not put or insert foreign objects such as waste cable, bars or wires into the product.
It may lead to electric shocks or fire.
▼ Do not splash water over the product, and do not wipe the body with a wet cloth.
It may lead to electric shocks or fire.
Mandatory
▼ Turn off input power before wiring and setting switches.
▼ Turn off the power immediately in case of any abnormalities such as smoke, smell or
abnormal noise.
Neglect of these conditions may lead to fire.
For repairs, call your sales/repair agency.
Transportation and installation
Warning
Prohibited
▼ Do not install or operate the inverter if it is damaged or any part of it is missing.
Operating a defective inverter may lead to electric shocks or fire.
For repairs, call your sales/repair agency.
▼ Do not put any flammable material near the product.
It may catch fire due to the product sparking in the case of a malfunction.
▼ Do not install in any location where the inverter may comes into contact with water or
other fluids.
It may lead to electric shocks or fire.
▼ When installing this option, be careful not to touch the leads from parts on the reverse
side of its circuit board.
It may lead to injury.
Mandatory
▼ Operate under the environmental conditions prescribed in the instruction manual.
Operations under any other conditions may lead to malfunction.
－ 2 －

E6581422③
Wiring
Warning
Mandatory
▼ Turn off input power before installing and wiring this option.
Wait at least 10 minutes and check to make sure that the charge lamp (VF-S11) is no
longer lit.
▼ Tighten the screws on the terminal block to the specified torque
(Refer to Section 3.2 and 3.3).
If the screws are not tightened to the specified torque, it may lead to fire.
▼ Electrical construction work must be done by a qualified expert.
Installation or connection of input power by someone who does not have that expert
knowledge may lead to fire or electric shocks.
Operations
Warning
Prohibited
▼ Do not touch switches when the hands are wet and do not try to clean the inverter
with a wet cloth.
It may lead to electric shocks.
▼ Do not pull on any cable itself.
It may lead to damage or malfunction.
Disposal
Caution
Mandatory
▼ For safety's sake, do not dispose of the disused inverter yourself but ask an industrial
waste disposal agent (*).
If the collection, transport and disposal of industrial waste is done by someone who is
not licensed for that job, it is a punishable violation of the law. (Laws in regard to
cleaning and processing of waste materials)
(*) Persons who specialize in the processing of waste and known as “industrial waste
product collectors and transporters” or “industrial waste disposal persons.”
Notes on use
Notes
▼ Avoid installing in a place where ambient temperature or/and humidity change sharply.
▼ Keep the communication cable separate and from the power cable of the inverter to
prevent the inverter from malfunctioning due to electromagnetic noise.
▼Please make grounding of a network SLD terminal different from grounding an inverter
and a motor. It becomes the cause of the malfunction by the noise.
▼ Insert a magnetic contactor or similar device between the inverter and the power
supply to ensure that power is turned off if an emergency stop command is entered
through the externally.
－ 3 －

E6581422③
Preface
Thank you for purchasing a “CC-Link Option (CCL002Z)” for TOSVERT VF-S11 inverter.
This option can connect with open field network CC-Link and data communications with the
CC-Link master through installing this option in the VF-S11 and using it. Besides this
instruction manual, the "CC-Link option Function Manual" is required to develop software
communicating with VF-S11. In such a case, please get in touch with our branch offices or
sales offices. ("CC-Link option Function Manual": E6581424).
▪CCL002Z Option Function Manual ························································E6581424
▪TOSVERT VF-S11 Instruction Manual ··················································E6581158
▪TOSVERT VF-S11 Communication Function Instruction Manual ·········E6581222
This manual is also aimed at the operator using "VF-S11 CC-Link option", so please use it for
future maintenance and inspection.
Explanation of model number of CC-Link option
CCL 002 Z - 0
Revision number
Cable length ( "Z" means 'without cable' )
Model number of CC-Link
Symbol of CC-Link
Accessory check list
CC-Link option is shipped together with the following items in the package. Contact your sales
agency if any of these is missing.
(1) VF-S11 CC-Link option (CCL002Z)............... 1 board
(Terminal connector : MC 1,5/5-ST-3.81)
: PHOENIX CONTACT.....1 piece
(2) Instruction manual for the VF-S11 CC-Link option
.....1 copy
English: E6581422
(This manual)
Manual
(3) Terminal name label (Male, Female) ....1 sheet each
(4) Cabling label ....1 sheet
(5) Type form label ....1 sheet
(6) Insulating sheet ....1 sheet
－ 4 －

