manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Edelbrock
  6. •
  7. Automobile Part
  8. •
  9. Edelbrock 5735 User manual

Edelbrock 5735 User manual

©2006 Edelbrock Corporation
Catalog #5735
Page 1 of 2 Brochure #63-5735
Rev. 9/06 - KS/mc
EDELBROCK CAT-BACK EXHAUST SYSTEM
For 2004-2005 Dodge Ram, Standard & Quad Cab,
5.7L Hemi V8, 2 & 4 WD
Catalog #5735
INSTALLATION INSTRUCTION
Please study these instructions carefully before installing your new Cat-Back Exhaust System. If you have any questions,
contact our Technical Hotline at: 1-800-416-8628 from 7 am - 5 pm, Monday through Friday, Pacific Standard Time
or e-mail us at [email protected].
SUGGESTED TOOLS FOR INSTALLATION:
❑3/8" ratchet set with SAE and metric sockets ❑9/16” and 15mm wrenches
❑Jackstands and jack ❑Liquid penetrant and rubber lubricant
DISASSEMBLY
1. Raise vehicle and support with proper
jackstands for the weight, leaving the
suspension hanging.
2. Use caution around hot exhaust systems to
avoid burns.
3. Use penetrating oil on all nuts and bolts.
4. Remove the bolts and clamps from the system
and lubricate the rubber hangers to ease
removal.
5. Use a long pry bar to pull the rubber hangers off
of the pipe hangers.
6. Remove the old system. In some cases, you will
find it easier to cut the overaxle pipe to remove
it.
Note: On some vehicles, the removal of the
straight pipe behind the cat-converter will not
be necessary. This can be determined by laying
the cat-back system out next to or under your
truck to compare length.
ASSEMBLY
1. Install the intermediate pipe (#25-3237) to the
catalytic converter with a 2-3/4” band clamp
and just snug the clamp at this time. I-pipe
should be installed so it raises the exhaust
WARNING: Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before
driving!
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may
result in poor performance and engine or vehicle damage.
system. Slide wire hanger assembly (#23-4074)
onto intermediate pipe and engage wire into
original front rubber isolator. Leave clamp loose
at this time.
2. Slip the muffler onto the intermediate pipe with a
3” band clamp on the front. Inlet of muffler is
stamped in the nipple.
3. Install hanger clamp assembly (#23-4075) onto
outlet end of muffler. Clamp will be offset toward
rear of vehicle, engage hangers into the stock
rubber isolators as you slip it onto the muffler
outlet. U-clamp will be kicked forward on the
hanger clamp assembly. Slip the overaxle pipe
over the rear end and into the muffler outlet,
engage hanger at rear into stock rubber isolator.
4. Put one 3” band clamp onto outlet of overaxle
pipe, install tailpipe and snug band clamp.
5. Working from the front of the system, align and
tighten each pipe from the cat-back.
NOTE: The I-pipe can be used to adjust the
exhaust system right, left, up, or down. This can
be done by simply twisting the I-pipe.
6. Check for clearance to body, frame, and driveline
as you tighten the system from front to rear.
7. Check for leaks and correct, if any is found.
INSTALLATION INSTRUCTIONS
©2006 Edelbrock Corporation
Catalog #5735
Page 2 of 2 Brochure #63-5735
Rev. 9/06 - KS/mc
KIT CONTENTS
CATALOG #5735
WARNING: Support your vehicle with proper
jackstands or ramps rated for the total
vehicle weight. Place stands so that the rear
axle is allowed to hang free for easy system
removal.
WARNING: These cat-back systems are
engineered to fit vehicles with stock catalytic
converters or equivalent replacements. If
your original system has been modified,
Edelbrock will not warranty fit or
performance.
Overaxle / Tail Pipe Assembly
Intermediate Pipe Assembly
Hanger Clamp Assembly
SDT Series Muffler #55754
Qty Part # Description
❑125-3237 Intermediate Pipe
❑1 25-55725 Muffler
❑123-3238 Overaxle Pipe Assembly
❑125-3157 Tail Pipe
Band Clamp
Band Clamp
Edelbrock Corporation, 2700 California Street, Torrance, CA 90503
Tech Line: 1-800-416-8628
E-mail: [email protected]
Qty Part # Description
❑2 46-6612 3” Band Clamps
❑1 23-4075 Hanger Clamp Assembly
❑1 23-4074 I-pipe Hanger Assembly
❑1 46-6611 2-3/4” Band Clamp
Hanger Clamp
Assembly

