Edge-Core MLTG-360 User manual

– 1 –
Quick Start Guide
E032021-MR-R01
www.edge-core.com
60GHz Terragraph Distribution Node
MLTG-360
1.
60GHz Terragraph Distribution Node MLTG-360
2. Weatherproof port cover
3. Pole-mount bracket
4. Steel-band clamp — 5 cm (2 inch) diameter max.
5. Screw kit
6. DC terminal plug
Package Contents
2 3 41
Overview
5
Product Lineup
1. Port cover
2. Pole mounting bracket with steel-band clamp
3. DC power connection.
4. MGMT PoE IN Port: Connects to PoE injector and management
network.
5. PoE OUT LAN Ports: Connect to LAN devices.
6. Uplink SFP+ fiber transceiver port
2
345
1
6
6
Product Name Position of Radios
MLTG-360 A, B, C, D
MLTG-360-3 A, C, D
MLTG-360-2R A, D
MLTG-360-2P C, D
MLTG-360-1 A
Radio B
Radio A
Radio D
Radio C

Quick Start Guide
– 2 –
Ground the MLTG-360
Make Network Connections
Attach the Port Cover
Mount the MLTG-360
a. Attach the Pole-Mount Bracket
b. Mount on a Pole
Warning: For a safe and reliable installation, use only the
accessories and screws provided with the device. Use of other
accessories and screws could result in damage to the unit. Any
damages incurred by using unapproved accessories are not
covered by the warranty.
Avertissement: Pour une installation sûre et fiable, utilisez
uniquement les accessoires et les vis fournies avec l’appareil.
L’utilisation d’autres accessoires et vis pourrait endommager
l’appareil. Les dommages causés par l’utilisation d’accessoires
non approuvés ne sont pas couverts par la garantie.
Note: Make sure the grounding and lightning protection
conform to local standards.
1
Ground the MLTG-360 by connecting a ground wire to the grounding
point on the MLTG-360 and to nearby good earth.
2
RJ-45 MGMT and LAN Ports
Connect outdoor-rated Category 5e or better cable to the
1000BASE-T RJ-45 MGMT PoE IN port.
(Optional) Connect other network devices to the PoE OUT
1000BASE-T LAN ports. The LAN1 port supports 54V PoE power,
and the LAN2-LAN4 ports support 24V PoE power, only when the
MLTG360 is powered via DC Power.
SFP+ Uplink Port
Install a 10G fiber transceiver in the Uplink SFP+ port and then
Note: It is strongly recommended the MLTG-360 be mounted
on the top of the pole without any obstructions above it. Where
impossible, consider using the optional J-bracket mount,
designed to mount the MLTG-360 aside the pole.
Attach the weatherproof port cover to the MLTG-360 using the screws
provided in the screw kit.
3
4
Attach the pole-mount bracket to the MLTG-360 using the screws
provided in the screw kit.
Place the MLTG-360 on the top of a 4–5 cm (1.57–2 inch)
diameter pole.
Installation

Quick Start Guide
– 3 –
c. Clamp to the Pole
Optional J-Mount Bracket Installation
Connect Power
Verify Power is On
Access the Web User Interface
Note: DC power and PoE power cannot be connected at the
same time.
Feed the provided steel-band clamp through the pole-mount
bracket and around the pole, and then tightly fasten it to secure the
MLTG-360 to the pole.
An optional J-mount bracket is available for installation on poles of
up to 10”. It is sold separately as ICC-J-BRACKET.
5
a. DC Power
Wire the included DC terminal plug to a 44-57 VDC, 4.0 A source to
provide power to the MLTG-360.
b. PoE Injector
The MGMT PoE IN port connection provides power to the unit through
a PoE power injector. The PoE injector must be a passive (non-IEEE)
injector that can provide at least 90 W at 56 V.
Note: PoE OUT on LAN Ports is only available when the
MLTG-360 is powered via DC power.
6
Check the LED
The “C” power LED should stay on after boot-up when operating
normally.
7
1. Connect a PC directly to the MLTG-360’s MGMT port.
2. Set the PC IP address to be on the same subnet as the MLTG-360
MGMT port default IP address. The PC address must start at
192.168.1.x with subnet mask 255.255.255.0.
3. Enter the MLTG-360’s default IP address of 192.168.1.20 into
the web browser address bar.
4. Log in to the web interface using default settings:
Username = admin
Password = admin

