EdgeStar BWC121SS User manual

ii
V2.0-02112019
Beverage Cooler
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
To use the EdgeStar self-diagnostic tool, go to https://support.edgestar.com
BWC121SS

i
Important Safety Information
Improper handling can cause serious damage to the EdgeStar beverage cooler and / or injury
to the user. This beverage cooler is designed for domestic indoor use only. Do not use the
unit for industrial or commercial use. Any other use may invalidate the warranty. Please
review the ratings label located on the rear panel of the unit for electrical and other technical
data related to this unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire,
electric shock, or injury.
Electrical Safety
Do not exceed the power outlet ratings.
It is recommended the beverage cooler be connected on its own circuit.
The unit must be installed in accordance with state and local electrical codes.
A standard electrical supply (115 V, 60Hz), that is properly grounded in accordance with the
National Electrical Code and local codes and ordinances is required.
Use outlets that cannot be turned off by a switch or pull chain.
Always turn the unit off and unplug it from the outlet when cleaning.
Unplug the unit if it is not going to be used for an extended period of time.
Do not operate the unit with a power plug missing the ground plug, a damaged cord, or a loose
socket.
Be sure the beverage cooler is properly grounded.
Never plug or unplug the unit with wet hands.
Do not bypass, cut, or remove the grounding plug.
Do not use extension cords or power strips with this unit. You may need to contact your electrician if
it is necessary to use a longer cord or if you do not have a grounded outlet. Do not modify the power
cord’s length or share the outlet with other appliances.
Do not start or stop the unit by switching the circuit’s power on and off.
If the power cord is damaged, it must be replaced by the manufacturer or a qualified technician.
Never repair the unit while it is plugged in.
Immediately unplug the unit if it makes strange sounds, emits smells, or smoke comes out of it, and
contact customer service.
Do not remove any part of the casing unless you are instructed to do so by an authorized
technician.
You should never attempt to repair the unit yourself.
Contact customer service for service options if the unit needs service.

ii
Note: This owner’s manual is provided for reference use only. Specifications may change
without prior notice. Refer to the product label on the back of your beverage cooler for the
latest technical information.
General Safety
To prevent back and other types of injuries, use at least two people to move and install the
beverage cooler.
This appliance is not intended for use by persons, including children, with reduced physical,
sensory, or mental capabilities, unless they have been given supervision or instruction concerning
the use of the appliance by the person(s) responsible for their safety.
Install the beverage cooler in a well ventilated area where the ambient temperature is above 50° F
and below 95° F.
The temperature range for this cooler is optimized for beverage storage. Perishable food items may
require a different storage environment.
Do not place hot or warm items into the cooler before they cool down to room temperature.
This unit is designed to be installed indoors, and protected from rain, sleet, snow, and / or moisture.
This unit is not intended to be used by children.
Children should be supervised to ensure that they do not play with this product.
Never allow children to crawl inside the beverage cooler. If you are disposing of the unit, remove the
door.
Do not use this cooler near flammable gas or combustibles, such as gasoline, benzene, thinner, etc.
Do not place the unit near heat sources such as ovens, grills, or direct sunlight.
Only use in an upright position on a flat, level surface and provide proper ventilation.
Do not pinch or kink the power supply line between the unit and cabinet.
Do not leave any cleaning solutions in the unit.
Do not use solvent-based cleaning agents or abrasive solutions to clean the unit as they may
damage the interior and exterior.
Do not place any other appliances or allow anyone to sit on top of the unit.
Do not turn the unit upside down, on its side, or at an angle off level.
Do not move the unit without emptying the contents and securing the door in a closed position.
If your model of beverage cooler is equipped with a lock, take care to keep the keys away from
children.
Note: Flammable Refrigerant Used! When handling, moving, and using the refrigerator, make
sure to avoid either damaging the refrigerant tubing, or increasing the risk of a leak.