E6581422③
－Table of contents －
1. Overview···················································································································································6
2. Name of functions of main parts ··············································································································6
2.1. Exterior features······························································································································6
2.2. RJ45 Connector for options (CN2) ·································································································7
2.3. Termination resistor selection switch (SW4)···················································································7
3. Installing the CCL002Z·····························································································································8
3.1. Description of terminals ················································································································10
3.2. Connection of control terminals ····································································································11
3.3. Connection of CC-Link cable ········································································································11
3.4. Wiring / Connection with the CC-Link master ···············································································12
4. Functions ················································································································································13
4.1. Initial setting ··································································································································13
4.2. Basic functions ······························································································································15
4.2.1. Run and frequency operation command ··············································································15
4.2.2. Monitor··································································································································15
4.2.3. Writing and reading the parameter·······················································································15
4.2.4. Disconnection error of network cable···················································································16
4.2.5. Error of communication between the CC-Link and inverter ·················································16
5. List of CC-Link data································································································································17
5.1. RX(Monitor), RY(Instruction)·········································································································17
5.2. RWr, RWw resistor························································································································18
5.3. Monitor code ·································································································································18
5.4. Instruction Codes ··························································································································19
5.5. Reply Code ···································································································································19
6. CC-Link local/Remote Operation ···········································································································20
7. Specifications ·········································································································································21
8. Warranty ·················································································································································21
－ 5 －

E6581422③
1.Overview
This option allows the VF-S11 inverter to be connected into a CC-Link network. CC-Link
supports a maximum of 42 nodes, allowing for the Master unit and this option is based on
CC-Link Ver.1.10.
The CCL002Z is able to operate RUN/STOP, monitor the status of the inverter, set the
inverter's parameter and etc. by the CC-Link master through installing the VF-S11. And it
can use different applications.
2.Name of functions of main parts
2.1. Exterior features
Here are the name and functions of the exterior components of the CCL002Z unit.
CC-Link connector
Phoenix Contact corp.
MC 1,5/5-ST-3,81
Input terminal
SINK/SOURCE select SW
V/I functions of VIA select SW
Optional RJ45 communication port
Termination resistors
select SW
Left : 110 ohm
Center : none
Right : 130 ohm
DA DB DG SLD FG
CN2 TB1
SW4
SW2-under
SW2-upper
Do not touch this switch.
It uses for only maintenance.
SW1 and SW3
RJ45 communication option can be
used. However it makes CC-Link
communication be disabled.
Status LED
CC-Link communication
L.RUN Light on during communication.
SD Light on during send the data of CC-Link.
Light on during received the data of
CC-Link.
RD
L.ERR Light on during communication error
－ 6 －

