eCOUNT aFLAT Series User manual

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
aFLAT-series
Flat Panel Controller
CRTtoLCD-71

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Contents
Contents
GENERAL INFORMATION AND IMPORTANT NOTES............................ 2
1.1 User Information ......................................... 2
1.2 Trademarks............................................. 2
1.3 General................................................ 2
1.4 Warranty............................................... 2
2. INTRODUCTION .................................................... 3
TECHNICAL INFORMATION SUMMARY...................................... 3
3. CONFIGURATION ................................................... 5
3.1 Backlight adjust configuration JP600........................... 5
3.2 Backlight ON configuration JP601............................. 5
3.3 Backlight adjust level configuration JP602....................... 6
3.4 Backlight voltage configuration JP602.......................... 6
3.5 Panel voltage configuration JP602 ............................ 6
3.6 Display port power configuration JP500 ........................ 6
3.7 Serial port configuration JP1300 ............................. 7
4. CONNECTORS ..................................................... 8
4.1 SVHS Video Input CN300 .................................. 8
4.2 Composite video input CN301 ............................... 8
4.3 YUV analog input CN302 (optional) ........................... 8
4.4 VGA/RGB analog Input CN303 (optional) ....................... 8
4.5 DVI-I input connector CN400 ................................ 9
4.6 Display Port connector CN500 ............................... 9
4.7 JILI40-Interface CN601 ................................... 10
4.8 JILI30-Interface CN603 ................................... 11
4.9 Backlight Connector CN7001 ............................... 12
4.10 Audio input/output CN700 (optional) .......................... 12
4.11 IR input CN800 ......................................... 12
4.12 OSD keypad connector CN801.............................. 12
4.13 ADC Input Connector CN900 (Light Sensor Input) ................ 13
4.14 GPIO Connector CN 801 .................................. 13
4.15 RS232 Serial OSD connector CN1300 ........................ 13
4.16 USB Serial OSD connector (optional) ......................... 13
4.17 DC Power Supply 4-Pol. CN1500 ............................ 14
4.18 DC Power Supply DC-Jack CN1501 .......................... 14

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Contents
5. ON SCREEN DISPLAY............................................... 15
6. TECHNICAL SPECIFICATIONS ........................................ 16
7. SUPPORTED VIDEO MODES.......................................... 18
8. LAYOUT / SCHEMATICS ............................................. 19
TECHNICAL SUPPORT ................................................. 21
9. REVISION HISTORY ................................................ 21

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
General information and important notes
2
General information and important
notes
1.1 User Information
Copyright 2014 by ECOUNT Technology GmbH.
In this document ECOUNT Technology GmbH will also be referred to by the short form
“eCOUNT”.
The information in this document has been carefully checked and is believed to be accurate
and reliable. However, no responsibility is assumed for inaccuracies. Furthermore, ECOUNT
Technology GmbH reserves the right to make changes to any portion of this manual to
improve reliability, function or design. ECOUNT Technology GmbH does not assume any
liability for any product or circuit described herein.
1.2 Trademarks
AT and IBM are trademarks of International Business Machines.
XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines
Corporation.
Microsoft is a registered trademark of Microsoft Corporation.
Intel is a registered trademark of Intel Corporation.
All other products and trademarks mentioned in this manual are trademarks of their
respective owners.
The reproduction, transmission or use of this document or its contents is not permitted
without expressed written authority.
Offenders will be liable for damages. All rights created by patent grant or registration of a
utility model or design, are reserved.
1.3 General
For the circuits, descriptions and tables indicated no responsibility is assumed as far as
patents or other rights of third parties are concerned.
The information in the Technical Descriptions describes the type of the boards and shall not
be considered as assured characteristics.
The reproduction, transmission or use of this document or its contents is not permitted
without express written authority. Offenders will be liable for damages. All rights, including
rights created by patent grant or registration of a utility model or design, are reserved.

