Edge Products Juice User manual

installation Instructions
installation Instructions
Dodge Juice
Dodge Juice
**read important safety information in this manual**
**read important safety information in this manual**

TABLE OF CONTENTS Installation Instructions
2
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
Table Of Contents
INTRODUCTION ........................................ 4
PRODUCT REGISTRATION ............................................. 4
IMPORTANT NOTES ...................................................... 5
ABOUT THE JUICE ....................................................... 6
INSTALLATION.......................................... 8
1998.5 - 2002 5.9L (24V) .......................................... 8
CONNECTING TO CONSTANT POWER .............................. 9
CONNECTING TO GROUND ........................................... 10
CONNECTING TO KEY-ON POWER .................................. 10
CONNECTING TO MAP SENSOR ..................................... 11
CONNECTING TO DATA LINK ......................................... 11
CONNECTING TO INJECTION PUMP................................ 12
BOOST ELBOW INSTALLATION ...................................... 13
“LIFT PUMP” FUEL PRESSURE SENSOR INSTALL ............ 14
FUEL SYSTEM BLEEDING INSTRUCTIONS ....................... 15
CONNECTING TO TRANSMISSION (AUTOMATIC) ............... 16
CONNECTING TO TRANSMISSION (STANDARD) ............... 17
2003 - 2004 5.9L (CR) ............................................ 18
CONNECTING TO POWER .............................................. 19
CONNECTING TO GROUND ........................................... 20
CONNECTING TO INJECTORS ........................................ 20
CONNECTING TO MAP SENSOR ..................................... 21
CONNECTING TO DATA LINK ......................................... 21
CONNECTING TO FUEL PRESSURE SENSOR ................... 22
BOOST ELBOW INSTALLATION (OPTIONAL) ..................... 22
2004.5 - 2005 5.9L (600) ......................................... 23
CONNECTING TO POWER .............................................. 24
CONNECTING TO TURBO TIMER ..................................... 25
2006 - 2011 5.9L & 6.7L......................................... 26
CONNECTING TO POWER .............................................. 27
CONNECTING TO GROUND ........................................... 29
CONNECTING TO INJECTORS ........................................ 29
CONNECTING TO MAP SENSOR (2006 - 2007 5.9L ONLY) 30
CONNECTING TO DATA LINK ......................................... 30
CONNECTING TO THE TURBO TIMER .............................. 31
2007.5-2011 6.7L (RACING) ..................................... 33
DPF EGT SENSOR INSTALLATION .................................. 34
EGR “SPOOFER” INSTALLATION ................................... 35

TABLE OF CONTENTS
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
3
Installation Instructions
Dodge Juice
EGT PROBE INSTALLATION.........................................36
TAPPING AND PROBE INSTALLATION............................. 36
CONNECTING THE PROBE TO JUICE .............................. 38
JAB INSTALLATION ...................................................39
1998.5 TO 2011 - JAB INSTALLATION ............................ 39
2006-2011 OBDII CONNECTION .................................... 41
JUICE MODULE INSTALLATION ................................... 41
FINAL JUICE MODULE INSTALLATION ............................ 41
MOUNTING AND SECURING THE JUICE .......................... 42
FINAL INSPECTION....................................................42
OPERATING INSTRUCTIONS ..................... 43
USING THE JUICE ....................................................43
APPENDIX .............................................. 44
ENGINE COMPARTMENT(REFERENCE) .........................44
1998.5 - 2002 ............................................................ 44
2003-2005 ................................................................ 45
2006 - 2011 ............................................................... 46

INTRODUCTION Installation Instructions
4
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
PLEASE take the time to register your product on line at edge-
products.com. Follow the instructions at link: http://www.edge-
products.com/product_registration.php
BENEFITS OF PRODUCT REGISTRATION
-Your Safety - Registering your product allows us to know exactly
which product you have and provide important product updates to
you that improve the quality and/or safety of the product.
-Enhanced Features - Almost all Edge products are easily updated
via the internet. We are constantly adding new features and im-
provements to our product that we know you will want to enjoy.
-Confirmation of Ownership - Provides a record in case of prod-
uct loss, theft, or required warranty work. When you call us for
support our team will already have much of the information they
need to help you.
-Improved Product Development - Helps us better understand
you (our customer) and design products that meet your needs.
-Special Offers - Allows us to inform you about special offers on
accessories and/or new products that fit your vehicle and enhance
your driving experience.
P R O D U C T R E G I S T R A T I O N
PRODUCT REGISTRATION