E6581422③
Behavior of LED
State of LED
L.RUN SD RD L.ERR Cause
z ~ ~ ~ Normal communication is made but CRC error has occurred
due to noise.
z ~ ~ { Normal communication
z ~ { ~ Hardware fault
z ~ { { Hardware fault
z { ~ ~ Cannot answer due to CRC error of receive data.
z { ~ { Data sent to the host station does not reach destination.
z { { ~ Hardware fault
z { { { Hardware fault (It is an unstable state by disconnection, etc.)
{ ~ ~ ~ Polling response is made but refresh receive is error in CRC.
{ ~ ~ { Hardware fault
{ ~ { ~ Hardware fault
{ ~ { { Hardware fault
{ { ~ ~ Data sent to the host station is error in CRC.
{ { ~ { There is no data sent to the host station, or data sent to the
host station cannot be received to noise.
{ { { ~ Hardware fault
{ { { { Cannot receive data due to break in the cable, etc.
{ { ~or { z Invalid baud rate or station number setting
z ~ ~ ~ Baud rate or station number changed during operation.
{ { { { WDT error occurrence (hardware fault), power off etc.
z: On {: Off ~: Flicker
2.2. RJ45 Connector for options (CN2)
During CC-Link communication, when a serial common option is connected to the
connector (CN2) for options, CPU of a CC-Link option board detects connection with a
connector, and stops the communication to the inverter. Then CC-Link network data are not
updated.
Moreover, the flag of RX(n+1)B [Remote READY] is set to “1” to “0”, and communication
with a CC-Link master station and this option (CCL002Z) is not performed.
And, the communication error trip time (f803) of an inverter is set up in addition to “0” at
the time of communication with a serial common option, and when the communication
timeout of the set-up time occurs, a trip (err5 occurs) is carried out.
2.3. Termination resistor selection switch (SW4)
By switching SW4 in the right-hand side of a CC-Link terminal, a termination resistor (Left:
110ohm, Right: 130ohm) can be selected. A termination resistor will not be connected if it
sets up in the center.
－ 7 －

E6581422③
3.Installing the CCL002Z
Install the CC-Link communication option to VF-S11 as follows.
(1) Turn off the input power of VF-S11 and wait for at least 10 minutes and then check that
the CHARGE lamp on VF-S11 is no longer lit.
(2) Open the VF-S11 front cover, remove the terminal board fixing screw and take off the
VF-S11 standard terminal board.
(Be careful not to lose the terminal board fixing screw when removed since it may be used
again.)
(3) Perform wiring an inverter before installing CC-Link communication option.
(4) Please attach the insulating sheet in VF-S11.
(Fix to the terminal board fixing screw hole and PWB catch pin.)
(5) Install the CC-Link communication option over the insulating sheet and secure it with
the board fixing screw (tightening torque of M3 tapping screw: 0.7 to 0.8Nm).
(6) Stick the cabling label for CC-Link communication option on the standard cabling label
stuck on the reverse side of the VF-S11 front cover. And stick the CC-Link
communication option type form label near the standard nameplate. (Be careful not to
cover slits on the VF-S11 enclosure.)
N.B.: To install or remove the terminal board, make it slide in or out in parallel with board.
VF-S11 unit (Under 3.7kW) Board catching pin
Terminal board fixing scre
w
(M3 screw tightening torque: 0.7 to 0.8Nm)
DA DB DG SLD FG
DA DB DG SL D FG
Cabling label position
Example
CC-Link communication
option (CCL002Z)
CC-Link terminal label(attached)
Stick the label to the CC-Link terminal.
DA DB DG SLD FG
DA DB DG SLD FG
RS4003Z
CCL002Z
Type form label(attached)
Stick the CCL002Z type form label like
bellow figure.
Board fixing screw hole
VF-S11 nameplate
CCL002Z
Insulating sheet (attached)
(It is not necessary to
cover the 5.5 to 15kW
model with an insulating
sheet.)
VF-S11 Standard terminal board
－ 8 －

E6581422③
VF-S11 unit (Over 5.5kW)
Terminal board fixing scre
w
Warning
Mandatory
▼Be sure to attach an attached insulating sheet.
It becomes the case of failure when not attaching.
(For the 5.5 to 15kW model, it is unnecessary.)
Board fixing screw hole
(M3 screw tightening torque: 0.7 to 0.8Nm)
Board catching pin
Cabling label position
Example
DA DB DG SLD FG
DA DB DG SLD FG
DA DB DG SLD FG
DA DB DG SLD FG
VF-S11 Standard terminal board
CC-Link communication
option (CCL002Z)
CC-Link terminal label(attached)
Stick the label to the CC-Link terminal.
RS4003Z
Type form label(attached)
Stick the CCL002Z type form label like
bellow figure. CCL002Z
VF-S11 nameplate
CCL002Z
－ 9 －

