Edelbrock 5624 User manual

©2006 Edelbrock Corporation
Catalog #5624
Page 1 of 2 Brochure #63-5624
Rev. 7/06 - DA/mc
EDELBROCK CAT-BACK EXHAUST SYSTEM
For 2004-2006 Nissan Titan, Extended / Crew Cab,
Short Bed, 5.6L V8, 2 & 4 WD
Catalog #5624
INSTALLATION INSTRUCTION
Please study these instructions carefully before installing your new Cat-Back Exhaust System. If you have any questions,
contact our Technical Hotline at: 1-800-416-8628 from 7 am - 5 pm, Monday through Friday, Pacific Standard Time
or e-mail us at [email protected].
SUGGESTED TOOLS FOR INSTALLATION:
❑3/8" ratchet set with SAE and metric deep sockets
❑Jackstands and jack
❑Liquid penetrant and rubber lubricant
DISASSEMBLY
1. Raise vehicle and support with proper
jackstands for the weight, leaving the
suspension hanging.
2. Use caution around hot exhaust systems to
avoid burns.
3. Use penetrating oil on all nuts and bolts.
4. Measure 10” from the back of the factory Y-pipe
hanger bracket and cut the factory intermediate
pipe.
5. Remove the bolts and clamps from the system
and lubricate the rubber isolators to ease
removal.
6. Use a long pry bar to pull the rubber hangers out
of the OE insulators.
7. Remove the old system. In some cases, you will
find it easier to cut the overaxle pipe to remove
it.
WARNING: Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before
driving!
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may
result in poor performance and engine or vehicle damage.
ASSEMBLY
1. Clamp the intermediate pipe (#25-3241) to the
factory Y-pipe with a 2-1/2” band clamp and just
snug the clamp at this time.
2. Slip the muffler onto the intermediate pipe with a
3” band clamp on the front. Inlet of muffler is
stamped in the nipple.
3. Install hanger clamp assembly (#23-4078) onto
outlet end of muffler. Clamp will be offset toward
rear of vehicle, engage hanger into the stock
rubber isolator. Slip the overaxle pipe over the
rear end and into the muffler outlet.
4. Slide hanger clamp assembly (#23-4079) onto
outlet of overaxle pipe and engage into factory
isolator.
5. Put one 3” band clamp onto outlet of overaxle
pipe, install tailpipe and snug band clamp.
6. Working from the front of the system, align and
tighten each pipe from the cat-back.
7. Check for clearance to body, frame, and driveline
as you tighten the system from front to rear.
8. Check for leaks and correct, if any are found.
INSTALLATION INSTRUCTIONS

©2006 Edelbrock Corporation
Catalog #5624
Page 2 of 2 Brochure #63-5624
Rev. 7/06 - DA/mc
KIT CONTENTS
CATALOG #5624
WARNING: Support your vehicle with proper
jackstands or ramps rated for the total
vehicle weight. Place stands so that the rear
axle is allowed to hang free for easy system
removal.
WARNING: These cat-back systems are
engineered to fit vehicles with stock catalytic
converters or equivalent replacements. If
your original system has been modified,
Edelbrock will not warranty fit or
performance.
Muffler Assembly
Intermediate Pipe Hanger Clamp Location
Qty Part # Description
❑1 25-3241 Intermediate Pipe
❑1 25-55725 Muffler
❑1 23-3242 Overaxle Pipe Assembly
❑1 25-3223 Tail Pipe
Band Clamp
Band Clamp
Edelbrock Corporation, 2700 California Street, Torrance, CA 90503
Tech Line: 1-800-416-8628
E-mail: [email protected]
Qty Part # Description
❑2 46-6612 3” Band Clamps
❑1 23-4078 Hanger Clamp Assembly
❑1 23-4079 I-pipe Hanger Assembly
❑1 46-6610 2-1/2” Band Clamp
Overaxle Pipe
Tail Pipe