MPK VisionVent M pro User manual

1 Issue 01.2021
MPK Metall- und
Plastikverarbeitung GmbH & Co. KG
Friedrich-Ebert-Str. 298-300
D-58566 Kierspe
mpk-kierspe.de
Rooflight with pleated blind and net
for installation in caravans and mobile homes
VisionVent M pro LED
Technical data:
EN Installation and Operating Instructions
Please read the instructions carefully before installing the rooflight and store
it for future.
We cannot be held responsible for incorrect fitting, handling or operation.
Any product faults relating to the production and materials used should be notified to us via
an authorised dealer immediately.
Included with delivery
1x Rooflight with outer frame
1x Inner frame with LED, polyswitch fuse, connection cable
1x Fixing parts (8x fixing brackets and 4x large plastic screw)
Additionally required for installation (not included in delivery)
1x Elastic sealant adhesive, e.g. Dekalin Dekaseal 8936 or SikaLastomer®-710
8x Fixing screws for the upper frame - Pan 3,5 mm / head according to DIN ISO 7049
(DIN 7981) / The length of the screw should be determined by the roof thickness, plus
approximately 10 mm for the screw to enter the upper frame.
With timber support under the roof lining:
4x Fixing screws for the inner frame:
Pan 3,5 mm / head according to DIN ISO 7049 (DIN 7981) / length max. 10 mm
Explanation of symbols
Safety and installation instructions
Check the roof thickness of your vehicle before mounting.
The rooflight should only be fitted to a flat roof surface, both internally and
externally.
Choose a fitting position that will not interfere with other roof mounted components
(e.g. roof-racks/antenna's etc.) and avoid internally installed electrical cables and
furniture, which could impede the correct operation of the rooflight.
Inner frame
Make sure that there is a suitable supply line and switch for the lighting in the vehicle.
Never stand on the dome of the rooflight!
Do not open the rooflight while driving. The rooflight must be locked down before
traveling.
Do not open the rooflight in strong wind or rain .
Close the rooflight during rain and snowfall.
Aperture
400 x 400 mm
Roof thickness
24-56 bzw. 42-70 mm
Corner radius
23 mm
Site dome
560 x 560 mm
Height over roof
96 mm
Ventilation
150 cm²
Weight
4,0 kg
Size inner frame
565 x 530 x 35 mm
Outer frame material
Polypropylene
Dome material
PC + SAN
Speed limit
130 km/h
Authorization
ECE R43 -019650
LED-light
394 x 9 x 2,5 mm
Light color
~ 3000 K (warmwite)
Energy efficiency class
A+
Nom. useful liminous flux
2 x 390 lm
Voltage
12 -14V DC
Condumption
2 x 4,2 kW/h / 1000h
Nominal lifetime
10.000h
No. of switching cycles
50.000
Warm up time
<1sek.
Nominal beam angle
60°
NOTE
Particulary important information.
ATTENTION!
Failure to observe can lead to material damage.
WARNING!
Safety note: Serious risk of injury.

2 Issue 01.2021
Installation
Please clean the frames carefully before mounting the
sealant.
Follow the instructions of the sealant manufacturer.
Separate the inner and outer frames and fit the outer frame
to the outside of the roof aperture onto a bed of sealant.
The operating handles facing the front and rear of the
vehicle!
Place over the screw holes on the inside of the frame, the 8
fixing brackets; four in each corner, four in the centre of each
side. Secure with screws, stop as soon as the brackets start to
distort.
Max. Torque 0.5 Nm.
Remove the small tabs on the corner bracket before installing
the inner frame.
To fit the inner frame, gently pull out the pointed ends of the
cover profiles to release them and reveal the fixing points.
Turn off the power supply in the vehicle before
proceeding with the connection of the LED lighting.
Connect the supplied connection cable to the power supply
installed in the vehicle.
Connect the Polyswitch cable of the inner frame to the power
supply of the vehicle. Then place the inner frame in the centre
of the cutout.
Version 1: Timber support under the roof lining
Offer up the inner frame into the outer frame. Use the four small
holes to fix the inner frame withstandard screws into the timber
support.
Version 2: Inner lining made of plywood / polyester layer
Offer up the inner frame into the outer frame and mark drill
holes (large screw hole).
Pre-drill the screw holes and screw the inner frame tight with
the supplied plastic screws.
Fix the connector from the inner frame with the connector from
the side panel before inserting the side cover.
Refit the inner frame covers by locating the securing lugs
and keeping the covers parallel against the roof whilst sliding
them carefully onto the frame, ‘clicking’ back into position,
without distorting.
Operation
To open the rooflight, press both locking buttons and push the handles upwards.
The rooflight can be opened fully by the handles or in four different directions, so that the
dome can be angled against driving weather conditions.
To close the rooflight, press the locking buttons again and pull the handles down. The roof
hood is locked.
Keep the pleated blinds open while driving to avoid driving noise and damage
from the airstream.
To avoid heat accumulation do not close blind completely during the day. Open
both pleats when not using the vehicle.
Var.1
Var. 2

3 Issue 01.2021
Cleaning For easier cleaning of the dome it can be removed from the frame
by releasing the four screws holding the handle arms.
Never remove the screws holding the dome and the
handles together. These are secured by a torque
screwdriver and should only be handled by an approved
dealer.
Use only clear water and a soft sponge. Solvents may attack the
plastic and make it brittle.
Clean the gaps by immersing the hood in a container filled with
water. Let the dirt soak a little.
Use the two handles to pull the hood through the water so that the
dirt can be washed out.
Make sure that only the original screws are used when
replacing the dome and they enter the thread in the plastic
correctly. Do not over-tighten.
Clean the pleated blinds with a soft brush, dry cloth or feather duster.
We strongly advise against wet cleaning, as this can damage the insect screen and
blackout pleated blind.
Extras (optional)
Designation
Article No.
Adapter frame for Fiat Ducato
4040ARW
Warranty
The legal warranty applies.
mpk-kierspe.de/Downloads