E6581422③
3.1. Description of terminals
<Control terminals specification>
Te r m i n a l
S
y
mbol
Input/
Output Function Electrical specifications
F
This terminal is Multifunction programmable contact input.
Shorting across F-CC causes forward rotation; open causes
deceleration stop. (Across ST-CC is short state.)
R
Input This terminal is Multifunction programmable contact input.
Shorting across R-CC causes reverse rotation; open causes
deceleration stop. (Across ST-CC is short state.)
RES Input
This terminal is Multifunction programmable contact input.
Shorting and then opening RES-CC cancels the status held by an
inverter protective function. When the inverter is operating normally,
shorting and then opening RES-CC produces no effect.
Voltage free contact
input.
24Vdc-5mA or less
*Sink/source
selectable with SW2.
VIA Input This terminal is Multifunction programmable contact input.
Standard default settin
g
: 0 to 10Vdc input and 0 to 60Hz frequenc
y
.
10Vdc
(
Internal impedance:
30k ohm)
P24 Output 24Vdc power output 24Vdc-50mA
OUT
Multifunction programmable open collector output. Standard default
settings detect and output speed reach signal output frequencies.
Multifunction output terminals to which two different functions can
be assigned.
NO
Output
The NO terminal is an isolation output terminal. It is insulated from
the CC terminal.
Open collector output
24Vdc-50mA
To output pulse trains,
a current of 10mA o
r
more needs to be
passed.
Pulse frequedncy
range:
38 to 1600Hz
CC
Common to
input/
output
Analog input/output signal equipotential (0V) terminal for the control
circuit.
DA
DB
These terminals are for communication of CC-Link. DA terminal is
“+” and DB terminal is “–“.
DG This is signal ground terminal. Connect to the DG terminal of the
Master.
SLD This is a terminal for the shield cable. This terminal is connected to
FG terminal inside the board.
FG
Te r m i n a l s
for CC-Link
communica
tion
This is a terminal for ground. Connect to the ground.
[Internal circuits]
Refer to the instruction manual of VF-S11 (E6581158) about internal circuits of input/ output
terminals other of F, R terminals.
Warning
Prohibited
▼Do not change switches settings while the power on.
It may lead to electric shocks or damage.
Mandatory
▼Turn off the motor operation signals before setting the parameter and the
switch, when changing the VIA function. Otherwise, the motor may suddenly
start and that may result in injuries.
－ 10 －

E6581422③
3.2. Connection of control terminals
Observe the following when wiring.
▼Keep the control signal cables 20cm or more separate from the power cables to prevent
from malfunctioning due to electromagnetic noise.
▼Use 0.14 to 1.5mm2solid/stranded wire (AWG 28 to 16) for control cables.
*Provide an inter-lock system stated in below, when using a programmable controller
that has the open collector output.
When the programmable controller is turned off with the inverter is on, the difference
between each control power potential will cause wrong signals to the inverter as shown
in below figure. Provide an inter-lock so that the programmable controller cannot be
turned off when the inverter power is alive.
COM
+24V
Inverter
internal +24V
External
+24V supply
VF-S11 + CCL002ZProgrammable controller
Input terminal
Fuse blowout
detection
circuit
Fuse
• Recommended tightening torque : 0.22 N･m
• Skin length : about 5mm
• Recommend screwdriver : A small flat-blade screwdriver
(tip thickness 0.4mm, full length 2.5mm)
3.3. Connection of CC-Link cable
If use other than the CC-Link dedicated cable, the performance of the CC-Link system is
not guaranteed. Please ask a manufacture given in the product catalog of CC-Link
association issue, or the "product information" on a CC-Link association homepage
(http://cc-link.org/) about the details of the CC-Link dedicated cable.
Please use the recommended CC-Link dedicated cable. And strip the cable sheaths and
twist the wires. If the sheath was stripped too long, the cable may contact with the adjacent
cable and cause a short circuit. If the sheath was stripped too short, the cable may be not
connected.
• Recommend screwdriver ：A small flat-blade screwdriver
(tip thickness 0.4mm, full length 2.5mm)
• Recommended tightening torque ：0.22 to 0.25 N･m
• Skin length ：about 7mm
－ 11 －

