Edimax AR-7287WnA User manual

AR-7287WnA
User Manual
04-2017 / v1.0

Contents
1. PRODUCT INTRODUCTION .....................................................................................................................4
1.1. PACKAGE CONTENTS............................................................................................................................4
1.2. SYSTEM REQUIREMENTS.......................................................................................................................4
1.3. SAFETY PRECAUTIONS ..........................................................................................................................4
1.4. LED STATUS &BUTTON DEFINITIONS .....................................................................................................5
1.5. FEATURES..........................................................................................................................................7
2. HARDWARE INSTALLATION..................................................................................................................10
3. IP ADDRESS SETTING ............................................................................................................................16
3.1. WINDOWS 10/ 8..............................................................................................................................16
3.2. WINDOWS 7....................................................................................................................................19
3.3. WINDOWS VISTA ..............................................................................................................................20
3.4. WINDOWS XP..................................................................................................................................21
4. WEB CONFIGURATION .........................................................................................................................23
4.1 ACCESS THE ROUTER.............................................................................................................................23
4.1.1. Status....................................................................................................................................23
4.1.2. Wizard..................................................................................................................................27
4.1.3. Setup ....................................................................................................................................31
4.1.4. LAN......................................................................................................................................37
4.1.5. WLAN...................................................................................................................................44
4.2. ADVANCED ......................................................................................................................................52
4.2.1. Route....................................................................................................................................52
4.2.2. NAT......................................................................................................................................55
4.2.3. QoS ......................................................................................................................................60
4.2.4. CWMP..................................................................................................................................62
4.2.5. Port Mapping.......................................................................................................................64
4.2.6. Others ..................................................................................................................................67
4.3. SERVICE ..........................................................................................................................................70
4.3.1. IGMP ...................................................................................................................................70
4.3.2. UPnP....................................................................................................................................70
4.3.3. SNMP...................................................................................................................................71
4.3.4. DNS......................................................................................................................................72
4.3.5. DDNS...................................................................................................................................73
4.3.6. FTP Server...........................................................................................................................74
4.4. FIREWALL ........................................................................................................................................74
4.4.1. MAC Filter...........................................................................................................................74
4.4.2. IP/Port Filter.......................................................................................................................75

4.4.3. URL Filter............................................................................................................................76
4.4.4. ACL......................................................................................................................................76
4.4.5. DoS ......................................................................................................................................80
4.5. MAINTENANCE .................................................................................................................................82
4.5.1. Update..................................................................................................................................82
4.5.2. Password..............................................................................................................................83
4.5.3. Reboot..................................................................................................................................84
4.5.4. Time .....................................................................................................................................85
4.5.5. Log.......................................................................................................................................85
4.5.6. Diagnostics..........................................................................................................................86
5. TROUBLE SHOOTING ............................................................................................................................87
Note: The images/screenshots used in this manual are for reference only –
actual screens may vary according to firmware version. The contents of this
manual are based on the most recent firmware version at the time of writing.

User Manual
1. Product Introduction
1.1. Package Contents
Before you start using this product, please check if there is anything missing in
the package and contact your dealer to claim the missing item(s):
ADSL2+ router (AR-7287WnA)
12V power adapter
1 meter RJ-45 Ethernet cable
1 meter RJ-11 telephone line x 2
Quick installation guide
CD containing setup wizard, user manual & multi-language QIG
Splitter
1.2. System Requirements
Recommended system requirements are as follows.
A 10/100 base-T Ethernet card installed in your PC.
A hub or Switch (connected to several PCs through one of the Ethernet
interfaces on the device).
Operating system: Windows 98 SE, Windows 2000, Windows ME,
Windows XP, Windows 7, Windows 8, Windows 10.
Internet Explorer V5.0 or higher, Netscape V4.0 or higher or Firefox 1.5
or higher.
1.3. Safety Precautions
Follow the following instructions to prevent the device from risks and
damage caused by fire or electric power:
Use volume labels to mark the type of power.
Use the power adapter included within the package contents.
Pay attention to the power load of the outlet or prolonged lines. An
overburdened power outlet or damaged lines and plugs may cause an
electric shock or fire. Check the power cords regularly. If you find any
damage, replace it at once.
Proper space left for heat dissipation is necessary to avoid damage
caused by overheating to the device. The long and thin holes on the
device are designed for heat dissipation to ensure that the device works
normally. Do not cover these heat dissipation holes.

