Edge-core Asgvolt64 User manual

– 1 –

Quick Start Guide

E082021-MR-R01

150200002424A

64-Port GPON vOLT

ASGvOLT64

2. Rack mounting kit—2 brackets and 24 screws

3. 2 x Power cord

4. Console cable—RJ-45 to D-Sub

5. Documentation—Quick Start Guide (this document) and Safety

and Regulatory Information

1. 64 x SFP GPON ports

2. 2 x QSFP28 40G/100G ports

8 x SFP28 10G/25G ports

4. System LEDs

5. 1 x SFP Management port

6. 1 x 1PPS

7. 1 x RJ45 Management port

8. 1 x RJ45 Console port

9. 1 x USB port

10. 2 x AC PSUs

11. 4 x Fan trays

110

1610

Package Contents

Overview

SFP GPON Port LEDs: Green (link up and in service), Blue (disable),

Red (fault), Blinking (activity)

QSFP28 Port LEDs: Green (100G), Blue (40G), Orange (4G), Blinking

(activity)

SFP28 Port LEDs: Green (25G), Blue (10G), Orange (1G), Blinking

(activity)

UID LED: Blinking blue

FAN LED: Off (OK), Red (fault)

Air Filter LED: Off (OK), Red (change filter)

PSU LEDs: Green (OK), Red (fault)

Alarm LED: Green (OK), Blue (minor), Red (major)

State LED: Green (OK), Blue (initializing), Red (fault)

1PPS LED: Green (OK)

System LEDs Port LEDs

1 2 3 4 5

*150200002424A_R01*

www.edge-core.com

2. B2F Airflow

Install back-to-front (B2F) airflow

fan trays (blue handles) and PSUs

(blue release latches).

Fan Tray Replacement

1. Loosen the fan tray screw.

2. Remove fan tray from the

chassis.

3. Install replacement fan with

matching airflow direction.

PSU Replacement

1. Remove the power cord.

2. Press the release latch and

remove the PSU.

3. Install replacement PSU with

matching airflow direction.

1. F2B Airflow

Remove front-to-back (F2B)

airflow fan trays (red handles) and

PSUs (red release latches).

FRU Replacement Airflow Reversal

Quick Start Guide

– 2 –

Mount the Device

Ground the Device

Connect Power

1. Connect the RTN return. (red wire).

2. Connect the -36 – -72 VDC (black wire).

3. Connect the Chassis Ground (yellow-green wire).

Verify Device Power

Make Network Connections

Warning:

For a safe and reliable installation, use only the

accessories and screws provided with the device. Use of other

accessories and screws could result in damage to the unit. Any

damages incurred by using unapproved accessories are not

covered by the warranty.

Avertissement:

Pour une installation sûre et fiable, utilisez

uniquement les accessoires et les vis fournies avec l’appareil.

L’utilisation d’autres accessoires et vis pourrait endommager

l’appareil. Les dommages causés par l’utilisation d’accessoires

non approuvés ne sont pas couverts par la garantie.

Caution:

The device includes plug-in power supplies (PSUs)

and fan tray modules that are installed into its chassis. Make

sure all installed modules have a matching airflow direction.

Attention:

Le appareil comprend des modules

d’alimentation et de modules de ventilation installés dans son

châssis. Assurez-vous que tous les modules installés ont une

direction d’air adaptée.

Note:

The device has the Open Network Install Environment

(ONIE) software installer preloaded on the switch, but no switch

software image. Information about compatible switch software

can be found at www.edge-core.com.

Note:

Model name and approval markings are indicated on

the product label located on the bottom of the device.

1. Attach the Brackets

Use the included screws to attach the left and right brackets.

2. Mount the Device

Mount the device in the rack and secure it with rack screws.

Ensure the Rack is Grounded

Ensure the rack on which the device is to be mounted is properly

grounded and in compliance with ETSI ETS 300 253. Verify that there

is a good electrical connection to the grounding point on the rack (no

paint or isolating surface treatment).