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
General information and important notes
2
1.4 Warranty
Each board is carefully and thoroughly tested before being shipped. If, however, problems
should occur during the operation, please check your user specific settings of all boards
included in your system. This is often the source of the fault. If a board is defective, it can be
sent to your supplier for repair. Please take care of the following steps:
- The board returned should correspond to the factory default settings since a test is
only possible under these settings.
- In order to repair your board as fast as possible, we require some additional
information from you. Please fill out the attached Repair Form and include it with the
defective board.
- If possible, the board will be upgraded to the latest version without additional cost.
- Upon receipt of the board, please be aware that your user specific settings are
changed during the test.
Within the guarantee, the repair is free as long as the guarantee conditions were kept. If no
fault has been found, you will be charged with the test cost due to the high test expenditure.
Repairs outside of the guarantee will be charged.
This ECOUNT Technology GmbH product is warranted against defects in material and
workmanship for our guaranteed warranty period from the date of shipment. During the
warranty period, ECOUNT Technology GmbH will, at its option, either repair or replace
products which prove to be defective.
For warranty service or repair, the product must be returned to a service facility designated
by ECOUNT Technology GmbH.
The foregoing warranty shall not apply to defects resulting from improper or inadequate
maintenance or handling by buyer, unauthorized modification or misuse, operation outside of
the environmental specifications for the product, or improper installation or maintenance.
ECOUNT Technology GmbH will not be responsible for any defects or damages due to a
faulty ECOUNT Technology GmbH product other than the products supplied by ECOUNT
Technology GmbH.

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Introduction
3
2. Introduction
The CRTtoLCD-71 is a highly integrated TFT panel interface controller, which allows an
easy adaptation of standard video input sources like S-video, composite video, DVI or
analog RGB to a digital TFT panel. The CRTtoLCD-71 only needs one single 12V power
supply and incorporates all needed functionality to build up a full featured TFT monitor. The
card generates the necessary power sequencing for the flat screen. The highly flexible
architecture of the CRTtoLCD-71 panel interface allows adapting nearly any available TFT
panel. Therefore a variety of panel adapters and programming are available on request.
Technical Information Summary
FLEXIBLE DIGITAL AND ANALOG CAPTURE
•Integrated dual 10-bit triple ADCs with capture up to 205 MHz
•Input resolution support up to UXGA@75 Hz/WUXGA@60 Hz
•Composite-Sync and Sync-on-Green (SOG) support
•Instant Auto™ for automatic phase and clock adjustment
•4:4:4/4:2:2/CCIR656/601 30/24/16/8-bit digital input port
INTEGRATED HDMI 1.3 RECEIVER
• Integrated multi-mode HDMI 1.3
• Front-end multiplexer supports two physical input ports
• 1080p HDMI capture support
• HDCP 1.2a content protection with integrated key storage
• xvYCC support based on IEC61966-2-4 color standard
• Deep Color and Wide Gamut support: 12-bit HDMI input at YCC 4:4:4
INTEGRATED 3D VIDEO DECODER
• Single 3D Adaptive Comb Filter for Luma–Chroma separation
• Supports Composite, S-Video, and Component SD and HD video input signals
• Macrovision®b and VCR trick mode support
INTEGRATED DISPLAYPORT 1.1 RECEIVER
• DisplayPort interconnectivity provides very high bandwidth compared to conventional
digital interfaces
• DisplayPort link comprising of 4 main lines and 1 auxiliary channel
• WUXGA capture support
INTEGRATED AUDIO PROCESSING
• 2 Stereo (L/R) analog inputs
• Additional and separate audio inputs for HDMI SPDIF
• Outputs include 2 analog DACs and SPDIF
• Worldwide multi-standards audio support
• Integrated I2S Audio Delay to exact audio and video synchronization
• Supports 5.1 analog/digital output stream (Left, Center, Right, LS, RS + LFE)
FAROUDJA REALCOLOR®
• Faroudja RealColor® provides true 10-bit color processing
• Active color management with overlapping regions
• Adaptive Contrast Control
• Integrated noise filter to eliminate contrast noise