User Manual
Do not put this device close to heat sources or high temperatures. Keep
the device out of direct sunshine.
Do not put this device close to a place where it is damp or wet. Do not
spill any fluid on this device.
Do not connect this device to any PCs or electronic products, other than
those which you are instructed or recommended to do so in the
product’s documentation, by our customer engineers or by your
broadband provider –connecting to incorrect devices may cause a fire
risk.
Place this device on a stable surface.
1.4. LED Status & Button Definitions
Front Panel
LED Status
Front Panel:

User Manual
LED
Color
Status
Description
Power
Green
On
ADSL2+ router is on.
Off
ADSL2+ router is off.
ADSL
Green
On
ADSL line is synchronized and ready to use.
Flashing
ADSL line not synchronized.
Internet
Green
On
Internet connected in router mode
Flashing
Internet not connected in router mode
Off
Device in bridged mode.
LAN1–4
Green
On
LAN port connected.
Off
LAN port not connected.
WLAN
Green
On
Successful WLAN connection.
Off
WLAN connection failed.
WPS
Green
Off
WPS is disabled.
Flashing
WPS is enabled and waiting for client to negotiate.
Note i. If the ADSL LED is off, please check your Internet connection.
Refer to A. Hardware Installation for more information
about how to connect the router correctly. If all connections
are correct, please contact your ISP to check if there is a
problem with your Internet service.

User Manual
Rear Panel:
Item
Description
Power On/Off
Button
Switches the router on or off.
Power
Power port for included 12V power adapter.
Wireless / WPS
Button
*Hold for less than 5 seconds to enable wireless signal.
*Hold for more than 5 seconds to activate WPS function.
LAN 1–4
RJ-45 Ethernet ports 1–4.
Reset Button
Hold for less than 3 seconds to reset the device to factory default
settings.
Line
RJ-11 port for standard telephone line.
1.5. Features
The device supports the following features:
Various line modes (line auto-negotiation)
External PPPoE dial-up access
Internal PPPoE/PPPoA dial-up access
1483B/1483R/MER access
Multiple PVCs (eight at most)

User Manual
A single PVC with multiple sessions
Multiple PVCs with multiple sessions
Auto PVC
DHCP server
IPv4/IPv6
NAT/NAPT
ALG
TR-069
SNMP
Static route
Firmware upgrading through Web, TFTP, or FTP
Resetting to the factory defaults through Reset button or Web
DNS relay
Virtual server
Two-level passwords and usernames
Web interface
Telnet CLI
System status display
PPP session PAP/CHAP
IP/Port filter
Remote access control
Line connection status test
Remote management (Telnet; HTTP )
Backup and restoration of configuration file

User Manual
IP quality of service (QoS)
Universal plug and play (UPnP)
WLAN with high-speed data transmission rate, compatible with IEEE
802.11b/g/n, 2.4 GHz compliant equipment

User Manual
2. Hardware Installation
1. Connect the ADSL line.
Connect the line port of the router of the device to the modem interface of a
splitter using a telephone cable. Connect a telephone to the Phone interface
of the splitter using a telephone cable. Connect the Line interface of the
splitter to your existing, incoming line.
The splitter has three interfaces:
Line: Connect to a wall phone jack (RJ-11 jack).
Modem: Connect to the ADSL jack of the device.
Phone: Connect to a telephone set.
2. Connect the router to your LAN network.
Connect the LAN interface of the router to your PC, hub or switch using an
Ethernet cable.
Note:
Use twisted-pair Ethernet cables to connect the router to a hub or switch.
3. Connect the power adapter to the router.
Plug one end of the power adapter into a wall outlet and connect the other
end to the 12V interface of the device.

User Manual
The following diagrams show how to correctly connect the router, PC, splitter
and the telephone sets under two different configurations:
Configuration 1
0shows the correct connection of the router, PC, splitter and the telephone
sets, with no telephone set placed before the splitter.
Figure 1 –Connection diagram
(Without connecting telephone sets before the splitter)
Configuration 2
0shows the correct connection when a telephone set is installed before the
splitter.

