Eden 391/7066 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Eden - 3+2 Sideboard
Assembly Instructions - Please keep for future reference
ALR3157
391/7066
414/4034
Width - 119.5cm
Issue 1 - 21/07/15
Depth - 38.1cm
Height - 83.2cm

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 42kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Drawer Front (DF3047)
(36.9 x 24cm) x 2
Middle Drawer
Base (T317-327)
(31.7 x 32.7cm)
Drawer Base
(T353-327)
(35.3 x 32.7cm) x 2
Middle Drawer
Back (W306-195)
(30.6 x 19.5cm)
Drawer Back (W342-195)
(34.2 x 19.5cm) x 2
Left Drawer
Side (W330-195LH)
(33 x 19.5cm) x 3
Right Drawer
Side (W330-195RH)
(33 x 19.5cm) x 3
Middle Drawer
Front (DF3048)
(36.9 x 24cm)
1 3 42
5 6
7 8
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
80%
9 10 11
Shelf (DF4014)
(55.2 x 34.8cm) x 2
Left Side (DF4322)
(79.7 x 37.8cm)
Right Side (DF4321)
(79.7 x 37.8cm)
Top Divider (DF1241)
(23.7 x 34.9cm) x 2
12
Bottom Divider (DF4015)
(48 x 34.9cm)
Horizontal Divider (DF3045)
(111.9 x 35cm)
Top (DF3043)
(119.5 x 38.1cm)
Base (DF4323)
(111.9 x 37.2cm)
Left Door (DF4324)
(48.3 x 55.5cm)
Right Door (DF4013)
(48.3 x 55.5cm)
Back (X1137-762)
(113.7 x 76.2cm)
13 14
15 16
17 18
19

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
B
D E F
G H I
C
R
K L
Small metal dowel (F893) x 8
Hollow core
locking nut
(F892) x 8
Wooden dowel (F22) x 10
J
N
T
13mm Screw (F63) x 8
Knock-in Peg (F171GY) x 12
9mm Screw (F74) x 6 9mm Screw (F73) x 12
Drawer runner (F1004) x 6
Wedgefix (F639) x 6
Large locking
nut (F900) x 12
A
Metal dowel (F901) x 18
M
QO P
Shelf stud (F110) x 8
Hinge plate
(F523) x 4 Hinge (F522) x 4
Small locking
nut (F3) x 6
19mm Screw (F461) x 10
Handle (F414) x 5
SStrap Screw Washer x 2
Overbalance protector kit (F269) x 1
40mm Screw (F910) x 4
Nail (F51) x 25

1
Assembly Instructions
4
Step 1
A
B
A
C
C
CC
34
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
1
Prepare 2 pairs of
drawer sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
3
4
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
3
4
1
C
C
4
3
A
A
1
3
4
x 2
x 2
x 2
x 2
2
2.5cm
0.7cm

1
Assembly Instructions
5
Step 4
Drawer Back
(W378-195)
(37.8 x 19.5cm) x 3
Left Drawer
Side (W330-195LH)
(33 x 19.5cm) x 3
Right Drawer
Side (W330-195RH)
(33 x 19.5cm) x 3
8
Drawer Front (DF3039)
(40.5 x 24cm) x 3
7 9 10
E
E
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
7
3 4
1
10
3 4
7
5
5
E
4
3
7
4
5
7
3
E
E
Step 6
Step 7
Fit the wedgefixes
Turn the 2 drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
F
F
F
F
x 2
x 2
x 2
x 2
Attach the handles
Attach the handle to
each drawer front
using screws .
G
1
R
G
G
R
Drawer Base
(T353-327)
(35.3 x 32.7cm) x 2
Middle Drawer
Base (T317-327)
(31.7 x 32.7cm)
3 4
1
Middle Drawer
Back (W306-195)
(30.6 x 19.5cm)
Drawer Back
(W342-195)
(34.2 x 19.5cm) x 2

2
2
6
Step 8
A
B
A
C
C
CC
34
Step 9
Prepare the middle
drawer front
Screw 2 metal dowels
into the middle drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
A
2
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 10
C
3
4
Attach the drawer
sides to the middle
drawer front
Push the left drawer side
. and right drawer side
. onto the back of the
middle drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
3
4
2
C
C
4
3
A
A
3
4
Assembly Instructions

2
2
Assembly Instructions
7
Step 11
Drawer Back
(W378-195)
(37.8 x 19.5cm) x 3
Left Drawer
Side (W330-195LH)
(33 x 19.5cm) x 3
Right Drawer
Side (W330-195RH)
(33 x 19.5cm) x 3
8
Drawer Front (DF3039)
(40.5 x 24cm) x 3
7 9 10
E
E
Fit the middle drawer
base
Slide the middle drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the middle drawer front
. .
Step 12
Fit the drawer back
Fit the middle drawer
back between the
drawer sides and .
Make sure that the
middle drawer base
fits into the groove in the
middle drawer back .
Hold the middle drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
8
3 4
2
6
3 4
8
6
6
E
4
3
8
4
6
8
3
E
E
Step 13
Step 14
Fit the wedgefixes
Turn the middle drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
F
F
F
F
Attach the handle
Attach the handle to
the middle drawer front
using screws .
G
2
R
G
G
R
3 4
2

D
D
D
D
8
Step 15
Assembly Instructions
B
B
B
B
Prepare the horizontal
divider
Screw 2 metal dowels
into the horizontal divider
. .
Insert 4 large locking
nuts into the
horizontal divider .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 4 wooden dowels
into the horizontal divider
. .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
15
15
15
A
A
B
15
D
10mm
D
D
B
D
Finished
front edge
B
BB
B
Prepare the bottom
divider
Insert 4 large locking
nuts into the bottom
divider .
Tap 2 wooden dowels
into the bottom divider
. .
11
11
15
B
D
D
Step 16
Finished
front edge
11

Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 17
Step 18
Fit the bottom divider
to the horizontal
divider
Push the bottom divider
. onto the horizontal
divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the bottom divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
15
11
B
B
11
A
B
15
11
L
L L
Prepare the base
Push 4 hollow core
locking nuts into the
base , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Turn the base over
Screw 2 metal dowels
into the base .
L
L
14
L
A
14
Turn the
base over
L
L
L
L
A
A
Finished
front edge
Finished
front edge
14
14