E6581422③
7mm
* Fix the communication cables after wiring.
* If take care of the wire end, use below parts.
Manufacture : Phoenix contact corp.
Part Number : AI 0,5-8 WH (connect one wire)
Part Number : AI-TWIN2x0,5-8 WH (connect two wires)
Length : 8mm
3.4. Wiring / Connection with the CC-Link master
The example of wiring/connection with the CC-Link master unit is shown in the following
figure.
CC-Link
Master Unit
*1
DA
DB
DG
SLD
FG
CCL002Z
DA
DB
DG
SLD
FG
Inverter
VF-S11
R/L1
S/L2
T/L3
U/T1
V/T2
W/T3 IM
Motor
The example of wiring with the inverter VF-S11
*1: As for master station, when use the Mitsubishi Electric An series, the recommended version is "LS" or later.
• Connection of Several Inverters
Factory Automation can be applied with several inverters which share CC-Link system as
a remote device station, and are controlled and monitored by PLC user programs.
* Communication terminal DA, DB
Set up the network using shielded twisted pair cable.
* Communication terminal DG
* Shield connection terminal SLD
Please connect the shield line of the dedicated CC-Link cable with the SLD
terminal.
* Connection of the frame ground terminal FG
Grounding resistance is 100 ohm max.
* Termination resistor
Switch of the SW4 and choose a 110ohm-termination resistor.
(Note: Please use 130 ohm, 1/2W resistors when use the high performance CC-Link
dedicated cable.)
－ 12 －

E6581422③
DA
DB
DG
SLD
FG
DA
DB
DG
SLD
FG
Master unit Inverter
CC-Link dedicated
cable
CC-Link dedicated
cable
Te rmi na t i on
resistor
DA
DB
DG
SLD
FG
Inverter
Te rmi na t i on
resistor
110 ohm, 1/2W
(130 ohm, 1/2W) 110 ohm, 1/2W
(130 ohm, 1/2W)
Ground
(100 ohm or less)
* Maximum number of units connected to one master station is 42 units (when only
inverters are connected).
* If any other units are included, the number of occupied stations depends on the unit. So
the connectable number of units is different.
4.Functions
This option is a communication interface unit that allows the PLC program to operate,
monitor and set the parameter of the inverter as a remote station of CC-Link. It is able to
communicate with a maximum speed of 10Mbps not only transmitting bit data but also by
word data.
4.1. Initial setting
Set the following parameters of the inverter before begin the communication.
If not change settings, cannot communicate and it becomes the cause of causing malfunction.
Moreover, power supply reset is needed for confirming setting change of a parameter.
List of CC-Link parameter
Title Communication
No. Adjustment range Default User setting
f800
0800
Communication rate
0: 1200bps 1: 2400bps 2: 4800bps
3: 9600bps 4: 19200bps
3 4
(Recommended)
f801
0801
Parity
0: NON (No parity)
1: EVEN (Even parity)
2: ODD (Odd parity)
1 1
f803
(*1)
0803
Communication error trip time
0: (disable)
1-100s
0 1 or more
f805
0805
Communication waiting time
0.00-2.00s 0.00 –
f829
0829
Selection of communication protocol
0: TOSHIBA inverter protocol
1: Modbus RTU protocol
0 0
(*2)
f870
0870
Block write data 1
0: No selection
1: Command 1
2: Command 2
3: Frequency command
4: Output data on the terminal board
5: Analog output for communications
0 1
(*2)
－ 13 －