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Technical Information Summary
4
FAROUDJA DCDI CINEMA® FORMAT CONVERSION
• Low Angle De-interlacing processing
• Per Pixel Motion Adaptive De-interlacing (MADi) up to 1080i format
• Format conversion up to 1080p resolutions
• Adaptive 3D/TNR Noise Reduction
PICTURE-IN-PICTURE (PIP)
• Programmable PIP channel horizontal and vertical filter coefficients
• Flexible PIP, PBP, and POP support capability (Video, Graphics)
• DCDi Edge® processing for second channel window
FAROUDJA® TRUELIFE™ VIDEO ENHANCER
• High performance programmable sharpening filters with Noise Coring
• Programmable Main channel horizontal and vertical filter coefficients
• Non-linear Chroma and Luma enhancement
DDR2 MEMORY CONTROLLER
• 32-bitDDR2 memory I/F support
ON-CHIP MICROPROCESSOR AND OSD CONTROLLER
• Integrated x186-based microprocessor
• General Purpose Inputs/Outputs (GPIOs)
• 2-wire serial master bus interface for external device control
• Integrated I/R decoder and low bandwidth ADC
• Advanced bit-mapped OSD controller
OUTPUT FORMATS
• Dual-channel/single-channel 18/24/30-bit LVDS transmitters
• Single-channel 24/30-bit TTL output
• Adaptive Contrast Ratio (ACR) control for automatic, intelligent backlight adjustments
Display Interface Features :
• Control signal generation for backlight inverter
• backlight dimming support (PWM and voltage controlled )
• Voltage generation and power sequence control for panel
• Flat screens can be used with either 3.3V, 5V or 12V.
• JILI30/40/50 (LVDS) panel interface (one and double port up to 30 Bit)
Operating Features:
- 5 button user interface (OSD Keypad)
- On Screen Display (OSD) control for all features
- Full multi sync capable
- VESA DPMS and DDC2B support
- Single voltage supply (+12V/24V DC )
- Dynamic Power Management for minimal power consumption via DPMS
- No software drivers needed!

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Configuration
5
3. Configuration
3.1 Backlight adjust configuration JP600
Pin
Description
O
1
-
2
PWM Adjust
O
2
-
3
Linear Adjust
O
Never unplug/replug this while in use
3.2 Backlight ON configuration JP601
Pin
Description
O
1
-
2
Active high BLON
O
2
-
3
Active low BLON
O
Never unplug/replug this while in use

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Configuration
6
3.3 Backlight adjust level configuration JP602
Pin
Description
O
1
-
2
5V Adjust
O
2
-
3
12V Adjust
O
Open
3.3V Adjust
Never unplug/replug this while in use
3.4 Backlight voltage configuration JP1500
Pin
Description
O
O
Open
3.3V
O
O
1
-
2
5V
O
O
3
-
4
12V
Never unplug/replug this while in use
3.5 Panel voltage configuration JP1501
Pin
Description
O
O
Open
3.3V
O
O
1
-
2
5V
O
O
3
-
4
12V
Never unplug/replug this while in use
3.6 Display port power configuration JP500
Pin
Description
O
1
-
2
Board provides power to pin 20 of DP connector
O
Open
Pin 20 DP connector open
Never unplug/replug this while in use

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Configuration
7
3.7 Serial port configuration JP1300
Pin
Description
O
1
-
2
Uart0 is TTL/USB, Uart1 RS232
O
2
-
3
Uart0 and Uart1 are RS232
O
Never unplug/replug this while in use

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Connectors
8
4. Connectors
4.1 SVHS Video Input CN300
Pin
Name
Description
O
1
GND Power Ground
O
2
GND Power Ground
O
3
Y Y component of video signal
O
4
C C component of video signal
4.2 Composite video input CN301
Pin
Name
Description
O
1
GND Power Ground
O
2
CVBS CVBS video signal
4.3 YUV analog input CN302 (optional)
Description
Name
Pin
Pin
Name
Description
Red/Y in RED
1
O O
2
GND Ground
Green/U in GREEN
3
O O
4
GND Ground
Blue/V BLUE
5
O O
6
GND Ground
Audio Left 1 in AIL1
7
O O
8
GND Ground
Audio Right 1 in AIR1
9
O O
10
GND Ground
4.4 VGA/RGB analog Input CN303 (optional)
Pin
Name
Description
O
1
RED Analog input red
O
2
GND Ground
O
3
GREEN Analog input green
O
4
GND Ground
O
5
BLUE Analog input blue
O
6
GND Ground
O
7
DDC_SDA DDC Serial Data
O
8
HSYNC Horizontal Sync input
O
9
VSYNC Vertical Sync input
O
10
DDC_SCL DDC Serial Clock
O
11
GND Ground
O
12
+5V in +5V Power Supply from Video Card

