Edelbrock Performer RPM 60219 User manual

Catalog # 60219 - #60399
Rev. 3/09 - AJ/mc
Page 1 of 3 ©2009 Edelbrock Corporation
Brochure #63-0009
Performer and Performer RPM Aluminum Cylinder Heads
For Small Block Ford V8s
Catalog #s 60219, 60229, 60249, 60259, 60269, 60279, 60289, 60299,
60319, 60329, 60349, 60359, 60369, 60379, 60389, 60399, 602479, 602579
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new cylinder heads. If you have any questions, please call our Technical Hotline at:
1-800-416-8628, 7:00 am - 5:00 pm, Monday through Friday, Pacific Standard Time.
DESCRIPTION: The Edelbrock Performer, Performer RPM, and Performer 5.0/5.8L Street Cylinder Heads are designed for street high performance use,
and are interchangeable with original equipment small-block Ford cylinder heads. Performer Ford and Performer 5.0/5.8L heads have exhaust
crossover and air injection passages and are street legal in all 50 states. Contact Edelbrock for the current E.O. number if required for emission
validation. Edelbrock cylinder heads offer "out-of-the-box" bolt-on performance with no additional porting required. The performance range is 1500-
6500 rpm for great throttle response as well as top-end horsepower. The intake and exhaust ports are CNC machine "matched" and have been
designed for maximum flow velocity when matched with either the Performer or the Performer RPM intake manifold, Performer-Plus or Performer RPM
cam kit, and Performer Series Carburetors. The Performer RPM Power Package produced 400 horsepower in dyno tests on 351-W engines.These
heads are designed to use 1/2" head bolts. On 289-302 engines with 7/16" head bolts, you must use Edelbrock head bolt bushings
with integral washers #9680 and Edelbrock head bolt kit #8552 or stock 7/16" head bolts.
IDENTIFICATION: These heads are available individually, either bare or assembled, with either 1.90" or 2.02" (1.94” SCCA only) intake valves for the
following applications:
• Performer RPM Ford head #60219 (bare, 1.90") or #60249 (bare, 2.02"); #60229 (complete, 1.90") or #60259 (complete, 2.02") - For non-
emission-controlled 289, 302, and 351-W V8s with rocker studs and pushrod guideplates (Will not accept rail rockers).
• Performer Ford head #60319 (bare, 1.90") or #60349 (bare, 2.02"); #60329 (complete, 1.90") or #60359 (complete, 2.02") - For emission-
controlled 1965 & later 289, 302, and 351-W with rocker studs and pushrod guideplates (Will not accept rail rockers).
• Performer 5.0/5.8L Ford head #60369 (bare, 1.90") or #60389 (bare, 2.02"); #60379 (complete, 1.90") or #60399 (complete, 2.02") - For
emission-controlled 1982 & later 5.0/5.8L V8s with pedestal mount rocker arms (Will not accept rail rockers).
• Performer RPM SCCA American Sedan Series head #602479 (bare) or #602579 (complete) - For SCCA sanctioned engines.
IMPORTANT NOTE: Refer to SCCA rules specifications before performing any modifications to intake, exhaust or bowl areas.
Complete cylinder heads are assembled with the following components: Stainless steel, one-piece, swirl-polished intake and exhaust valves with
under-cut stems for increased flow; 2-ring positive oil controls seals; 3/8" rocker studs and 5/16" guideplates; Edelbrock Sure-Seat Valve Spring
#5767, retainers #9724, valve keepers #9611. Complete cylinder heads are assembled with hardened valve spring seats and prepared for
installation right out of the box. Bare cylinder heads will have valve guides and seats installed, but will require final sizing and a valve
job to match the valves you will be using.
ACCESSORIES: Although Edelbrock Street Cylinder Heads will accept OEM components (rocker arms, valve covers, intake manifold, head bolts [351-
W only], etc., we highly recommend that premium quality hardware be used with your new heads. See our catalog for details. To order a catalog,
call (800) FUN-TEAM.
Head Bolts or Studs: High quality head bolts or head studs with hardened washers must be used to prevent galling of the aluminum bolt bosses.
Recommended head bolts are ARP #254-3708 for engines with 7/16" head bolt holes (289 and 302). You may use Edelbrock Head Bolt Kit #8552
or stock 7/16" bolts on 289-302 engines only if you purchase Edelbrock head bolt bushings with integral washers #9680. Engines with ½"
diameter head bolts (351-W and 302 SVO) use Edelbrock Head Bolt Kit #8553 or stock 351-W bolts with high quality head bolt washers such as
ARP #200-8533. NOTE: It is recommended that 289-302 engines producing 380 or more horsepower (or with nitrous oxide) be converted to
accept ½" diameter head bolts by a qualified machine shop to ensure maximum head gasket durability.
Rocker Arms: The valve springs supplied will accommodate valve lifts up to .575", which is much higher than stock rocker arms will allow.
Roller rocker arms will be required if your camshaft has more than .480" lift. Stock rockers may require longer-than-stock pushrods to clear the
valve springs.