INTRODUCTION
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
5
Installation Instructions
Dodge Juice
I M P O R T A N T N O T E S
IMPORTANT NOTES
1. If you have used another tuner/programmer on
your truck, you will need to program your truck
back to stock before using the Attitude or Juice.
Failure to return to stock may result in PCM failure or engine
damage.
2. Programming your vehicle may expose existing defects in your
vehicle’s PCM that could disable your vehicle. It is advised that
you do not program your vehicle in remote location in case of
vehicle failure.
3. All Edge modules and programmers are built to operate with
OEM calibrations. When you take your vehicle to a service center
they may, by your request or otherwise, update your vehicle’s
calibrations. Therefore it is important that you return your vehicle
to stock before taking it in for service. Edge updates its active
products (i.e. those currently being manufactured) to work effec-
tively with updated OEM calibrations. However, this process can
take some time as Edge is not always made aware of calibration
changes made by the OEM. In the case of discontinued products,
Edge cannot ensure that your unit will work effectively if you take
your vehicle to a dealership and you are given, by your request or
otherwise, a new calibration.
4. For specific information regarding horsepower, torque, and
other features available for this product:
(1) Go to www.edgeproducts.com
(2) Type the part number of your product in the “KEYWORD/
PART# SEARCH” and press enter.
(3) Click the link under “Description”
(4) Scroll down to the “DOWNLOAD VEHICLE SPECIFIC HORSE-
POWER, TORQUE,AND FEATURES CHART” link and click on it.
(5) Find the information that is specific to your make and model.

INTRODUCTION Installation Instructions
6
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
Congratulations on purchasing the Edge Juice/Attitude system for
the Dodge Cummins Diesel®.
The Juice/Attitude system features an intelligent module (Juice)
that acts as an add-on Engine Control Module (ECM) for the Cum-
mins Diesel® Engine. This module is controlled and customized
in the cab of your truck by the Attitude monitor/controller.
This system offers many cutting-edge, additional features not
available with the factory setup. Since the Juice Module is an add-
on ECM, it uses data from your truck’s computer or engine control
module (ECM), and then enhances the factory settings to optimize
your truck’s performance. This product offers a wide variety of
amazing performance and safety features that can ensure you get
the driving experience you desire without damaging your truck.
Please take the time to thoroughly review all of the features and
product options outlined in this manual. Taking the time to un-
derstand how this product works and how to properly operate this
product will ensure that you have an extraordinary and safe driving
experience. If we can be of any assistance to help you get the most
from your product please call us at 888-360-3343. We are open
Monday through Friday from 8am to 5pm Mountain Time.
A B O U T T H E J U I C E
ABOUT THE JUICE

INTRODUCTION
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
7
Installation Instructions
Dodge Juice
IMPORTANT: Read all Safety, Warranty, and Installation In-
structions in this manual and the CS/CTS User Guide before in-
stalling this product. Read through these instructions completely
so that you understand each step prior to installation.
SAFETY TERMS
Throughout this User Guide (hereafter noted as User Manual or
Manual) you will see important messages regarding your safety or
the protection of your vehicle. These messages are designated by
the words WARNING or CAUTION.
WARNING indicates a condition that may cause serious
injury or death to you, your passengers or others nearby. Pay
careful attention to these Warning messages, and always comply
with them. They could save a life.
CAUTION indicates a condition that could cause damage to your
vehicle. It is important to install and operate your EDGE prod-
uct in conformance with instructions in this Manual. Caution
alerts you to particularly important things that will keep your
vehicle operating properly.

INSTALLATION Installation Instructions
8
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
Supplied Items Qty Required Tools
-Knife
-2 to 3 ft of wire (fishing)
-Needle nose pliers
-Phillips screwdriver
-Flat tip screwdriver
-3/8” Drive Torque Wrench
-1/2” Wrench
-3/8” Drive Ratchet
-1/4” Socket
-5/16” Socket
-7/16” Deep Well Socket
-10mm Socket
-13mm Socket
-1/8” NPT Tap
-5/16” or 21/64” Drill Bit
1 9 9 8 . 5 - 2 0 0 2 5 . 9 L ( 2 4 V )
1998.5 - 2002 5.9L (24V)
1 Main Wiring Harness...................(1)
2 Edge Juice Module.......................(1)
3 Adapters.......................................(1)
4 Zip Ties ......................................(10)
5 Hose Clamp..................................(1)
6 Brass Fitting.................................(1)
7 Leaded Fuse Link.........................(2)
8 Velcro Strips..................................(2)
9 Fuel Pressure Sensor....................(1)
10 Temperature Sensor......................(1)
11 EGT Probe...................................(1)
12 Banjo Bolt...................................(1)
13 Washer.........................................(2)
14 CS/CTS Kit.................................(1)
1
2 43
6 7
5
8
9 10 11
12 13
2000 (Data Link)
2001-2002 (MAP)
Note: Depending on your year of truck, you may not need everything provided.
14
REFER TO QUICK
INSTALL GUIDE
FOR INSTALL