Quick Start Guide
– 4 –
Safety and Regulatory Information
FCC Class A
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device is not to be operated on aircraft except for the conditions
listed on FCC CFR 15.255 (b).
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 40 cm between the radiator and your
body.
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
This device complies with ‘Innovation, Science and Economic
Development (ISED) Canada’ license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This radio transmitter [3857A-MLTG360] has been approved by
Innovation, Science and Economic Development Canada to operate with
the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater
than the maximum gain indicated for any type listed are strictly prohibited
for use with this device.
Cet appareil numérique de la classe A est conforme à la norme NMB-
003 du Canada.
Cet appareil est conforme aux normes RSS exemptes de licence
«Innovation, Science et Développement économique (ISDE) Canada».
Son fonctionnement est soumis aux deux conditions suivantes: (1) cet
appareil ne doit pas provoquer d'interférences, et (2) cet appareil doit
accepter toute interférence, y compris les interférences susceptibles
d'entraîner un fonctionnement indésirable de l'appareil.
Cet émetteur radio [3857A-MLTG360] a été approuvé par Innovation,
Sciences et Développement économique Canada pour fonctionner avec
les types d'antenne énumérés ci-dessous, avec le gain maximal autorisé
indiqué. Les types d'antenne non inclus dans cette liste qui ont un gain
supérieur au gain maximum indiqué pour tout type répertorié sont
strictement interdits pour l'utilisation avec cet appareil
.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 40 cm between the
radiator and your body.
This device is not to be operated on aircraft except for the conditions
listed on ISED RSS-210 Annex J.1.
CE Statement
This equipment complies with EU radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 70 cm between the radiator and your
body.
All operational modes:
60 GHz: 802.11ad, 802.11ay
The frequency and maximum transmitted power limit in EU are listed as
below:
57-66 GHz: 40 dBm
The abbreviations of the countries, as prescribed in above table, where
any restrictions on putting into service or any requirements for
authorization of use exist.
CE Mark Declaration of Conformance for EMI and Safety (EEC)
This information technology equipment is in compliance with the
Directive 2014/53/EU and Directive 2014/35/EU.
The Declaration of Conformity (DoC) can be obtained from
www.edge-core.com -> support -> download.
Japan VCCI-A Statement
Antenna Type Antenna Gain (dBi)
Integrated 28
AT BE BG CH CY CZ
DE DK EE EL ES FI
FR HR HU IE IS IT
LI LT LU LV MT NL
NO PL PT RO SE SI
SK TR UK

Quick Start Guide
– 5 –
Warnings and Cautionary Messages
Warning: This product does not contain any serviceable user
parts.
Warning: Installation and removal of the unit must be carried
out by qualified personnel only.
Caution: Wear an anti-static wrist strap or take other suitable
measures to prevent electrostatic discharge when handling this
equipment.
Caution: Do not plug a phone jack connector in the RJ-45
port. This may damage this device.
Caution: Use only twisted-pair cables with RJ-45 connectors
that conform to FCC standards.
Hardware Specifications
AP Chassis
Size (WxDxH) 19.9 x 19.9 x 20.0 cm (7.83 x 7.83 x 7.87 in)
Weight 3.9 kg (8.6 lb) with bracket
Temperature Operating: -20° C to 55° C (-4° F to 131° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity Operating: 5% to 95% (non-condensing)
Network Interfaces
Ports 1 x MGMT PoE IN RJ-45 Port: 1000BASE-T, PoE PD
1 x Uplink Port: 10G SFP+
4 x LAN RJ-45 Ports: 1000BASE-T (PoE OUT)
60 GHz 4 x 60GHz Radios, 802.11ad/ay
Power Supply
PoE Input
Power
44-57 VDC, 1.44 A (Passive PoE)
Power
Consumption
90 Watts max.
Regulatory Compliances
Radio EN 302 567 V2.1.1
EN 62311 (MPE)
47 CFR FCC Part 15.255
ICES-003 Issue 6 Class A RSS-247
RSS-210 Issue 10
RSS-Gen Issue 5
RSS-102 Issue 5 (MPE)
MIC Article 2 Paragraph 1 Item 19—4-2
Emissions EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
Part 15 subpart B Class A (ANSI C63.4-2014)
ICES-003 Issue 6
VCCI-CISPR 32
Safety EN 62368-1: 2014+ A11: 2017
IEC 60950-1: 2005, AMD1: 2009, AMD2: 2013
IEC 60950-22: 2016
IEC 60529-1: 1989+ AMD1: 1999+ AMD2:
2013CSV (IP66)