User Manual
Figure 2 - Connection diagram
(Connecting a telephone set before the splitter)
Note:
When Configuration 2 is used, the filter must be installed close to the
telephone cable. Do not use the splitter to replace the filter.
Installing a telephone directly before the splitter may lead to failure of
connection between the device and the central office, or failure of Internet
access, or slow connection speed. If you really need to add a telephone set
before the splitter, you must add a micro filter before a telephone set. Do not
connect several telephones before the splitter or connect several telephones
with the micro filter.
4. Check the ADSL LED status.
Please check the ADSL LED on the front panel. This light indicates the status of
your ADSL broadband through your telephone line. If the light is on, you can
continue setup. However if the light is flashing, there is no broadband line
detected. Please call your Internet Service Provider (ISP) and inform them
about the flashing ADSL light to resolve the issue.
5. Firewall settings.
Please turn off all personal firewalls before you continue the setup –firewalls
can block communication between your PC and router.

User Manual
Note: You must use the power adapter included in the package with the
router, do NOT attempt to use a third-party power adapter.
6. PC LAN IP configuration.
Configure your PC’s LAN settings to automatically obtain an IP address from
the router by following the steps below:
1. Click “Start” and then select “Control Panel”.
2. Click “Switch to Classic View” in the top left to show additional setting
icons.

User Manual
3. Locate the “Network Connections” icon and double-click to open network
connection settings.
4. Select the “Local Area Connection” icon and right-click it to open the sub-
menu, then select “Properties”.
5. Select “Internet Protocol (TCP/IP)” and then click “Properties”

User Manual
6. Ensure that “Obtain an IP address automatically” and “Obtain DNS
server address automatically” are selected and then press “OK”.

User Manual
3. IP Address Setting
To use the router to access the Internet, the PCs in the network must have an
Ethernet adapter installed and be connected to the router either directly or
through a hub or switch. The TCP/IP protocol of each PC must be installed and
the IP Address of each PC has to be set in the same subnet as the router.
The router’s default IP Address is 192.168.2.1 and the subnet mask is
255.255.255.0. PCs can be configured to obtain IP Address automatically
through the DHCP Server of the router or a fixed IP Address in order to be in
the same subnet as the router. By default, the DHCP Server of the router is
enabled and will dispatch IP Address to PC from 192.168.2.100 to
192.168.2.200. It is strongly recommended to set obtaining IP address
automatically.
This section shows you how to configure your PC so that it can obtain an IP
address automatically for either Windows 95/98/Me, 2000 or NT operating
systems. For other operating systems (Macintosh, Sun, etc.), please follow the
manual of the operating system. The following is a step-by-step illustration of
how to configure your PC to obtain an IP address automatically for Windows
10, Windows 8, Windows 7, Windows Vista and Windows XP.
3.1. Windows 10/ 8
1. From the Windows 10/ 8 Start screen, you need to switch to desktop mode.
Click the Desktop icon in the bottom left of the screen.

User Manual
2. Click the Network icon and then select Open Network and Sharing Center
to open the Network and Sharing Center window.
3. Click Ethernet to open the Ethernet Status window, and then select
Properties. The Local Area Connection window will appear.

User Manual
4. Check your list of Network Components. Select Internet Protocol Version 4
(TCP/IPv4) and click the Properties button.
5. In the Internet Protocol Version 4 (TCP/IPv4) Properties window, select
Obtain an IP address automatically and Obtain DNS server address
automatically as shown on the following screen.

User Manual
6. Click OK (shown above) to confirm the setting. Your PC will now obtain an IP
address automatically from your router’s DHCP server.
Note: Please make sure that the router’s DHCP server is the only DHCP server
available on your LAN.
3.2. Windows 7
1. Click the Start button and select Control Panel. Double click Network and
Internet and click Network and Sharing Center, the Network and Sharing
Center window will appear.
2. Click Change adapter settings and right click on the Local Area Connection
icon and select Properties. The Local Area Connection window will appear.
3. Check your list of Network Components. You should see Internet Protocol
Version 4 (TCP/IPv4) on your list. Select it and click the Properties button.

User Manual
4. In the Internet Protocol Version 4 (TCP/IPv4) Properties window, select
Obtain an IP address automatically and Obtain DNS server address
automatically as shown on the following screen.
5. Click OK to confirm the setting. Your PC will now obtain an IP address
automatically from your router’s DHCP server.
Note: Please make sure that the router’s DHCP server is the only DHCP server
available on your LAN.
3.3. Windows Vista
1. Click the Start button and select Settings and then select Control Panel.
Double click Network and Sharing Center, the Network and Sharing Center
window will appear.
2. Click Manage network connections and right click on the Local Area
Connection icon and select Properties. The Local Area Connection window
will appear.