Valve Covers: Because most roller rockers are physically larger than stock rockers, taller valve covers are usually required to clear them. For
heads #60259, and #60359, use Edelbrock Signature Series chrome valve covers #4260, or cast aluminum Classic valve covers #4160. Performer
5.0/5.8L heads #60379 and #60399 accept stock 5.0/5.8L valve covers, which are required for component clearance on most street applications.
Intake Manifold: Although stock intake manifolds will fit, the Edelbrock Street Cylinder Heads are matched in size and operating range with
Edelbrock Performer or Performer RPM intake manifolds. If the Performer or Performer RPM is too tall to fit under your hood, you may use the
EdelbrockTorker II manifold (#5021 or #5081). Additionally, any manifold that matches Edelbrock gasket #7220, or Fel-Pro gasket #1250 may be
used (Edelbrock Performer, Torker II, Victor Jr., etc.)
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in poor performance
and engine or vehicle damage.

Catalog # 60219 - #60399
Rev. 3/09 - AJ/mc
Page 2 of 3 ©2009 Edelbrock Corporation
Brochure #63-0009
Exhaust Headers: Any header or manifold designed for original equipment heads will fit the Edelbrock Street Cylinder Heads. Exhaust ports are
CNC-profiled to match Edelbrock #7227 or Fel-Pro #1415 exhaust gaskets, which are recommended for this application. For maximum
performance, the opening of exhaust header flange should match an Edelbrock #7227 or Fel-Pro #1415 gasket.
Spark Plugs: Use 14mm x 3/4" reach gasketed spark plugs. Heat range will vary by application from Champion RC9YC to Champion RC14YC.
The RC12YC is the plug used in the RPM applications (or equivalent). Use anti-seize on the plug threads to prevent galling in the cylinder
head, and torque to manufacturer's specification for aluminum heads.
Head Gaskets: Head gaskets requirements change according to the application for which the
cylinder heads are being used. Use the following as a guide for head gasket selection. NOTE: Certain
Ford SVO Performance blocks include additional blind cooling provisions on the exhaust side of the
deck surface. These holes may line up with a tooling point on the deck surface of the cylinder head
(identifiable as a rough low spot), which could prevent the head gasket from sealing properly. Using
the gasket as a template, verify that the head will compress the gasket above any such hole before
drilling. Use a small set-screw to block this passage if necessary, on blocks in which the hole has
already been drilled. NOTE: When using Fel-Pro Print-O-Seal, or any silicone beaded gasket, you
must apply a small strip of silicone to both the deck flange of the cylinder head, as shown to the right,
and the same location on the surface of the block to prevent coolant from contaminating the oil.
1. Engines with low or stock compression ratios (8-10:1), stock size head bolts (7/16"), and applications where the cylinder head is being used
as a stock replacement or a performance upgrade with the stock piston volume, without nitrous or forced induction (blowers or turbos) - use
Edelbrock head gasket #7313 or Fel-Pro Head Gasket, #9333-PT1.
2. Medium performance engines, 10-12:1 compression ratio, increased pre-load cylinder head fasteners (7/16" stud or ½" head bolts or studs),
not recommended with nitrous or forced induction - Edelbrock head gasket #7313 or Fel-Pro Head Gasket, #1011-2.
3. Highest performance racing engines. 12:1 and above compression ratio, ½" cylinder head fasteners designed for the highest pre-load,
engines using nitrous or forced induction - Fel-Pro Head Gasket #1006 Locwire. NOTE: This gasket will require a groove to be cut in the
deck surface of the cylinder head by a competent machine shop to Fel-Pro specifications. See “OTHER ASSEMBLY TIPS:” below.
NOTE: For applications 1 & 2 above, Edelbrock Cylinder Head Gasket Set #7364 may also be used. This gasket set includes all gaskets necessary
for installation of Edelbrock cylinder heads, including cylinder head, intake manifold, exhaust, and valve cover gaskets.
INSTALLATION: Before final installation of the cylinder heads, several things need to be checked to assure proper engine operation:
1. Check the upper deck to see if you have an early or late model block (not needed with 351-W): a) Late model 289-302 blocks have the water
passages located next to the head bolt location on the deck of the block (This block will not require drilling). b) Early 289-302 blocks will
have the water passages located directly over the cylinder upper deck area and will require drilling 1/8" steam holes as seen in Figure 2.
2. Piston to Valve Clearance - Minimum intake valve clearance should be .080". Minimum exhaust valve clearance should be .110". The
point of minimum intake valve to piston clearance will usually occur somewhere between 5° and 20° ATDC during valve overlap. The point
of minimum exhaust valve to piston clearance will usually occur 20° to 5° BTDC during valve overlap. With #60259, #602579, #60359
and #60399 heads, re-machining of the piston top eyebrows may be required with some pistons. Heads with 1.90" intake valves
(#60229, 60329, & 60379) should be compatible with stock pistons in engines that have the stock or recommended camshafts.