INSTALLATION
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
9
Installation Instructions
Dodge Juice
Ground Connector (Black)
Injection Pump Connector
Key-On Power Connector - Yellow (Required at all times)
Transmission Temp Sensor Connector(Purple/White)
Data Link Connector
MAP Connectors EGT Probe Connector
Attitude Connector
Fuel Pressure Connector
Constant Power Connector -
Red (Required for Turbo Timer
Install, otherwise Optional).
Harness Connection Guide
Figure 2
NOTE: DO NOT reconnect battery until installation is complete. Connecting
power may cause fault code in the ECM.
Figure 1 - (Data Link and MAPconnectors may vary from this view de-
pending on your vehicle year. If this is the case, you will need to use the
supplied adapters.)
WARNING An electrical charge or battery acid can burn you. Battery
gas can explode or ignite. Take care when working around the battery. Follow
instructions in the vehicle owner’s manual for disconnecting and reconnecting a
battery.
Main Juice
Connector
1. Using the ½” wrench, loosen both negative battery cables.
2. Remove cables from the battery posts and set aside.
3. Locate and remove the 10 Amp “A/C Clutch” fuse from
inside the engine compartment fuse panel.
4. Insert the Leaded Fuse link (see Figure 2). The leg with the
wire soldered to it needs to plug into the “HOT” side of the
fuse location. Orient the fuse exactly as shown in Figure 3 on
the following page.
5. From the main harness, connect the Red Constant Power Connector to the
installed Fuse Link (Figure 3)
CONNECTINGTOCONSTANTPOWER
(Required for proper Turbo-Timer functionality)
i

INSTALLATION Installation Instructions
10
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
Figure 3
Fuse Diagram (Engine
Compartment)
Figure 4 - Driver Side Fuse Panel
Fire wall
Routed Cable
Grommet
CONNECTINGTOGROUND
1. Connect the Ground Connector to the NEGATIVE side of the battery.
1. Cut a 1/2” slit in the fire wall grommet.
NOTE: Automatics - easy access is the clutch hole grommet located to the left
of the fire wall brake hole. Manuals or Automatics- Use the large vehicle wir-
ing harness grommet on the fire wall.
2. Route the Yellow Key-On Connection from the engine compartment to inside
the cab through the cut hole from step 1.
3. Locate and remove Fuse 9 (10 Amp) from inside the driver side fuse panel.
4. Insert the Leaded Fuse link (see Figure 2). The leg with the wire soldered to
it needs to plug into the “HOT” side of the fuse location. Orient the fuse exactly
as shown in Figure 4 below.
5. Connect the Yellow Key-On (routed in step 2) to the installed Fuse Link.
CONNECTINGTOKEY-ONPOWER
FUSE 9
To Fire-wall

INSTALLATION
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
11
Installation Instructions
Dodge Juice
1. Disconnect the stock wiring harness from the boost sensor located at the rear
of the fuel filter housing (Near the top of and on the engine block). See Figure 5
2. Plug the Edge harness MAP connectors in between the truck MAP sensor and
the truck MAP sensor cable. (Figure 6)
NOTE: The MAP sensor ‘T’shown in Figure 6 is for the 1998.5 - 2000 Juice.
The 2001 and 2002 harnesses have different sensor connectors, but in the
same location. Refer to Figure 5 for truck connector locations.
Figure 5 - Connector
Locations Figure 6 - “T”Assembly
Figure 5 Connecto
r
98.5-02 MAP Sensor
98.5-99 Data Link
Truck Harness
Edge MAP Connectors
Sensor (Engine Side)
CONNECTINGTODATALINK
1. Locate the Data link connectors:
• 1998.5 - 1999: The triangle shaped connector is located on the driver’s side
of the engine in the wiring harness near the power steering pump.
• 2000 - 2002: The three pronged flat connector is located on top of the fuel
lift pump that is located on the driver’s side of the engine directly below the
MAP sensor. (The 2000 must use the 2000 Data link Adapter.)
NOTE: On some 2001 trucks the Data Link connector can be located on the
driver’s side of the engine in the wiring harness near the power steering pump.
2. Replace the protective plug on the truck Data Link with the Juice harness
Data Link Connector. (Refer to Figure 5 above)
CONNECTINGTOMAPSENSOR
g
00-02 Data Link