iii
Table of Contents
IMPORTANT SAFETY INFORMATION.................................................................................................................I
TABLE OF CONTENTS......................................................................................................................................III
FIRST TIME OPERATING INSTRUCTIONS.....................................................................................................................1
INTRODUCTION..................................................................................................................................................1
PARTS IDENTIFICATION....................................................................................................................................2
FRONT VIEW ..........................................................................................................................................................2
BACK VIEW ............................................................................................................................................................2
Internal Fan..........................................................................................................................................................3
INSTALLING THE BEVERAGE COOLER............................................................................................................3
UNPACKING THE BEVERAGE COOLER.......................................................................................................................3
TYPES OF INSTALLATION..........................................................................................................................................3
Free-standing Installation:.....................................................................................................................................3
INSTALLATION CLEARANCE REQUIREMENTS...............................................................................................................4
ELECTRICAL REQUIREMENTS ...................................................................................................................................5
Recommended Grounding Method.......................................................................................................................5
LEVELING THE BEVERAGE COOLER...........................................................................................................................6
REVERSING THE DOOR SWING .................................................................................................................................7
To Remove the Door: ...........................................................................................................................................7
To Install the Door................................................................................................................................................7
OPERATION........................................................................................................................................................8
INSTALLATION CHECK LIST BEFORE OPERATION ........................................................................................................8
ADJUSTING THE TEMPERATURE................................................................................................................................8
NORMAL SOUNDS ...................................................................................................................................................9
DEFROSTING..........................................................................................................................................................9
PREPARING THE BEVERAGE COOLER FOR STORAGE ..................................................................................................9
CLEANING AND MAINTENANCE .....................................................................................................................10
EXTERIOR CLEANING ............................................................................................................................................10
INTERIOR CLEANING..............................................................................................................................................10
TROUBLESHOOTING.......................................................................................................................................11
ERROR CODES.....................................................................................................................................................12
SPECIFICATIONS .............................................................................................................................................13
EDGESTAR LIMITED WARRANTY...................................................................................................................14

1
First Time Operating Instructions
Before use, make sure all packaging labels and materials are removed from the unit. Be sure
to keep track of all included parts and pieces before discarding packaging materials. It is
advised that you keep the original box and packaging materials in case you ever need to move
or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling components
time to settle from transit. The instruction manual should be read before use.
Introduction
Thank you for purchasing this EdgeStar beverage cooler. We hope that this purchase will be
the beginning of a lasting and rewarding relationship between you and EdgeStar. We will
provide the customer support and exemplary products necessary to nurture that relationship.
This manual contains important information regarding the proper installation, use, and
maintenance of your beverage cooler. Following this manual will ensure that your product will
work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport your beverage
cooler.
For Your Records:
Please write down the model number and serial number below for future reference.
Both numbers are located on the ratings label on the back of your unit and are needed
to obtain warranty service. You may also want to staple your receipt to this manual as it
is the proof of your purchase, and is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
For a more efficient experience, please do the following before contacting customer service:
If you received a damaged product, immediately contact the retailer or dealer that sold you
the product.
Read and follow this instruction manual carefully to help you install, use, and maintain
your beverage cooler.
Read the troubleshooting section of this manual as it will help you diagnose and solve
common issues.
Visit us on the web at http:/www.edgestar.com to register your product, download product
guides, and access additional troubleshooting resources and up-to-date information. You
can also find an interactive self-diagnostic tool at https://support.edgestar.com
If you need warranty service, our friendly customer service representatives are available
via email at [email protected].

2
Tip: Gather the model and serial number from the product label and write them down before
installing the beverage cooler.
Parts Identification
Front View
Back View
Note: The carbon filter
should be replaced
every 3-6 months
depending on the
unit’s exposure level
to odor. If the unit is
placed in the kitchen
regular replacement
every 3 months is
ideal.

