Edge Products CS User manual

Supplied Items Suggested Tools
CS or CTS Device1.
Arkon Windshield Mount2.
OBDII Cable3.
Mini USB Cable4.
CD5.
Alcohol Wipe6.
Zip Tie Packet7.
Flat head screwdriver•
1
23
45
67
The OBDII port is a 16-pin connector like the illustration be-
low.
The OBDII port is located un-
der the dash below
the steering wheel.
The OBDII port is
placed in dierent
locations under the
dash for dierent
applications; refer to
the OBDII port loca-
tion drawing (left) to
help you locate your
OBDII port.
*07 + Ford Superduty OBDII
port is located on the left side
of the wheel instead of the right.
*94-97 Ford Powerstroke OBDII port
is located on the passenger side below
and to the left of the glove box.
FORD
DODGE
GM-CHEV
Once you’ve removed
the necessary panels,
connect the OBDII
cable to the OBDII
port, and route the
cable under the dash,
out the side panel, up be-
tween the door seal trim
and the edge of the dash.
Tuck the cable back as far
as you can as you route it
up to the dash.
Remove the panel on the
side of the dashboard to
provide access to route
the OBDII cable from the
OBDII port up to the top
of the dash.
*On some vehicles you may also
need to remove the panel directly
under the steering wheel.
*Note: Leave 6-10”
of cable exposed on
top of the dash so you
have room to posi-
tion the device.
OBDII PORT
Position the device
and the mount on
the windshield in the
desired location.
Pay attention to
where the suction
cup will mount on the
windshield.
Once you’ve identied
the suction cup position
on the windshield, use
the supplied alcohol wipe
to thoroughly clean the
area. After you’ve wiped
the area clean, let it dry
for 2-3 minutes.
Before you attach the suc-
tion cup portion of the
mount to the window
attach it to the device.
Insert the tabs on the
mount into the slots on
the back of the device and
slide up (CTS) or to
the side (CS) until it
stops.
*The mounting tabs are a tight
t by design to maintain
a solid connection.
Next, insert the connector on the end
of the OBDII cable into the 16-pin
connector on the back of the device
(this is easier if done prior to mount-
ing the device on the window). The
connector only ts one way so be
sure that the locking tab is on the
bottom.
Note: The device will power on
automatically when it detects your
vehicle has started. If you wish to
power up the device without starting
your vehicle, ensure the key is in the
run position and touch the screen
(CTS) or a button (CS).
Once the alcohol has dried
you’re ready to attach the
mount to the wind-
shield.
UNLOCKED
Once you’ve locked the mount to
the windshield, use the adjustment
knobs to ne tune the viewing angle
and height of the the CTS/CS device.
CS/CTS QUICK INSTALL INSTRUCTIONS Step 1: Locate the OBDII Port Step 2: Connect/Route the OBDII Cable Step 3: Position the Device Step 4:Connect the Mount and OBDII Cable Step 5: Position and Lock the Device on theWindshield
VERTICAL ADJ.
KNOB
This knob will allow you
to adjust the viewing
angle and height of the
device up or down.
LOCKED
You’ll notice that the mount has
a locking tab. This tab creates the
suction that will lock the mount
to the windshield. Make sure
the lock is in the “Unlocked”
position. Position the
mount where you’ve
cleaned the windshield,
press rmly, and push the tab to the
“Locked” position.
VARIABLE ANGLE ADJ
KNOB
This knob will allow you to
adjust the viewing angle of
the device in both horizontal
and vertical fashions. Use
it to ne tune your viewing
angle.
OBDII LOCATIONS

After you’ve locked the mount and the CS/CTS device is
in place on your windshield, sit back in your drivers seat
and make sure the viewing angle is as desired. Check
to make sure the device doesn’t create a blind spot that
may impair your view of the road/trac/pedestri-
ans from the drivers seat.
After positioning the device
and the mount, remove any
slack in the OBDII cable and
coil it behind the side panel
you removed earlier. Use the
supplied zip ties to secure the
coiled cable from moving or
falling down under the dash, or
interfering with pedal operation.
Replace all panels removed during
installation
For Operating Instructions and trouble shooting please refer to the User Guide found
in the folder packet that came with your CS or CTS package. For additional questions
not found in the User Guide you can call:
Edge Products Technical Support
Hours Mon-Friday
8:00 a.m. - 5:00 p.m. Mountain Standard Time
1-888-360-EDGE (3343)
Multiple accessories are available for
the CS/CTS device. Accessories
include EGT sensors, back-up
camera, and vehicle-specic
custom mounting solutions.