INSTALLATION Installation Instructions
12
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
Figure 8 - VP44 Fuel Pump
Figure 7 - Throttle Position Housing
2. Using a sharp knife or razor, care-
fully slice back the insulation that cov-
ers both pump wires contained in wire
bundle number one (see figure 8).
NOTE: This will be the wire on the top, closest to the engine block when the
pump is installed on the truck.
Wire Bundle 1
4. Unscrew the “top” of the Posi-Tap® and place the wire to be tapped in the
slot provided in the cap.
1. Unbolt and remove the casting that
attaches to the Throttle Position Sen-
sor (TPS) housing to expose the fuel
pump and the associated control wire.
(Figure 7)
NOTE: Although attaching the Juice cable to the VP 44 pump control wire
is optional; not tapping into the VP 44 pump prevents the Juice module from
increasing the output of the Cummins engine to it’s full potential and will
result in limited horsepower and torque gains. In order to control the pump
more directly, the Juice module needs to be electrically attached to the VP 44
pump. In order to attach the module to the VP 44 pump, the control wire must
be pierced with the Posi-Tap® wire provided on the Juice harness.
The following figures 7-9 show how to connect the Juice to the Bosch VP 44
high pressure pump and how and where to attach the Posi-Tap® connection.
Figure 8 is a Bosch VP 44 pump that has been removed from a truck. This is
the same pump used on Cummins engines for model year trucks from 1998.5
to 2002.
3. Locate the TOP injection pump wire
identified in Figures 8 & 9.
Remove
CONNECTINGTOINJECTIONPUMP
Wire Bundle 2 (Do Not Modify)
(Modify this wire)

INSTALLATION
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
13
Installation Instructions
Dodge Juice
5. Place a single drop of RTV
Silicone Sealer in the CAP of
the Posi-Tap®. There should be
enough silicone sealer so that
when the cap is installed on the
Posi-Tap® body some of the
sealer is pushed out around the
edges of the wire. The sealer
provides a water tight seal in and
around the connection.
Figure 9 - PosiTap® Pre-Twist
6. Pre-twist the body of the
Posi-Tap® counter clockwise
with about seven full turns before
twisting on to cap. (See figure 9)
NOTE: This will pre-load the wire so that when the body of the Posi-Tap®is
installed on the cap, the wire will not remain twisted in the wire harness.
7. Twist harness onto cap until tight.
BOOSTELBOWINSTALLATION
2. Remove the hose and set it aside.
3. Using the pliers, remove the crimp style clamp from the hose on the brass
fitting located on the now exposed lower front side of the turbocharger.
4. Remove the hose from the brass fitting and dispose of the crimp style clamp.
5. Using the 7/16” wrench, unscrew the stock brass fitting out of the turbocharg-
er housing.
7. Slip the supplied hose clamp onto the stock hose then install the stock hose
onto the supplied brass fitting and tighten the hose clamp with the ¼” socket.
8. Reinstall the stock air hose onto the air filter housing and turbocharger inlet.
9. Using the 5/16” socket, tighten both clamps securely.
1. Using the 5/16” socket, loosen the two clamps securing the air induction hose
to the air filter housing and the turbo inlet.
Figure 10 - Turbo View
OEM brass fitting
6. Using the 7/16” wrench, install the supplied brass fitting. Tighten while being
careful not to over-tighten.
Cap
Body
NOTE: On some vehicles, there is a solid line and cannot be replaced with a
brass elbow.