3
Important: Do not remove any safety, warning, or product information labels from your
beverage cooler.
Warning: You may need to use two or more people to move and install the beverage cooler.
Failure to do so can result in back or other injury. Carefully remove the packaging materials.
Remove any shipping tape and glue from your beverage cooler before using. Do not use
sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or
glue. These products can damage the surface of your beverage cooler.
Internal Fan
This unit is equipped with an internal fan that maintains a consistent internal temperature.
Installing the Beverage cooler
The beverage cooler should be installed in accordance with local electrical code requirements.
The beverage cooler should also be placed in a location that is strong enough to support its
total weight, keeping in mind that it will weigh substantially more when fully loaded than when
empty. Before you plug the beverage cooler into a power supply, be sure to let it stand
upright for at least 24 hours to allow the compressor’s oils to settle.
Unpacking the Beverage Cooler
Types of Installation
This beverage cooler has been designed for free-standing installation only. There must be
adequate ventilation space around the top, back, and sides of the unit.
Free-standing Installation:
A free-standing installation will allow you to install the beverage cooler in almost any place
you desire. You must follow the stated instructions for electrical requirements, installation
clearance, and leveling the beverage cooler.
Tip: Gather the model
and serial number
from the product label
and write them down
before installing the
refrigerator.
Warning: DO NOT install the beverage cooler built-in or behind a closed cabinet door.
Tip: Gather the model and serial number from the product label and write them down before
installing the Beverage Cooler.

4
Important Notes:
Choose a location that has ambient temperatures above 50° F and below 95° F. Operation
outside these temperatures may result in lowered efficiency or cause other adverse
effects.
This unit MUST be installed indoors in an area protected from the elements, e.g. wind,
rain, water spray or drips.
The beverage cooler should not be located next to ovens, grills, or other high heat
sources.
Do not kink or pinch the power supply cord between the beverage cooler and the wall or
cabinet.
Installation Clearance Requirements
When installing the Beverage Cooler, follow the recommended spacing dimensions shown.
To ensure proper ventilation, allow at least 5” of clearance at the back, 3” at the top, and
3” at the sides.
The beverage cooler should be installed on a firm and level surface that will be able to
support the entire weight of a fully loaded unit. It is important for the beverage cooler to be
level in order to work properly. If needed, you can adjust the height of the beverage cooler
by rotating the feet. See the “Leveling the Beverage Cooler” section.
A standard electrical supply (115 VAC only, 60 Hz), properly grounded in accordance with
National Electrical Code and local codes and ordinances, is required.
Important Notes:
• Choose a location that has
ambient temperatures above
50°F and below 95°F.
Operation outside these
temperatures may result in
lowered efficiency or cause
other adverse effects.
• This unit MUST be installed
in an area protected from the
elements, e.g., wind, rain,
water spray or drips.
• The refrigerator should not
be located next to ovens,
grills or other high heat
sources.
•Do not kink or pinch the
power supply cord between
the refrigerator and wall or

5
ELECTRIC SHOCK HAZARD!
Plug into a grounded 3-prong outlet.
Never remove the grounding prong from the plug.
Never use an adapter to bypass the grounding prong.
DO NOT use an extension cord.
Failure to follow these instructions can result in fire, electrical shock, or death.
Electrical Requirements
Before you move your beverage cooler into its final location, it is important to make sure you
have the proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in accordance with the National
Electrical Code and local codes and ordinances, is required.
It is recommended that a separate circuit, serving only your beverage cooler, be provided. Use
outlets that cannot be turned off by a switch or pull chain.
The fuse (or circuit breaker) size should be 15 Amps.
Recommended Grounding Method
For your personal safety, this appliance must be grounded. It is equipped with a power
supply cord that has a 3-pronged grounding plug. To minimize possible shock hazard, the
cord must be plugged into a mating 3-pronged wall socket, and grounded in accordance
with the National Electrical Code and local codes and ordinances. If a mating wall socket
is not available, it is the personal responsibility of the customer to have a properly
grounded, 3-prong wall receptacle installed by a qualified electrician.