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Connectors
9
4.5 DVI-I input connector CN400
Description
Name
Pin
Pin
Name
Description
Receiver Signal(-) ( RX2- ) RX2-
1
O
O
2
RX2+ Receiver Signal(+) ( RX2+ )
Power Ground GND
3
O
O
4
NC Not connected
Not connected NC
5
O
O
6
SCL I
2
C clock
I
2
C Data SDA
7
O
O
8
NC Not connected
Receiver Signal(-) ( RX1- ) RX1-
9
O
O
10
RX1+ Receiver Signal(+) ( RX1+ )
Power Ground GND
11
O
O
12
NC Not connected
Not connected NC
13
O
O
14
+5V +5V from DVI video card
Power Ground GND
15
O
O
16
HP Hot Plug
Receiver Signal(-) ( RX0- ) RX0-
17
O
O
18
RX0+ Receiver Signal(+) ( RX0+ )
Power Ground GND
19
O
O
20
NC Not connected
Not connected NC
21
O
O
22
GND Power Ground
Clock Signal(+) (RXC+) RXC+
23
O
O
24
RXC- Clock Signal(-) (RXC-)
Analog red RED
C1
O
O
C2
GREEN Analog green
Analog blue BLUE
C3
O
O
C4
HSYNC Horizontal sync
Analog GND GND
C5
O
O
C5
-
1
GND Analog GND
4.6 Display Port connector CN500
Pin
Name
Description
O
1
ML_Lane 0 (p) Lane 0 (positive)
O
2
GND Ground
O
3
ML_Lane 0 (n) Lane 0 (negative)
O
4
ML_Lane 1 (p) LANE 1 (POSITIVE)
O
5
GND Ground
O
6
ML_Lane 1 (n) Lane 1 (negative)
O
7
ML_Lane 2 (p) Lane 2 (positive)
O
8
GND Ground
O
9
ML_LANE 2 (N) LANE 2 (NEGATIVE)
O
10
ML_Lane 3 (p) Lane 3 (positive)
O
11
GND GROUND
O
12
ML_Lane 3 (n) LANE 3 (NEGATIVE)
O
13
GND Pulled to Ground
O
14
GND Pulled to Ground
O
15
AUX CH (p) Auxiliary Channel (positive)
O
16
GND Ground
O
17
AUX CH (n) Auxiliary Channel (negative)
O
18
Hot Plug Hot Plug Detect
O
19
RETURN Return for Power
O
20
DP_PWR POWER FOR CONNECTOR (3.3 V 500 MA)