INSTALLATION Installation Instructions
14
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
CAUTION: When the Fuel Supply Line is removed, fuel can drain out of the
VP 44 pump, and air can enter the line and/or pump. In order to minimize
the amount of air that is let into the fuel system, pre-install the fuel pressure
sensor onto the supplied banjo bolt before removing the stock banjo bolt from
the pump. Tighten the sensor into the banjo bolt until it is snug.
CAUTION: If you lack experience or tools
to bleed the fuel system take the truck to an
experienced mechanic for installation of the
fuel pressure sensor!
CAUTION: The fuel that is pumped to the
injectors also acts as a lubricant for the Bosch
VP-44 high pressure pump. A loss of fuel pres-
sure to the high pressure pump may result in
permanent damage to the high pressure pump.
2. Remove the stock banjo
bolt from the injector pump
supply line located on the
VP44 with the pre-installed
neoprene washer and fuel
pressure sensor. (Figure 14)
1. Thread fuel pressure sen-
sor into the supplied banjo
bolt.
3. Tighten bolt to the appro-
priate torque specifications
(18 ft-lbs)
Figure 11 - Installed Boost Elbow
Edge Supplied Elbow
Hose Clamp
Hose
“LIFTPUMP”FUELPRESSURESENSORINSTALL
Figure 12 - VP44
Figure 13

INSTALLATION
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
15
Installation Instructions
Dodge Juice
Fuel Pressure Sensor
Edge Banjo Bolt
Washer - Bolt Side
Fuel Supply
Line
Washer - Pump Side
NOTE: Fuel Filter Housing (Optional placement of Banjo bolt for 1999
Trucks only).
Figure 15- Fuel Filter
Method (1999 Only)
4. Once this procedure is complete, tighten the return line banjo fitting to 24 Nm
(18 ft-lbs.) torque.
CAUTION: IT IS CRITICAL THAT THE AIR INTRODUCED INTO THE FUEL
LINE BE REMOVED FOR THE FUEL SYSTEM TO OPERATE PROPERLY.
NOTE: Use this bleeding procedure at the end of the installation. Trying to
bleed the fuel system half way through the installation could cause a check
engine light.
1. In order to remove the air from the system, loosen BUT DO NOT REMOVE
the overflow valve banjo fitting that connects to the return line.
FUELSYSTEMBLEEDINGINSTRUCTIONS
2. Place a shop rag or towel around the banjo fitting to catch excess fuel.
3. Turn the ignition key to CRANK position and quickly release the key to the
ON position.
NOTE: DO NOT START THE ENGINE! The fuel lift pump will operate for
up to 25 seconds.
5. Attempt to start the engine. NOTE: The engine may be very noisy or run
erratic for a few minutes. Keep an eye on the fuel pressure as displayed on the
Figure 14

INSTALLATION Installation Instructions
16
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
1. Unbolt the stock plug from passenger side rear of the transmission using a
7/16 inch (11mm) wrench (see Figure 17).
2. Apply Teflon tape to the threads of the transmission temperature sensor.
3. Using a ½ inch wrench, thread the Edge supplied transmission oil
temp sensor (see parts list) and connect the cable using the supplied nut.
4. From the top of the engine, route the transmission temperature sensor along
the factory wiring harness and over the top of the transmission and secure with
supplied wire ties.
NOTE: Asmall amount of transmission fluid will leak from the outlet.
Figure 16 -Automatic Transmission Figure 17- SensorAssembly
Refers to Fig 16 & 18
Nut
Lock
Washer
Edge
Cable
Washer
Fiber Woven
Washer
Sensor
Insert this
end into
transmission
Truck Front
(Passenger side)
CONNECTINGTOTRANSMISSION(AUTOMATIC)
Attitude. If the pressure drops below 4 psi, or the engine quits running, re-
bleed the fuel system. If the engine still does not start, remove and check the
fuel filter. If the filter is dirty or damaged, replace the filter.
CAUTION:
•Do not engage the starter motor for more than 30 seconds – Allow two min-
utes between cranking intervals.
•Although it is rare, on occasions the LIFT pump may fail to prime after the
banjo bolt has been replaced signifying a possibility of a worn pump. In this
rare instance the LIFT pump should be replaced.
6. Reinstall the throttle bracket onto the fuel injection pump using the three
bolts. Torque these bolt to 18 ft-lbs using a torque wrench and 13mm socket.

