Edge Lighting Greta LED GRETA-W-L1 Series User manual

SAVE THESE INSTRUCTIONS!
GRETA-W-_-L1-_
M2-IND-_
Installation Instructions for Greta LED
904-GRETA-W-L1-04
IMPORTANT INFORMATION
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: [phone]
Fax: [phone]
www.edgelighting.com
[email protected]
1
Disassemble the Fixture
A
SCREW HEAD
SLOT
1: Remove the Phillips screw on one end of the shade and slide
the shade off the backplate.
PHILLIPS SCREW
1
SHADE
BACKPLATE
2: Remove the LED mounting plate by loosening the six 1.5mm screws using an M3 Allen wrench.
B2
1.5MM SCREW
LED MOUNTING
PLATE
NUT
MOUNTING
POST
BACK PLATE
C3: Loosen and remove two nuts from the threaded posts
4: Remove the fixture back plate from the mounting plate.
3
- Use this fixture indoors only.
- This product is ETL listed for damp locations.
- This product is wall mounted only.
- This product can mount to either a 4" square junction box
with round plaster ring or an octagon junction box.
- This product can be dimmed with a standard low-voltage
electronic dimmer.
- This product must be installed by a qualified electrician.
- Before beginning any electrical work, ensure that
power to the junction box is turned OFF.
1
4
© 2015 Edge Lighting. All Rights Reserved.

2
Install the Fixture
4: Feed the LED power wires through the mounting plate center
cutout.
5: Place the mounting plate to the junction box and level
mounting studs.
6: Secure the mounting plate to the junction box using two
LED TRANSFORMER
WIRE NUT
JUNCTION BOX
1: Connect the white LED transformer wire to the neutral
power wire with a wire nut.
2: Connect the black LED transformer wire to the hot power
wire with a wire nut.
3: Place the LED transformer and all wire connections inside
D
7: Feed the LED transformer power wires through the strain
relief center hole of the backplate and canopy.
8: Place the back plate and canopy on to the mounting posts
and tighten both nuts securely.
21
NOTE: It is recommended more than one person assist with
installing this fixture.
MOUNTING
PLATE
E
JUNCTION
BOX HOLE
#8-32 SCREW
NUT
MOUNTING
POST
BACK PLATE
F
8
45
6
7
9: Align the backplate screw holes to the electrical box
mounting holes, and place the backplate on wall to mark
the anchor location.
10a: If mounting fixture centered: mark the end holes on
the wall. These marked holes are for anchors.
10b: If mounting fixture off centered: slightly loosen the
two backplate screws and slide the backplate to the
desired position and tighten the backplate screws. Mark
the end holes of the backplate on the wall. These marked
ADJUSTMENT
BACKPLATE
SCREW
BACKPLATE
END
HOLE
MOUNTING
PLATE
10a 10b
G

3
11: Remove the backplate from the wall and tap the anchors
on the marked points up to the threaded portion with a
hammer. Screw in the threaded portion of the anchors with
a Phillips screwdriver.
12: Repeat steps 7 and 8 (refer to Figure F on Page 2).
13 Secure the ends of the backplate to the anchors with the
two #8 screws.
WALL
ANCHOR
H
11
11
K
16: Lay the LED module wires and connections between the LED module plate and mounting rail.
16
MOUNTING RAIL
LED POWER WIRES
CANOPY
LED MODULE PLATE
13
12
I
JBACK PLATE
CANOPY
14 15
14: Connect the red LED Module wire to one of the transformer
wires (either one) with a wire nut.
15: Connect the black LED module wire to the other
transformer wire with a wire nut.

17: Replace the LED module plate by rotating and placing it on the mounting rail, making sure all wires and wire connections
are under the LED module plate. Replace and tighten the six 1.5mm screw using an M3 Allen wrench.
18: Slide the shade onto the backplate. Replace the Phillips
screw and tighten to secure the shade in place.
4
M
SCREW HEAD
SLOT
PHILLIPS SCREW
18
SHADE
BACKPLATE
18
L17
1.5MM SCREW
LED MODULE
PLATE
17