6
Important:
Once you are ready to install the beverage cooler directly on the floor, you must adjust
the feet to level the beverage cooler.
The beverage cooler only requires one large adjustable leveling foot and one small
leveling foot. If these are present then pieces are not missing.
The rear support of the beverage cooler will sit directly on the floor.
Leveling the Beverage Cooler
It is important for the beverage cooler to be leveled in order to work
properly. In order to level the beverage cooler please use the following
steps:
1. Turn the small leveling foot on the right side of the refrigerator
to the right until completely tightened.
2. Place a carpenter’s level on top of the product to see if the
beverage cooler is level from front to back and side to side.
3. Turn the large leveling foot on the left side of the refrigerator to
the right to lower that side of the refrigerator or to the left to raise
that side of the refrigerator.
If you find that the surface is not level, rotate the large foot until the beverage cooler becomes
level. You may need to make several adjustments to level it. We recommend using a carpenter’s
level to check that the unit is level.

7
Reversing the Door Swing
Tools needed: flathead screwdriver, Philips screwdriver
To Remove the Door:
1. Using a flathead screw driver carefully pry the top hinge cover off.
2. Using a Philips screwdriver, remove the screws and take off the top hinge. Keep the
parts together and set them aside.
3. Lift the door off the bottom hinge and set the door aside.
4. Remove the bottom hinge by removing the screws with a Philips head screwdriver.
To Install the Door
1. Using a flathead screwdriver, remove the decorative plugs or cover from the opposite
cabinet top corner and from the door. Set the plugs or cover aside.
2. Install the bottom hinge at the opposite side corner and fasten the screws.
3. Position the door on the bottom hinge.
4. Align the door on the bottom hinge and install the top hinge.
5. Push the decorative plugs or covers into the corresponding holes.
Important: Before you begin, unplug the beverage cooler.

8
Operation
Installation Check List Before Operation
1. Have all packing materials and tape been removed from the interior and exterior of the
beverage cooler?
2. Have the installation instructions been followed, including connecting the machine to
electricity, and has proper grounding been installed for the beverage cooler?
3. Has the machine been leveled?
4. Is the beverage cooler in a site where the ambient temperature is between 50° F and
95° F all year round?
5. Is there a clearance of at least 5” at the back, 3” at the top, and 3” at the sides for proper
air circulation?
Adjusting the Temperature
The beverage cooler has a temperature range from 38°F to 65°F and will display the current
temperature.
Allow at least 24 hours before storing your beverages to allow the temperature to acclimate.
Up Button : Press the button on the control panel to increase the temperature by 1
degree increments.
Down Button : Press the button on the control panel to lower the temperature by 1
degree increments.
Light Button : Press the button to turn the inner light on or off.
Power Button : Turns the unit on and off. ( press and hold this button for approximately 3
seconds)
The Celsius or Fahrenheit light will be lit depending on which temperature type is being
displayed. To switch between C and F. press and hold both buttons (▲/ ▼) simultaneously
for approximately 5 seconds.
Caution: If you powered off the unit, please wait at least 5 minutes before powering it back on.

9
Warning: Never attempt to remove frost with a sharp object!
Normal Sounds
Your new beverage cooler may make sounds that are not familiar to you. Most of the new
sounds are normal. Hard surfaces like the floor and walls can make the sounds seem louder
than they actually are. The following describes the kinds of sounds that might be new to you
and what may be making them.
Rattling noises may come from the flow of the refrigerant or the water line. Items stored on
top of the beverage cooler can also make noises.
The high efficiency compressor may make a pulsating or high pitched sound.
Water running from the evaporator to the water bin may make a splashing sound.
As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your
beverage cooler.
You may hear air being forced over the condenser by the condenser fan.
Defrosting
This beverage cooler does NOT have an automatic defrost feature. Therefore, in a colder
environment and settings, frost may build up frequently. Additionally, the more humid the
ambient conditions, the more frost may build up. Keep the door closed as much as possible
and avoid opening the door unnecessarily to minimize frost build up.
If frost is preventing the door from closing properly, you may need to power the unit off until the
frost melts. Use a soft absorbent towel to dry the unit.
Preparing the Beverage Cooler for Storage
If the beverage cooler will not be used for a long time, or is to be moved to another place, it will
be necessary to defrost the unit and dry the interior.
1. Disconnect the cooler from the power supply by removing the power plug from the wall
socket.
2. Leave the door open to allow for air circulation and to prevent mold, mildew, and
unpleasant smells.
IMPORTANT:
• Do not touch the power plug
when your hands are wet.
• Never unplug the unit by
pulling on the plug.
Caution: Store the unit out of the reach of children. If you have children, you may want to take
additional precautions such as removing the door to prevent a child from being trapped inside
the cooler!
Important:
Do not touch the power plug when your hands are wet.
Never unplug the unit by pulling on the cord.