E6581422③
f871
0871
Block write data 2
Ditto
0 3
(*2)
f875
0875
Block read data 1
0: No selection
1: Status information
2: Output frequency
3: Output current
4: Output voltage
5: Alarm information
6: PID feedback value
7: Input terminal board monitor
8: Output terminal board monitor
9: VIA terminal board monitor
10: VIB terminal board monitor
0 1
(*2)
f876
0876
Block read data 2
Ditto
0 2
(*2)
f877
0877
Block read data 3
Ditto
0 8
(*2)
f878
0878
Block read data 4
Ditto
0 3
(*2)
f879
0879
Block read data 5
Ditto
0 4
(*2)
f880
0880
CPU software version of CCL002Z
X . XX Version . Revision
*Note that it cannot use it as an original free
note.
– –
f890
0890
Station Number1-64
(It becomes invalid when a setting value is
outside the setting range.)
0 (*2)
f891
0891
CC-Link communication rate
0: 156kbps 1: 625kbps 2: 2.5Mbps
3: 5Mbps 4: 10Mbps
(It becomes invalid when a setting value is
outside the setting range.)
0 4
(Recommended)
(*2)
f892
0892
Inverter operation at disconnection
0: inverter stop, communication command,
frequency mode open
1: None
2: Deceleration stop
3: Coast stop
4: Emergency stop
5: Preset speed operation selection
(It operates on the preset speed frequency
set up by f893)
(A setting value is operation at the time of “0”
more than “6.”)
0 –
f893
0893
Preset speed operation selection
0: None
1 to 15: preset speed operation
(A setting value is operation at the time of "0”
more than “16.”
0 –
f894
0894
Disconnection detection extended time
0.0 to 100.0s Setting unit: 0.1s
(The value set up is set to “100.0” when a
setting value is “100.1” or more)
0 –
*1) Since the trip of the inverter is not occurs when this parameter is set as “0: disable”, and error in CPU etc.
occur. Set up more than “1” is recommended. Refer to the instruction manual [VF-S11 communication
instruction] (E6581222) for the detail.
*2) Set these parameters of the inverter before begin the communication.
If not change settings, cannot communicate and it becomes the cause of malfunction.
－ 14 －

E6581422③
4.2. Basic functions
This clause shows the basic function of this CC-Link option using by CC-Link
communication.
4.2.1. Run and frequency operation command
The PLC program can operate the inverter to run, stop, set the operation frequency and
change the parameters.
If the PLC controls these operations, select the command mode and the frequency setting
mode.
The parameter setting of the inverter
Command mode selection
CMOD: The inverter does not have this function. Turn on RYnB and set it as
CC-Link priority.
Frequency setting mode selection
FMOD: 4[Communication option input] (Factory setting: 0)
4.2.2. Monitor
It is able to monitor the status of the inverter.
Set the monitor code to RWwn and turn RYnC on. The data is stored in the buffer memory
of the PLC.
* "n" is depend on the station number.
• Refer to "Section 5 List of CC-Link data" about the monitor code and unit.
4.2.3. Writing and reading the parameter
The PLC can read, write the inverter parameters and reset the inverter.
Set the command code to RWw(n+2) (set the write data to RWw(n+3) if necessary) and
turn RYnF (instruction code execution request) on. The inverter performs processing
corresponding to the command code, and return the response data, the read out data and
RXnF (instruction code execution completion).
• Refer to the "CC-Link Option Function Manual E6581424" for the command code, the unit
of the data, and the setting range.
－ 15 －

E6581422③
4.2.4. Disconnection error of network cable
Disconnection of a CC-Link network cable, operation at the time of the abnormalities in
communication, detection, etc. are set up with the following parameter of the VF-S11.
f892: [Inverter operation at disconnection]
Default: 0
0: Inverter stop, communication command, frequency mode open
1: None (continued operation)
2: Deceleration stop
3: Coast stop
4: Emergency stop
5: Preset speed operation (by f893 でsetting)
• The action of the inverter when the communication error occurred can be specified.
f893: [Preset speed operation selection]
Default: 0
0: None
1 to 15: Preset speed operation (by parameter setting)
f894: [Disconnection detection extended time]
Default: 0 Setting unit: 0.1s
0.0 to 100.0s
• The waiting time from when a network error occurs to when a communication error can
be adjusted. When normal communication returns during the set time, a communication
error is not displayed and operation is continued.
4.2.5. Error of communication between the CC-Link and inverter
The error of communication between the CC-Link and the inverter are detectable with the
“communication error trip time” of f803. When the communication of the CC-Link option
and the inverter is not able within the time f803, the inverter occurs err5
(communication is unusual) trip.
Moreover, since the trip of the inverter is not occurs when this parameter is set as “0:
disable”, and error in CPU etc. occur. Set up more than “1” is recommended.
－ 16 －