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Connectors
10
4.7 JILI44-Interface CN600
Description
Name
Pin
Pin
Name
Description
Enables Backlight BLON#
1
O O
2
BLADJ Backlight Adjust
Even Rx Signal(-) (R2IN 4+) STX4+
3
O O
4
STX4- Even Rx Signal(-) (R2IN 4-)
Power Ground GND
5
O O
6
STX3+ Even Rx Signal(-) (R2IN 3+)
Even Rx Signal(-) (R2IN 3-) STX3-
7
O O
8
GND Power Ground
Even Clock Signal(+) (CK2IN +) STXC+
9
O O
10
STXC- Even Clock Signal(-) (CK2IN -)
Power Ground GND
11
O O
12
STX2- Even Rx Signal(-) (R2IN 2-)
Even Rx Signal(+) (R2IN 2+) STX2+
13
O O
14
GND Power Ground
Even Rx Signal(-) (R2IN 1-) STX1-
15
O O
16
STX1+ Even Rx Signal(+)(R2IN1+)
Power Ground GND
17
O O
18
STX0+ Even Rx Signal(+) (R2IN 0+)
Even Rx Signal(-) (R2IN 0-) STX0-
19
O O
20
GND Power Ground
Odd Rx Signal(+)(R1IN 4+) FTX4+
21
O O
22
FTX4- Odd Rx Signal(+)(R1IN 4-)
Power Ground GND
23
O O
24
FTX3+ Odd Rx Signal(+)(R1IN 3+)
Odd Rx Signal(-) (R1IN 3-) FTX3-
25
O O
26
GND Power Ground
Odd Clock Signal(+) (CK1IN +) FTXC+
27
O O
28
FTXC- Odd Clock Signal(-) (CK1IN -)
Power Ground GND
29
O O
30
FTX2+ Odd Rx Signal(-) (R1IN 2+)
Odd Rx Signal(+)(R1IN 2+) FTX2-
31
O O
32
GND Power Ground
Odd Rx Signal(+) (R1IN 1+) FTX1+
33
O O
34
FTX1- Odd Rx Signal(-) (R1IN 1-)
Power Ground GND
35
O O
36
FTX0+ Odd Rx Signal(+)(R1IN 0+)
Odd Rx Signal(-) (R1IN 0-) FTX0-
37
O O
38
GND Power Ground
I
2
C clock SCL
39
O O
40
SDA I
2
C Data
Panel VCC ( switched ) Vcc_P
41
O O
42
Vcc_P Panel VCC ( switched )
Panel VCC ( switched ) Vcc_P
43
O O
4
4
Vcc_P Panel VCC ( switched )
4.8 JILI40-Interface CN601
Description
Name
Pin
Pin
Name
Description
Enables Backlight BLON#
1
O O
2
BLON# Enables Backlight
Backlight Adjust BLADJ
3
O O
4
STX3+ Even Rx Signal(+) (R2IN 3+)
Even Rx Signal(-) (R2IN 3-) STX3-
5
O O
6
+12V +12V
Even Clock Signal(+) (CK2IN +) STXC+
7
O O
8
STXC- Even Clock Signal(-) (CK2IN -)
+12V +12V
9
O O
10
STX2+ Even Rx Signal(+) (R2IN 2+)
Even Rx Signal(-) (R2IN 2-) STX2-
11
O O
12
+12V +12V
Even Rx Signal(+)(R2IN1+) STX1+
13
O O
14
STX1- Even Rx Signal(-) (R2IN 1-)
+12V +12V
15
O O
16
STX0+ Even Rx Signal(+) (R2IN 0+)
Even Rx Signal(-) (R2IN 0-) STX0-
17
O O
18
+12V +12V
Odd Rx Signal(+)(R1IN 3+) FTX3+
19
O O
20
FTX3- Odd Rx Signal(-) (R1IN 3-)
Power Ground GND
21
O O
22
GND Power Ground
I
2
C clock SCL
23
O O
24
SDA I
2
C Data
Power Ground GND
25
O O
26
FTXC+ Odd Clock Signal(+) (CK1IN +)
Odd Clock Signal(-) (CK1IN -) FTXC-
27
O O
28
GND Power Ground
Odd Rx Signal(+)(R1IN 2+) FTX2+
29
O O
30
FTX2- Odd Rx Signal(-) (R1IN 2-)
Power Ground GND
31
O O
32
FTX1+ Odd Rx Signal(+) (R1IN 1+)
Odd Rx Signal(-) (R1IN 1-) FTX1-
33
O O
34
GND Power Ground
Odd Rx Signal(+)(R1IN 0+) FTX0+
35
O O
36
FTX0- Odd Rx Signal(-) (R1IN 0-)
Power Ground GND
37
O O
38
GND Power Ground
Panel VCC ( switched ) Vcc_P
39
O O
40
Vcc_P Panel VCC ( switched )