This manual suits for next models

1

Other Edelbrock Automobile Part manuals

Edelbrock 70402 User manual

Edelbrock

Edelbrock 70402 User manual

Edelbrock 6009 User manual

Edelbrock

Edelbrock 6009 User manual

Edelbrock 351-M/400 User manual

Edelbrock

Edelbrock 351-M/400 User manual

Edelbrock 2263 User manual

Edelbrock

Edelbrock 2263 User manual

Edelbrock 68812 User manual

Edelbrock

Edelbrock 68812 User manual

Edelbrock 7501 User manual

Edelbrock

Edelbrock 7501 User manual

Edelbrock 71920 User manual

Edelbrock

Edelbrock 71920 User manual

Edelbrock 5682 User manual

Edelbrock

Edelbrock 5682 User manual

Edelbrock 7129 User manual

Edelbrock

Edelbrock 7129 User manual

Edelbrock Performer RPM 1967 User manual

Edelbrock

Edelbrock Performer RPM 1967 User manual

Edelbrock 70207 User manual

Edelbrock

Edelbrock 70207 User manual

Edelbrock CHEVROLET V8 302-400 C.I.D. User manual

Edelbrock

Edelbrock CHEVROLET V8 302-400 C.I.D. User manual

Edelbrock Russell R09392S User manual

Edelbrock

Edelbrock Russell R09392S User manual

Edelbrock 6700 User manual

Edelbrock

Edelbrock 6700 User manual

Edelbrock 65272 User manual

Edelbrock

Edelbrock 65272 User manual

Edelbrock 2186 User manual

Edelbrock

Edelbrock 2186 User manual

Edelbrock 72000 User manual

Edelbrock

Edelbrock 72000 User manual

Edelbrock 71836 User manual

Edelbrock

Edelbrock 71836 User manual

Edelbrock 70405 User manual

Edelbrock

Edelbrock 70405 User manual

Edelbrock 7788 User manual

Edelbrock

Edelbrock 7788 User manual

Edelbrock 5652 User manual

Edelbrock

Edelbrock 5652 User manual

Edelbrock Russell 641550 User manual

Edelbrock

Edelbrock Russell 641550 User manual

Edelbrock 66182 User manual

Edelbrock

Edelbrock 66182 User manual

Edelbrock Intake Manifolds Application guide

Edelbrock

Edelbrock Intake Manifolds Application guide

Popular Automobile Part manuals by other brands

BBK 18950 installation instructions

BBK

BBK 18950 installation instructions

Rostra 250-4235 user manual

Rostra

Rostra 250-4235 user manual

Rugged Ridge 11252.51 installation instructions

Rugged Ridge

Rugged Ridge 11252.51 installation instructions

Demco TP20047 Assembly operation replacement parts

Demco

Demco TP20047 Assembly operation replacement parts

SAF-HOLLAND B9 Maintenance Instruction

SAF-HOLLAND

SAF-HOLLAND B9 Maintenance Instruction

ICI FBM06DGN Installation

ICI

ICI FBM06DGN Installation

Energy Suspension Bicycle installation instructions

Energy Suspension

Energy Suspension Bicycle installation instructions

Airdog II DF-100 installation manual

Airdog

Airdog II DF-100 installation manual

Vintage 1967-72 CHEV PICK-UP instructions

Vintage

Vintage 1967-72 CHEV PICK-UP instructions

Webasto Thermo 90 ST installation manual

Webasto

Webasto Thermo 90 ST installation manual

banks six-gun owner's manual

banks

banks six-gun owner's manual

BENDIX AH-1B AIR HYD INTENSIFIER manual

BENDIX

BENDIX AH-1B AIR HYD INTENSIFIER manual

Porsche 911 GT3 RS owner's manual

Porsche

Porsche 911 GT3 RS owner's manual

Axxess OESWC-CLASS2-RF installation instructions

Axxess

Axxess OESWC-CLASS2-RF installation instructions

AutoMeter 9117 installation instructions

AutoMeter

AutoMeter 9117 installation instructions

Axxess OESWC-LAN11-RF installation instructions

Axxess

Axxess OESWC-LAN11-RF installation instructions

Whelen Engineering Company Howler installation guide

Whelen Engineering Company

Whelen Engineering Company Howler installation guide

SAF-HOLLAND B9 Maintenance Instruction

SAF-HOLLAND

SAF-HOLLAND B9 Maintenance Instruction

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.