Ground the Device

Attach a #14 AWG grounding wire (not included) to the grounding

point on the device rear panel. Then connect the other end of the wire

to rack ground.

Caution:

Use a UL/IEC/EN 60950-1 certified power supply

to connect to a DC converter, and a #14 AWG (for -36 – -72

VDC PSU).

Attention:

Utilisez une alimentation certifiée UL/IEC/EN

60950-1 pour le connecter à un convertisseur CC et un câble

AWG #14 (pour -36 – -72 VDC) pour vous connecter à une

alimentation CC.

Note:

DC terminal screws should be tightened to a torque of

6.6 in-lbs.

AC or DC Power

Connect the two AC or DC PSUs to a power source.

Check the PSU LEDs

The PSU1/PSU2 LEDs should be on green when operating normally.

1. SFP GPON slots

First install GPON transceivers and then connect fiber optic cabling to

the transceiver ports.

Installation

Quick Start Guide

– 3 –

Connect the Timing Port

Make Management Connections

2. QSFP28 slots

First install QSFP28 transceivers and then connect fiber optic cabling

to the transceiver ports.

3. SFP28 slots

First install SFP28 transceivers and then connect fiber optic cabling to

the transceiver ports.

1PPS port

Use a coax cable to connect the 1-pulse-per-second (1PPS) SMB port

to another synchronized device.

1. SFP/RJ-45 slots

Combo RJ-45/SFP Ethernet out-of-band (OOB) management port to

provide a network management connection.

2. RJ-45 Console port

Connect the included console cable and then configure the serial

connection: 115200 bps, 8 characters, no parity, one stop bit, 8 data

bits, and no flow control.

3. USB port

Connect using a standard USB cable to a storage device.

Hardware Specifications

Chassis

Size (WxDxH) 477 x 600 x 89 mm (18.78 x 23.62 x 3.50 in)

Weight 16.51 kg (36.40 lbs)

Temperature Operating: 0° C to 40° C (32° F to 104° F)

Storage: -40° C to 70° C (-40° F to 158° F)

Humidity Operating: 5% to 95% (non-condensing)

System Input Rating

AC Input 100-240 Vac, 50-60 Hz, 5.5-2.3 A

DC Input -36 – -72 Vdc, 16-8 A

Power

Consumption

480 W

Regulatory Compliances

Emissions EN 55032:2015+AC:2016, Class A

EN 61000-3-2:2014, Class A

EN 61000-3-3:2013

FCC Class A

Immunity IEC 61000-4-2/3/4/5/6/8/11

EN 55024:2010+A1:2015

EN 55035:2017

Safety UL (UL 62368-1 & CSA C22.2 No. 62368-14

CB (IEC/EN 60950-1, IEC/EN 62368-1)

– 4 –

快速入門指南

E082021-MR-R01

150200002424A

64 連接埠GPON vOLT

ASGvOLT64

2. 機櫃安裝套件—2 個托架和24 個螺絲3. 2 x 電源線4. 控制電纜－RJ45 轉D-Sub

5. 文件－快速入門指南（本文件）及安全及法規資訊

64 x SFP GPON

連接埠

2. 2 x QSFP28 40G/100G 連接埠3.

8 x SFP28 10G/25G

連接埠

4. 系統LED

5. 1 x SFP 管理埠6. 1 x 1PPS

7. 1 x RJ45 管理埠8. 1 x RJ45 控制埠9. 1 x USB 連接埠10. 2 x AC PSU

11. 4 x 風扇托盤11

110

1610

包裝內容物簡介

SFP GPON 連接埠LED：綠燈( 上行鏈路與運作中)、藍燈( 停用)、紅燈( 故障)、閃爍( 活動)

QSFP28 連接埠LED：綠燈(100G)、藍燈(40G)、橘燈(4G)、閃爍

(活動)

SFP28 連接埠LED：綠燈(25G)、藍燈(10G)、橘燈(1G)、閃爍( 活動)

UID LED：閃爍藍燈風扇LED：關閉( 良好)、紅燈( 故障)