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Connectors
11
4.9 JILI30-Interface CN603
Description
Name
Pin
Pin
Name
Description
Odd Rx Signal- (R1IN 0-) FTX0- 1 O O 2 FTX0+ Odd Rx Signal+ (R1IN 0+)
Odd Rx Signal- (R1IN 1-) FTX1- 3 O O 4 FTX1+ Odd Rx Signal+ (R1IN 1+)
Odd Rx Signal- (R1IN 2-) FTX2- 5 O O 6 FTX2+ Odd Rx Signal+ (R1IN 2+)
Power Ground GND 7 O O 8 FTXC- Odd Clock Signal- (CK1IN -)
Odd Clock Signal+ (CK1IN +) FTXC+ 9 O O 10 FTX3- Odd Rx Signal- (R1IN 3-)
Odd Rx Signal+ (R1IN 3+) FTX3+ 11 O O 12 STX0- Even Rx Signal- (R2IN 0-)
Even Rx Signal+ (R2IN 0+) STX0+ 13 O O 14 GND Power Ground
Even Rx Signal- (R2IN 1-) STX1- 15 O O 16 STX1+ Even Rx Signal+ (R2IN 1+)
Power Ground GND 17 O O 18 STX2- Even Rx Signal- (R2IN 2-)
Even Rx Signal+ (R2IN 2+) STX2+ 19 O O 20 STXC- Even Clock Signal- (CK2IN -)
Even Clock Signal+ (CK2IN +) STXC+ 21 O O 22 STX3- Even Rx Signal- (R2IN 3-)
Even Rx Signal+ (R2IN 3+) STX3+ 23 O O 24 GND Power Ground
I²C Data SDA 25 O O 26 DEN Display Enable
I²C Clock SCL 27 O O 28 Vcc_P Panel VCC ( switched )
Panel VCC ( switched ) Vcc_P 29 O O 30 Vcc_P Panel VCC ( switched )

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Connectors
12
4.10 Backlight Connector CN7001
Pin
Name
Description
O
1
BLON BACKLIGHT CONTROL SIGNAL
O
2
GND Power Ground
O
3
GND Power Ground
O
4
Backlight power supply TYPICAL. +12V (NOTE SAME AS DC INPUT
VOLTAGE , 1 AMPERE PER CONTACT
ALLOWED)
O
5
Backlight power supply
O
6
Backlight power supply
O
7
Backlight power supply
O
8
GND Power Ground
O
9
GND Power Ground
O
10
BKLTADJ analog 0V to +5V or 0V to +12V
4.11 Audio input/output CN700 (optional)
Description
Name
Pin
Pin
Name
Description
Line out left AOL
1
O O
2
GND Ground
Line out right AOR
3
O O
4
GND Ground
Line in left 2 AIL2
5
O O
6
GND Ground
Line in right 2 AIR2
7
O O
8
GND Ground
SPDIF in SPDIFI
9
O O
10
GND Ground
SPDIF out SPDIFO
11
O O
12
+3.3V +3.3V power supply
4.12 IR input CN800
Pin
Name
Description
CN1001
O
1
VCC 5 Volts output
O
2
GND Power Ground
O
2
Out Output from the IR receiver
4.13 OSD keypad connector CN801
Description
Name
Pin
Pin
Name
Description
+5V DC Power VCC
1
O O
2
LED LED Enable (Operating)
Confirm Key (TTL) KEY
3
O O
4
KEY OSD Menu key (TTL)
Down Key (TTL) KEY
5
O O
6
KEY Up Key (TTL)
ADC Input *Note1 ADC1
7
O O
8
IR Output of IR receiver
Switch LED (TTL) KEY
9
O O
10
KEY ON/OFF Key (TTL)
Low active Reset (TTL) /Reset
11
O O
12
+12V +12V DC Power
Power Ground GND
13
O O
14
GND +5V DC from DVI video card
*Note1: Input range is 0 - 3V. Shared with CN900

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Connectors
13
4.14 ADC Input Connector CN900 (Light Sensor Input)
Connector: Molex 53261-0590
Matching Connector: Molex 51021-0500
Pin
Name
Description
O
1
GND Power Ground
O
2
ADC1 ADC1 Input *Note1
O
3
DVDD3.3
3.3 VOLT OUTPUT SOUR
CE (MAX.50MA)
O
4
ADC2 ADC2 Input *Note1
O
5
GND Power Ground
*Note1: Input range is 0 - 3V. Onboard pulled up to DVDD3.3 through 4, 7 KΩresistor.
4.15 GPIO Connector CN 801
Connector: Molex 53261-0590
Matching Connector: Molex 51021-0500
Pin
Name
Description
O
1
DVD3.3 3.3 Volt output source (max.50mA)
O
2
GND Ground
O
3
GPIO0 General Purpose I/O / PWM0
O
4
GPIO1 General Purpose I/O / PWM1
O
5
GPIO2 General Purpose I/O / PWM2
4.16 RS232 Serial OSD connector CN1300
Description
Name
Pin
Pin
Name
Description
Not Connected NC
1
O O
2
NC Not Connected
Transmit Signal 1 TXD1
3
O O
4
RXD2 Receive Signal 2
Receive Signal 1 RXD1
5
O O
6
TXD2 Transmit Signal 2
Not Connected NC
7
O O
8
NC Not Connected
Power Ground GND
9
O O
10
+5V +5V DC Power
4.17 USB Serial OSD connector (optional)
Connector: Molex 53261-0590
Matching Connector: Molex 51021-0500
Pin
Name
Description
O
1
+5V USB 5V input
O
2
GND USB+
O
3
GPIO0 USB-
O
4
GPIO2 GND