3. Proper Hydraulic Lifter Pre-Load and Rocker Geometry - With #60229, #60259, #60329 and #60359 cylinder heads, hydraulic lifter
pre-load is easily adjustable due to the stud/guideplate design. On #60379 and #60399 Performer 5.0/5.8L heads, adjustments to
lifter pre-load with non-adjustable pedestal bolt-down style rockers can only be made with shims as sold by Ford SVO #M-
6529-A302 or Crane #99170-1. Rocker geometry should be checked making sure that the contact point of the roller or pad on a stock
rocker remains properly on the valve tip and does not roll off the edge. Visual inspection of the rockers, valve springs, retainers, and pushrods
should be made to ensure that none of these components come into improper contact with each other. If problems with valve train geometry
occur, simple changes such as pushrod length may have to be made.
OTHER ASSEMBLY TIPS:
• When installing the sparkplugs and exhaust manifolds, be sure to use a high temperature anti-seize compound on the threads to reduce the
possibility of thread damage in the future.
•Do not exceed a torque of 16-18 ft./lbs. on the intake manifold bolts and lubricate the bolt threads prior to assembly.
• For emissions passage equipped cylinder heads (#60329, #60359, #60379, & #60399), plugs have been supplied for the air injection
passage, which is drilled in the end of the heads. The plugs should be installed in the front of the heads to seal off the passages, and the
stock air injection manifold is installed on the back of the engine in the stock location.
• If pushrod to cylinder head contact is a problem, loosen rocker studs and re-position guideplate as needed for clearance.
• Installation is the same as for original equipment cylinder heads. Consult service manual for specific procedures, if necessary. Head gasket
recommendations are listed in the head gasket section. Be sure that the surface of the block and the surface of the head are thoroughly
cleaned to remove any oily film before installation. Use alcohol or lacquer thinner on a lint-free rag to clean. Apply moly-oil mixture to head
bolt threads, washer, and area under head bolt to prevent galling and improper torque readings. Torque to 70 ft./lbs. for 7/16" bolts (289/302)
or 100 ft./lbs. for ½" bolts (351-W) in three or four steps following the factory tightening sequence (see Figure 1), then tighten the long (upper)
head bolts to 80 ft./lbs. (7/16") or 110 ft./lbs. (1/2"). A re-torque is recommended after initial start-up and cool-down (allow 2-3 hours for
adequate cooling).

Catalog # 60219 - #60399
Rev. 3/09 - AJ/mc
Page 3 of 3 ©2009 Edelbrock Corporation
Brochure #63-0009
SPECIFICATIONS
Head Bolt Torque: 7/16" bolts - 70/80 ft./lbs. (short/long
bolts)1/2" bolts - 100/110 ft./lbs.
(short/long bolts)
Intake Bolt Torque: 16-18 ft./lbs.
Rocker Studs: 3/8" (#6022, 6025, 6032, 6035)
Rocker Stud Torque: 45 ft./lbs. (7/16"-14; #6022-#6035)
Rocker Pedestal Bolt Torque: 18-20 ft./lbs. (5/16"-18; #6036-39)
Combustion Chamber Volume: 58-60cc
Intake Port Volume: 170cc
Exhaust Port Volume: 60cc
Deck Thickness: 5/8"
Valve Seats: Hardened, interlocking ductile iron,
compatible with unleaded fuels
Valve Size:
#60259, #60359 & #60399: Intake - 2.02", Exhaust - 1.60"
#60229, #60329 & #60379: Intake - 1.90", Exhaust - 1.60"
Valve Locks: 11/32" x 7° (#9611)
Valve Spring Retainers: 7° 4140 steel (#9724)
Valve Spring Diameter: 1.45"
Valve Spring Installed Height: 1.800"
Valve Spring Seat Pressure: 110-120 lbs.
Max. Valve Lift: .575"
Pushrod Guideplates: 5/16" Hardened steel (#6022, #6025,
#6032 & #6035 only)
Rocker Arms: #6022, #6025, #6032, & #6035 accept
stock (except rail style) or aftermarket
roller type#6037, & #6039 accept stock
5.0/5.8L or aftermarket pedestal bolt
down style
Pushrods: #6022, #6025, #6032, #6035 require
5/16" hardened pushrods for use with
guideplates#6037 & #6039 use stock
pushrods
Spark Plugs: 14mm x ¾" reach gasketed seat
Recommended Intake Gasket: Fel-Pro #1250
Recommended Exhaust Gasket: Fel-Pro #1415
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503
Tech Line: 800-416-8628 • Office: 310-781-2222
Figure 2 - Steam Hole Locations for Early 289 & 302 Engine Blocks
Figure 1 - Head Bolt Tightening Sequence
95137
10 6 2 4 8
#5 Cylinder
Front Cylinder
LH Bank
(Driver Side)
#1 Cylinder
Front Cylinder
RH Bank
(Pass. Side)
1/8” Holes Drilled
into the Water Jacket.
Position Hole Location
Using the Head Gasket.
• Edelbrock offers cylinder heads machined to the proper
specifications for use with Fel-Pro Locwire head gaskets only
as shown in the table to the right:
Standard Head # Machined for Locwire Head Gaskets
60259 60269
60359 60279
60379 60289
60399 60299