E6581422③
5.List of CC-Link data
This option occupies one station area of the buffer memory of the PLC.
5.1. RX(Monitor), RY(Instruction)
List of remote I/O
Inverter (Slave) -> PLC (Master) PLC (Master) -> Inverter (Slave)
Device No. Signal Device No. Signal
RXn0 Forward running RYn0 Forward rotation command
RXn1 Reverse running RYn1 Reverse rotation command
RXn2 Output terminal function
selection 1 (RY) RYn2 Preset speed operation frequencies 1
RXn3 Output terminal function
selection 2 (OUT) RYn3 Preset speed operation frequencies 2
RXn4 Output terminal function
selection 3 (FL) RYn4 Preset speed operation frequencies 3
RXn5 Failure FL RYn5 Preset speed operation
frequencies 4
RXn6 PI control OFF RYn6 PI control
RXn7 Acceleration/deceleration
pattern selection (1 or 2) RYn7 Acceleration/deceleration pattern selection (1 or 2)
RXn8 Reserved RYn8 Emergency stop
RXn9 Coast stop (ST = OFF) RYn9 Coast stop command
RXnA Alarm RYnA Frequency priority selection
RXnB Failure RYnB Command priority selection
RXnC Monitoring RYnC Monitor command
RXnD Frequency setting completion RYnD Frequency setting command
RXnE Reserved RYnE Reserved
RXnF Instruction code execution
completion RYnF Instruction code execution request
RX(n+1)0 RY(n+1)0
RX(n+1)1 RY(n+1)1
RX(n+1)2 RY(n+1)2
RX(n+1)3 RY(n+1)3
RX(n+1)4 RY(n+1)4
RX(n+1)5 RY(n+1)5
RX(n+1)6 RY(n+1)6
RX(n+1)7 RY(n+1)7
RX(n+1)8 RY(n+1)8
RX(n+1)9
Reserved
RY(n+1)9
Reserved
RX(n+1)A Error status flag RY(n+1)A Error reset request flag *2
RX(n+1)B Remote station ready RY(n+1)B
RX(n+1)C RY(n+1)C
RX(n+1)D RY(n+1)D
RX(n+1)E RY(n+1)E
RX(n+1)F
Reserved
RY(n+1)F
Reserved
"n" is depend on the station number.
*1 The reserved input signal should be set OFF ("0").
*2 A reset request is during switched ON.
－ 17 －