INSTALLATION
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
17
Installation Instructions
Dodge Juice
CONNECTINGTOTRANSMISSION(STANDARD)
NOTE: When the Power Take-Off (PTO) plate is removed ALL of the gear
lube from the transmission will drain out – Ensure that you have the COR-
RECT replacement oil prior to removing the PTO plate. See the Dodge service
manual for replacement gear lube type.
1. Using a 14 mm wrench, remove the lowest bolt on the PTO cover plate and
drain the transmission fluid.
2. Unbolt the remaining five bolts to the PTO cover plate and remove it com-
pletely.
3. Using a 5/ 16” or 21/64” drill bit, drill a hole in the PTO cover plate in the
location shown in figure 18.
4. Using a 1/8” NPT tap, thread the hole in the PTO cover plate.
5. Apply Teflon tape or pipe thread sealant to the transmission temperature sen-
sor and thread it into the PTO cover plate.
6. Clean the surface of the PTO cover plate and transmission . Apply an au-
tomotive gasket silicone to the plate surface that will come in contact with the
transmission.
7. Re-attach the plate cover to the transmission and connect the sensor cable to
the sensor.
8. Refill the transmission with fluid.
Figure 18 - Manual Transmission (Driver Side)
Truck Front
(Driver Side)
PTO Cover Plate
Transmission
Bell Housing
NOTE: YOUR JUICE MODULE INSTALLATION IS NOT COMPLETE. RE-
FER TO THE “EGT PROBE INSTALLATION” SECTION TO CONTINUE.

INSTALLATION Installation Instructions
18
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
2 0 0 3 - 2 0 0 4 5 . 9 L ( C R )
2003 - 2004 5.9L (CR)
Supplied Items Qty Required Tools
-3/8” Drive Ratchet
-10mm Socket
-5/16” Socket
-1/2” Wrench
-7/16” Wrench
1 Main Wiring Harness.....................(1)
2 Edge Juice Module.........................(1)
3 Leaded Fuse Link...........................(1)
4 Zip Ties .......................................(10)
5 Velcro Strips...................................(2)
6 EGT Probe......................................(1)
7 Brass Fitting...................................(1)
8 CS/CTS Kit....................................(1)
1
2 43
56
Note: Depending on your year of truck, you may not need everything provided.
7
REFER TO QUICK
INSTALL GUIDE
FOR INSTALL
8

INSTALLATION
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
19
Installation Instructions
Dodge Juice
Harness Connection Guide
Ground Connector
Injector Connectors
Data Link Connector
MAP Connectors
EGT Probe Connection
Attitude Connection
Fuel Pressure Connectors
Power Connector
Figure 1 - Main Wiring Harness
NOTE: DO NOT reconnect battery until installation is complete. Connecting
power may cause fault code in the ECM.
WARNING An electrical charge or battery acid can burn you. Battery
gas can explode or ignite. Take care when working around the battery. Follow
instructions in the vehicle owner’s manual for disconnecting and reconnecting a
battery.
INJ 1&2
INJ 3&4
INJ 5&6
Main Juice
Connector
CONNECTINGTOPOWER
Figure 2
1. Using the ½” wrench, loosen both negative battery cables.
2. Remove cables from the battery posts and set aside.
3. Locate and remove Fuse 50 (10 Amp) from inside the engine
compartment fuse panel.
4. Insert the Leaded Fuse Link (see Figure 2). The leg with
the wire soldered to it needs to plug into the “HOT” side of the
fuse location. Orient the fuse exactly as shown in Figure 3 on
the following page.
5. From the main harness, connect the Red Power Connector to the installed
Fuse Link (Figure 3)
i

INSTALLATION Installation Instructions
20
Dodge Juice
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
TABLEOFCONTENTS INTRODUCTION INSTALLATION OPERATINGINSTRUCTIONS APPENDIX
1. Connect the ground to the vehicle by
removing the 10mm bolt from the driver
side fender, above the battery.
2. Add the black ground connector with
the round terminal to the wires already
on the bolt.
Figure 4 - Ground Connections
Figure 3 - Fuse Box
1. Disconnect all 3 stock injector connectors by squeezing the tab on the top of
each connector. (Figure 6 for locations)
2. Gently insert the Juice ‘T’ Injector Connectors between the stock connectors,
and lock in place. (Figure 5) NOTE: Match Edge Harness connectors to the
proper injector set according to the wire colors described in Figure 6.
CAUTION: When inserting connector bodies. If the connector does not slide
smoothly, remove the connector, inspect the pins, and retry installation.
Ground Connector
Edge Injector Connectors
Truck
Injector
Truck
Harness
Figure 5 - “T”Assembly
CONNECTINGTOGROUND
CONNECTINGTOINJECTORS
Fuse 50
3. Replace and tighten the bolt. (See
Figure 4)
To Fire-wall