10
Cleaning and Maintenance
Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life.
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such
as 2 tablespoons of baking soda to 1 quart of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water.
Wipe with a soft clean towel to prevent water spotting. If the door panel is stainless steel, it can
discolor when exposed to chlorine gas and moisture. Clean stainless steel with a cloth
dampened with a mild detergent and warm water solution. Never use an abrasive or caustic
cleaning agent.
Interior Cleaning
The beverage cooler’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and beverages.
6. Reconnect power to the unit.

11
Troubleshooting
Before Calling for Help
If the unit appears to be malfunctioning, read through the “Operation” section of this manual
first. If the problem persists, check the Troubleshooting Guide below and on the following page.
The problem may be something that can easily be solved or explained.
Symptoms
Possible Causes
Solutions
The beverage cooler turns on
and off frequently.
The room temperature is
higher than the recommended
ambient temperature.
Run the cooler at the
appropriate ambient
temperature (above 50° F and
below 95° F).
The door is being opened too
often.
Minimize the number of times
the door is opened.
The door is not completely
closed.
Make sure the door is
completely closed.
The door gasket is not sealing
properly.
Make sure the door gasket is
sealing properly.
The cooler does not have the
required ventilation.
Read and follow the
“Installation Clearance
Requirements” section.
The beverage cooler does not
turn on.
There is a power failure.
Ensure that the cooler is
plugged in and the power
outlet has power.
The cooler is not plugged in.
Plug the unit in to a power
outlet that has sufficient
amperage.
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in
your fuse box or reset the
breaker.
The beverage cooler will not
reach the desired
temperature.
The cooler is placed too close
to a heat source.
Keep the cooler away from
direct sunlight or other heat
sources.
The cooler does not the
required ventilation.
Read and follow the
“Installation Clearance
Requirements” section.
The door is opened too
frequently or for a long period
of time.
Close the door tightly and do
not open the door too
frequently or for a long period
of time.
The beverage cooler is
making strange noises.
Certain sounds are normal.
Read the “Normal Sounds”
section.
The unit is not level or is
touching another appliance.
Check to make sure that the
cooler is level, and that it is
not in contact with another
appliance or piece of furniture.

12
Symptoms
Possible Causes
Solutions
The body of the beverage
cooler is electrified.
The unit is not grounded
properly.
Contact your local electrician
to test your electrical
grounding system.
Frost is forming in the
beverage cooler.
The environment is humid.
Manual defrosting is required;
unplug the unit to allow the
frost to melt. If frost builds up
frequently, you can move the
unit to a location with a
warmer temperature,
minimize the number of times
you open the door, or check
the door gasket for a good
seal.
The ambient temperature is
too low.
The door gasket is not
installed properly.
The door is being opened too
frequently.
The door will not shut
properly.
The cooler is not level.
Make sure the cooler is on a
level surface.
The door gasket is dirty.
Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is
correctly installed.
The shelves are incorrectly
installed.
Make sure the shelves are
correctly installed.
Error Codes
Error Code
Meaning
Possible Causes
EL
The temperature sensor is
experiencing an “Open
Circuit.”
The temperature sensor is
unplugged. The temperature
sensor is faulty.
EH
The temperature sensor is
experiencing a “Short.”
The temperature sensor is
faulty.