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Connectors
14
4.18 DC Power Supply 4-Pol. CN1500
Pin
Name
Description
O
1
NC Not connected
O
2
GND Power Groundl
O
3
GND Power Ground
O
4
+12V 12V DC Power
4.19 DC Power Supply DC-Jack CN1501
Pin
Name
Description
O
1
+12V +12 V DC
O
2
GND Power Ground

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
On Screen Display
15
5. On Screen Display
With the OSD ( On Screen Display ) you can modify the settings and control the special
features of the CRTtoLCD-71. The OSD uses a number of menus for making changes and
turning the special features on or off. The configuration can be done via the OSD-keypad
(OSD-Panel-Kit).
To start the OSD press the “OSD” button on the keypad, after switching the power supply
on. If a valid flat panel configuration is installed, the OSD Main Menu will be displayed.
To select an menu point, simply use the button “UP” or ”DOWN” to move the cursor to the
menu point you want and press the button “OSD”. To get back to the previous menu point
press the “CONFIRM” button.
To select a function, simply use “OSD”-button to select the field.
Use “UP” or “DOWN” to select a value for that field. With the “CONFIRM” button you can exit
the current function.

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Technical Specifications
16
6. Technical Specifications
These values were measured with OSD-Panel attached and without flatpanel and
backlight inverter.
- Supply voltage at 25˚C :
Minimum supply voltage + 11,4 V DC / 22,8 V DC
Typical supply voltage + 12,0 V DC / 24V DC
Absolute Maximum supply voltage + 12.6 V DC / 25.2 V DC
- Typical Input current at 25˚C:
CRTtoLCD-71- OSD-keypad, input signal SXGA: TBD mA
CRTtoLCD-71- OSD-keypad, power down: TBD mA
- Supply voltage ripple: 100 mV peak to peak 0 – 20 MHz
VGA connector signals :
Sync input voltage low : 0.8 V
Sync input voltage high: 2.4 V
RGB input voltage: 0 – 0.7 V with 75 Ohm external
termination
RGB input current: 0 – 5 mA
- Current Rating of Flatpanel Power supply (preliminary):
PANEL VCC Steady State 3V / 5V and 12V @ +-5% : 3A
PANEL VCC 5sec. -5% 3V3 @5,6A
PANEL VCC 5sec. -5% 5V @ 5,15A
PANEL VCC 5sec. -2% 12V @ 4A
Note: Output power without any switch or short circuit breaker
- Temperature:
ambient: 0˚C – 60˚C (*1)
non operating: -10˚C – 85˚C
(*1) The maximum operating temperature is the maximum measurable temperature on any
spot on the module surface. It is the user responsibility to keep this temperature within the
above specification.
- Temperature gradient:
operating: 25˚C per hour
non operating: 40˚C per hour
- Relative Humidity:
operating: 10% - 90% RH non-condensing
non operating: 5% - 95% RH non-condensing
- Mechanical:
Shock: 5G/20ms square wave maximum
Vibration: 1G/0-600Hz, dwell not to exceed

eCOUNT Technology GmbH
Schatzbogen 60
D-81829 München
Tel.: [phone]
Fax.: [phone]
Technical Specifications
17
- Dimensions of the printed circuit board:
Width: 114.29 mm
Length: 179.07 mm
Thickness: 1.50 mm
- Dimensions of the module:
Width: 119.50 mm
Length: 179.07 mm
Height: 16.50 mm max. 35mm
Note : The dimension of the module may vary depending on P/N or change if cable, Adapter
or Keypad plugged in!