E6581422③
5.2. RWr, RWw resistor
RWr . RWw (Default value = 0)
Inverter →PLC (RWr) PLC →Inverter (RWw)
Address Contents Address Contents
RWr n First monitor value RWw n Monitor code (first and second)
RWr n+1 Second monitor value (output frequency) RWw n+1 Set frequency
RWr n+2 Reply code RWw n+2 Instruction code
RWr n+3 Read data RWw n+3 Write data
"n" is depend on the station number.
5.3. Monitor code
Divide the monitor code (RWw n) into half and select the first monitor data (RWr n) from the
lower 8 bits and the second monitor data (RWr n) from the higher 8 bits.
(Example) When output voltage is selected for the first monitor and output torque is
selected for the second monitor. -> The monitor code is 0703H.
RWw n Monitor code
the higher 8 bits the lower 8 bits
Second monitor description First monitor description
* The hexadecimal value attaches and expresses "H" to the end of a number.
Monitor code (When an invalid monitor code is set up, monitor value fixes to 0.)
Code Number Second Monitor Description
(the higher 8 bits)
First Monitor Description
(the lower 8 bits) Unit
00H Output frequency(Second monitor
only) None monitor (Monitor value is 0) 0.01Hz
01H Output frequency Output frequency 0.01Hz
02H Output current Output current 0.01A
03H Output voltage Output voltage 0.1V
04H None monitor (Monitor value is 0) None monitor (Monitor value is 0) –
05H Frequency command value Frequency command value 0.01Hz
06H None monitor (Monitor value is 0) None monitor (Monitor value is 0) –
07H Output torque Output torque 0.1%
08H DC voltage DC voltage 0.1V
09H PBR load factor PBR load factor 0.1%
0AH Motor overload factor (OL2 data) Motor overload factor (OL2 data) 0.1%
0BH, 0CH None monitor (Monitor value is 0) None monitor (Monitor value is 0) –
0DH Input power Input power 0.01kW
0EH Output power Output power 0.01kW
0FH Input terminal information Input terminal information –
10H Output terminal information Output terminal information –
11H Output current (% monitor) Output current (% monitor) 0.1%
12H Exciting current Exciting current 0.01A
13H None monitor (Monitor value is 0) None monitor (Monitor value is 0) –
14H Cumulative operation time Cumulative operation time 1hr
15H, 16H None monitor (Monitor value is 0) None monitor (Monitor value is 0) –
17H Accumulation power supply ON time Accumulation power supply ON time 1hr
18H Motor overload factor Motor overload factor 0.1%
19H Integral input power Integral input power 1kWh
1AH Integral output power Integral output power 1kWh
1BH Analog input monitor (VIA) Analog input monitor (VIA) –
1CH Analog input monitor (VIB) Analog input monitor (VIB) –
1DH to 20H None monitor (Monitor value is 0) None monitor (Monitor value is 0) –
21H Torque current Torque current 0.1%
22H, 23H None monitor (Monitor value is 0) None monitor (Monitor value is 0) –
24H PID feedback value PID feedback value 0.01Hz
25H to 2FH None monitor (Monitor value is 0) None monitor (Monitor value is 0) –
－ 18 －

E6581422③
5.4. Instruction Codes
Code No. Contents Description
1003H Command mode selection read
2003H Command mode selection write
0 : Terminal board
1 : Operation panel
1004H Frequency setting mode
selection read
2004H Frequency setting mode
selection write
0 : Built-in potentiometer
1 : VIA
2 : VIB
3 : Operation panel
4 : Serial communication
5 : UP/DOWN communication
6 : VIA + VIB (Override)
0072H Special monitor 0000H to FFFFH : Monitor value selected after choosing
instruction code 00F3H.
0073H read Special monitor code read Read the content which was monitored by special monitor.
00F3H write Special monitor selection Select the monitor code of special monitor.
0074H Trip history No.1, No.2 read
0075H Trip history No.3, No.4 read Read the No.1(latest) to No.4(oldest) trip records.
006DH Frequency command value (RAM)
read Read the frequency command value (RAM).
00EDH Option frequency command value
(RAM) write * Write the option frequency command value (RAM). *
00F4H Trip history clear 9696H : Clear all trip history.
00FCH Parameter all clear
9696H : Clear all parameters. (Parameters other than
proofread values are made into factory default
settings.)
00FDH Inverter reset 9696H : Reset the inverter. (This command is invalid when
the inverter is normal.)
1000H to
1999H
(1000H to
1F99H)
Read parameters (RAM)
To read parameters F000 to F912, add the triple figures that
follow Fxxx to 1000H. (Ex: F912 -> 912 + 1000 = 1912)
No error occurs when you select 1A00 to 1F99. Because
these parameters are for maintenance.
2000H to
2999H Write parameters (EEPROM&RAM) To write parameters F000 to F912, add the triple figures
that follow Fxxx to 2000H.
* The writing of frequency instructions serves as only writing to RAM area.
Note: The frequency value setting when power off and on or reset the inverter, the frequency setting is
reset (0Hz).
5.5. Reply Code
When executing the frequency setting (RYnD) or instruction code execution (RYnF), check
the reply code (RWr (n+2)) in the remote register after execution.
Reply code
Data Item Detailed contents
0000H Normal (No error) Normal completion of instruction code execution
0001H Write error Execution error.
(Write protected during operation)
0002H Parameter selection error Unregistered code number was set.
0003H Setting range error Set data is outside the setting data range.
－ 19 －