空氣濾清器LED：關閉( 良好)、紅燈( 更換濾網)

PSU LED：綠燈( 良好)、紅燈( 故障)

警報LED：綠燈( 良好)、藍燈( 次要)、紅燈( 主要)

狀態LED：綠燈( 良好)、藍燈( 初始化)、紅燈( 故障)

1PPS LED：綠燈(良好)

系統LED 連接埠LED

1 2 3 4 5

*150200002424A_R01*

www.edge-core.com

2.B2F 氣流安裝後至前(B2F) 氣流風扇托盤（藍色握把）及PSU （藍色釋放桿）。更換風扇托盤1.

鬆開風扇托盤螺絲。

2. 從機殼內取出風扇托盤。3. 安裝氣流方向相符的替換風扇。更換PSU

取下電源線。

2. 按住釋放桿並取出PSU。3. 安裝氣流方向相符的替換

PSU。1.F2B 氣流移除前至後(F2B) 氣流風扇（紅色握把）及PSU （紅色釋放桿）。

更換FRU 氣流反向

快速入門指南

– 5 –

安裝裝置將裝置接地連接電源1.

連接

RTN

回路。

(

紅線

)

。

2. 連接-36 – -72 VDC ( 黑線)。3. 連接底座接地( 黃綠線)。確定裝置電源進行網路連線

警告：

為確保安全且可靠的安裝，請使用裝置隨附的配件與螺絲。使用其他來源的配件與螺絲可能導致配件損壞。使用未經許可配件所造成之損壞，不在保固範圍內。

注意：

裝置包含安裝在機箱中的插入式電源供應器(PSU)

和風扇托盤模組。確定所有已安裝之模組氣流方向一致。

注釋：

裝置具有預載於交換器上的開放網路安裝環境

(ONIE) 軟體安裝程式，但沒有交換器軟體映像檔。關於相容交換器軟體的資訊，可上此網站：www.edge-

core.com。

注釋：

模組名稱與核定標誌皆顯示在裝置底部的產品標籤上。

1. 安裝托架使用內附的螺絲安裝左右托架。2. 安裝裝置將裝置裝到機櫃中並用機櫃螺絲固定。

確保機架接地確認安裝裝置之機櫃已正確接地，且符合ETSI ETS 300 253。確認與機櫃接地點間有良好的電氣連接性（無油漆或絕緣表面處理）。將裝置接地將#14 AWG 接地線（未隨附）連接至裝置後面板上的接地點。接下來，將接地線另一端連接至機櫃接地。

注意：

使用UL/IEC/EN 60950-1 認證的電源供應器連接DC 轉換器，以及#14 AWG ( 適用於-36 – -72 VDC

PSU)。

注釋：

DC 端子螺絲應鎖緊至6.6 in-lbs 扭矩。

AC 或DC 電源連接兩部AC 或DC PSU 至電源。

檢查PSU LEDs

正常操作時，PSU1 ∕PSU2 LED 應亮綠燈。

1.SFP GPON 插槽首先安裝GPON 收發器，然後將光纖電纜連接至收發器連接埠。

安裝

快速入門指南

– 6 –

連接時序連接埠進行管理連接

2.QSFP28 插槽先安裝QSFP28 收發器，再將光纖電纜連接至收發器連接埠。3.SFP28 插槽先安裝SFP28 收發器，再將光纖纜線連接至收發器連接埠。

1PPS 連接埠使用同軸纜線連接1 每秒脈衝(1PPS) SMB 連接埠至其他同步化裝置。

1.SFP/RJ-45 插槽結合RJ-45/SFP 乙太網路頻外(OOB) 管理埠以提供網路管理連線。2.RJ-45 控制埠連接隨附的控制線，接著配置串列連接：115200 bps、8 個字元、無奇偶（檢驗碼）、1 個停止位元、8 個資料位元，且無流量控制。3.USB 連接埠使用標準USB 纜線至儲存裝置。

硬體規格底座尺寸（寬x 深