For more information and
pricing please visit
VIDEO IN PORT (CTS ONLY)
CS/CTS DEVICE DESCRIPTIONS
Step 6:Verify Position and Viewing Placement
ACCESSORIESPORT
*Note: Some states prohibit mounting devices
that may obstruct your view. Please check local
and state laws to ensure compliance.
For alternate mounting options visit
www.edgeproducts.com or www.arkon.com
CTS LAYOUT
CS LAYOUT
Up/Down Arrow Button1. - On the JUICE ATTITUDE these buttons are used to toggle the power level up/
down. On the EVOLUTION,INSIGHT and MILEAGE MAX these buttons may be used for future feature enhance-
ments. In the menus these buttons areused to toggle through the menu items and increase or decrease
values.
Menu Button2. - The menu button gives you access to the main menu.
Left Gauge3. - The left gauge is one of two analog style gauges. The displayed parameterfor all gauges
can be changed by pressing the enter button, choosing the desired gauge, and selecting a dierent parameter
from the drop down list.
Alert Indicator4. - The alert indicator light will illuminate (red) when an alert limit is exceeded. When this
light contains an “R,”it indicates that your Diesel Particulate Filter (DPF) equipped vehicle is performing a
regeneration cycle.
Power Level Indicator5. - The power level indicator represents the current powerlevel. 0 represents
stock.
Backdown Indicator6. - (Juice/Attitude only) The backdown indicator light will illuminate (yellow)
when the Juice module is decreasing power added by the device while exceedinga backdown limit. The light
will contain one of the following characters; E= EGT, S = Transmission Slip, C = Cold Engine.
Right Gauge7. - The right gauge is one of two analog style gauges.
Enter Button8. - The enter button when pressed from the main screen will allow you to change the gauge
parameters. Inthe menus it allows you to select the highlighted option.
Center Gauge9. - The center gauge is a bar style gauge.
Main Menu button1. - The main menu button gives you access to the main menu.
Left Gauge2. - The left gauge is one of three analog style gauges. The displayed parameterfor all gauges
can be changed by simply touching the gauge and choosing a dierent parameter from the drop downlist.
Power level up/down Arrows3. - On the JUICE ATTITUDE these buttons are used to toggle the power
level up/down. On the EVOLUTION,INSIGHT and MILEAGE MAX these buttons may be used for future feature
enhancements.
Alert Indicator4. - The alert indicator light will illuminate (red) when an alert limit is exceeded. When this
light contains an “R,”it indicates that your Diesel Particulate Filter (DPF) equipped vehicle is performing a
regeneration cycle.
Power Level Indicator5. - The power level indicator represents the current powerlevel. 0 represents
stock.
Backdown Indicator6. - (Juice/Attitude only) The backdown indicator light will illuminate (yellow)
when the Juice module is decreasing power added by the device while exceedinga backdown limit. The light
will contain one of the following characters; E = EGT,S = Transmission Slip, C = Cold Engine.
Right Gauge7. - The right gauge is one of three analog style gauges.
Lower Left Gauge8. - The Lower LeftG auge is one of two digital gauges.
Center Gauge9. - The Center gauge is one of three analog style gauges.
Lower Right Gauge10. -The Lower Right Gauge is the second of two digital gauges.
654
9
2
8
1
53
10
3
2
8
1
9
7
6
4
7
3
THE MAIN MENU CONSISTS
OF SIX OPTIONS:
Show alerts -• This item shows the
alert grid screen. *NOTE: This menu
only appears when there is an alert
active
Programming -• This allows you
to program the vehicle to one of the
pre-tuned levels included with the
Mileage Max or Evolution. This menu
item may not be present on certain
products.
Diagnostics -• Thisgives you the
ability to retrieve and clear trouble
codes, as well as other diagnostic
functions depending on vehicle.
Options -• This gives you access
to multiple device settings (i.e.
alert settings, sound duration,
backlight-autodim etc).
Help -• This is used to display product
information, vehicle information,
technical support tools, and contact
information.
MENU NAVIGATION BUTTONS
Both the CS and CTS devices provide you with the
following three buttons for navigating the menu
system:
Menu: The Menu button allows you to enter the main menu
(CS only). Once you are in the menu system you’lluse the Menu
button to return to the previous screen.
UP/Down Arrow: The Up/Down Arrow buttons will allow
you to toggle up or down through the menu options. Each
option will be highlighted as you toggle.
Enter: Pressing the Enter button will select the currently
highlighted option.
*Note: With the CTS device you can simply touch the option
you’dlike to select on the menu screen. As a touch screen
device it will automatically select the option you’ve touched
and advance you to the selected option screen.
CS/CTS MAIN MENU
CS/CTS ACCESSORIES