Edelbrock 5708 User manual

©2006 Edelbrock Corporation
Catalog #5708
Brochure No. 63-5708
Rev. 10/06 - DA/mc
Page 1 of 2
EDELBROCK CAT-BACK EXHAUST SYSTEM
For 2000-2006 Toyota Tundra 3.7L & 4.7L V8, 2WD & 4WD
Catalog #5708
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new Edelbrock Cat-Back Exhaust System. If you have any
questions, please contact our Technical Hotline at: 1-800-416-8628 , 7am - 5pm, Monday-Friday, Pacific Standard
Time or e-mail us at [email protected].
Suggested Tools for Installation:
❑3/8" ratchet set and metric sockets ❑9/16” and 15mm wrench ❑Hacksaw
❑Jack and jackstands ❑Liquid penetrant and rubber lubricant
NOTE BEFORE YOU START:
This Edelbrock cat-back system comes with three different I-pipes. This is because some Tundras (between 2000-2006)
use three catalytic converters. Others use 2 catalytic converters and a resonator. If your vehicle came from the factory
with 3 catalytic converters, you will use I-pipe #25-3269 behind the third catalytic converter. If your vehicle came from
the factory with 2 catalytic converters and a resonator, you have the choice of either retaining the resonator for a more
melow exhaust tone, or eliminating the resonator which will give you a more aggressive exhaust tone. See appropriate
steps below.
DISASSEMBLY
Vehicles Equipped with 3 O.E. Catalytic Converters:
1. Remove the V-band clamp behind the rear most
catalytic converter.
2. Remove the stock hanger bars from their isolators
behind the third catalytic converter and remove the
O.E. exhaust system from the vehicle.
3. Install I-pipe #25-3269 behind the rear most
catalytic converter
(See Fig. 1).
Vehicles Equipped with 2 O.E. Catalytic Converters
& A Resonator:
1. If you are retaining your O.E., resonator, cut the
factory I-pipe 10” from the back of the O.E.
resonator. If you want to eliminate the O.E.
resonator, cut the factory I-pipe right where it enters
the O.E. resonator.
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may
result in poor performance and engine or vehicle damage.
INSTALLATION INSTRUCTIONS
IMPORTANT NOTES:
•Support your vehicle with proper jackstands or ramps rated for the total vehicle weight. Place stands so that the rear
axle is allowed to hang free for easy system removal.
•These cat-back systems are engineered to fit stock catalytic converters or equivalent replacements. If you original
system has been modified, Edelbrock will not warranty fit or performance.
Fig. 1
2. Remove the stock hanger bars from their isolators
behind the resonator and remove the O.E. exhaust
system from the vehicle.

©2006 Edelbrock Corporation
Catalog #5708
Brochure No. 63-5708
Rev. 10/06 - DA/mc
Page 2 of 2
Edelbrock Corporation, 2700 California St., Torrance, CA 90503
Tech Line: [phone]
E-Mail: [email protected]
KIT CONTENTS
WARNING!!!
Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before driving!
ASSEMBLY
1. If using original resonator, use 2-1/2” band clamp on
end of I-pipe, #25-3248 and install over cut end of
resonator pipe, slip hanger into rubber isolator. I-
pipe #25-3248 must slide into resonator pipe a
minimum of 2”.
If not using original resonator, use 2-1/2” band
clamp on end of I-pipe #25-3247 and install over cut
end of Y-pipe. I-pipe #25-3247 must slide onto Y-
pipe a minimum of 2”. Cut I-pipe #25-3248 on
reduced end back 3-3/8” so to remove reduced end,
and deburr. Place 3” band clamp on front I-pipe.
Install rear I-pipe #25-3248 into front I-pipe, engage
hanger in rubber isolator.
NOTE: Snug clamps only so system can be adjusted
during installation.
Qty. Part # Desription
❑1 23-4081 Hanger Clamp Assy.
❑1 23-4082 Hanger Clamp Assy.
❑1 25-3247 I-Pipe Front
❑1 25-3248 I-Pipe Rear
❑1 25-3269 I-Pipe (3 catalytic converters)
Qty. Part # Desription
❑1 25-3249 Overaxle Pipe
❑1 25-3223 Tailpipe
❑1 25-55725 Muffler
❑3 46-6612 Band Clamps; 3”
❑2 46-6610 Band Clamps; 2-1/2”
2. Slip the muffler onto the intermediate pipe with a 3”
band clamp on the front. NOTE: Inlet end of muffler
is marked. Snug the clamp so you can adjust the
system later.
3. Install muffler hanger assembly #23-4081 into
muffler rubber isolators from the front of isolators
and slip over muffer outlet.
4. Install overaxle pipe into outlet of muffler.
5. Install overaxle hanger assembly #23-4082 by
slipping over outlet end of overaxle pipe and engage
hanger in rubber isolator.
6. Slip tailpipe onto overaxle pipe, install 3” band clamp
and snug clamp.
7. Align system for clearance to body, frame, and
driveline as you tighten the system from front to rear.
Hanger clamps can be used to properly align system.
8. Check for leaks and correct, if necessary.