13
Specifications
Description of product
Freestanding Beverage Cooler
Model
BWC121SS
Voltage / Frequency
AC 115V~60Hz
Amperage
1.1 A
Input Power
80 W
Color
Black Cabinet; Stainless Steel Door
Storage Capacity
105 Cans*
Temperature Range
38° F - 65° F
Dimensions
(Height x Width x Depth )
32 3/8” x 18 7/8”x 18 1/4”
Net Weight
64 lbs
Note: Technical data and performance information are provided for reference only.
Specifications are subject to change. Check the rating label on the beverage cooler for the
most accurate information.
*Note on Beverage Storage Capacity: The beverage cooler can store 105 standard 12 oz.
cans.

14
EdgeStar Limited Warranty
One (1) Year Parts & Ninety (90) Days Labor
This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions set forth as
follows:
WHAT IS COVERED:
LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at an
authorized EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts, or exchange
the defective product with a new, refurbished, or remanufactured product. If a product is replaced, it will carry the remaining
warranty of the original product. After the ninety (90) day period, EdgeStar will no longer be responsible for labor charges
incurred. All defective products and parts covered by this warranty will be repaired or replaced on a mail-in basis to an EdgeStar
authorized repair facility.
PARTS: For a period of ONE (1) YEAR from the date of original purchase, EdgeStar will supply new, rebuilt, or refurbished parts free
of charge. EdgeStar may request a defective part be returned in exchange for the replacement part. All replacement parts or
products will be new, remanufactured, or refurbished. All products and parts replaced by EdgeStar under warranty service
become the property of EdgeStar.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during operation of
the product under normal service, maintenance, and usage conditions. This warranty applies to the purchase and use of this
product in residential settings within the contiguous United States of America.
WHAT IS NOT COVERED:
The following limitations apply to the coverage of this warranty. This warranty does not cover:
Labor charges for installation, setup or training to use the product.
Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse, including abnormal service, handling, or usage.
Cosmetic damage such as scratches and dents.
Normal wear and tear on parts or replacement of parts designed to be replaced, e.g. filters, cartridges, batteries.
Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
Damages or operating problems resulting from misuse, abuse, operation outside environmental specifications, uses contrary to
instructions provided in the owner’s manual, accidents, acts of God, vermin, fire, flood, improper installation, unauthorized
service, maintenance negligence, unauthorized installation or modification, or rental or commercial use.
Labor, service transportation, and shipping charges incurred 91 days or more after the date of original purchase.
The use of EdgeStar products in commercial or rental settings.
Optional accessories, attachments, and appearance items.
Products that have been modified to perform outside of specifications without the prior written permission of
EdgeStar.
Products lost in shipment, or theft.
Products sold AS IS or from an unauthorized reseller.
Products that have had their serial numbers removed or defaced. Products with serial numbers that have been invalidated.
Damage to personal property from use of product.
Replacement of repair of household fuses, circuit breakers, wiring, or plumbing.
OBTAINING WARRANTY SERVICE:
If you believe your product is defective, contact EdgeStar Customer Support for troubleshooting assistance and warranty service at
www.edgestar.com or 1-866-319-5473. Before contacting EdgeStar, have your serial number and proof of purchase available. Once an
EdgeStar authorized representative has confirmed that your product is defective and eligible for warranty service, the product must be
returned to an EdgeStar repair facility. The purchaser is solely responsible for prepaying all shipping related costs to and from the repair
facility. EdgeStar is not responsible for damage resulting from shipper mishandling or improper packaging. Do not return a defective
product to the place of purchase. Products received without a return authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION
TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR
ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. IN NO EVENT AND UNDER NO CIRCUMSTANCE OF ANY TYPE OR KIND
SHALL THE SELLER, MANUFACTURER AND/OR DISTRIBUTOR BE LIABLE FOR ANY REASON, UNDER ANY THEORY, FOR MORE THAN THE BASIC COST OF
THE PRODUCT TO THE PURCHASER OR END USER. SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY
FROM STATE TO STATE.