Edimax BR-6675nD User manual

BR-6675nD
Quick Installation Guide
11-2012 / v1.1

1
COPYRIGHT
Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission from Edimax Technology Co., Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability, or fitness for any particular purpose. Any software described in this
manual is sold or licensed as is. Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right
to revise this publication and to make changes from time to time in the contents hereof
without the obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly different from
those shown in this QIG. For more information about this product, please refer to the
user manual on the CD-ROM. The software and specifications are subject to change
without notice. Please visit our website www.edimax.com for updates. All brand and
product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.
Notice According to GNU General Public License Version 2
This product includes software that is subject to the GNU General Public License version
2. The program is free software and distributed without any warranty of the author. We
offer, valid for at least three years, to give you, for a charge no more than the costs of
physically performing source distribution, a complete machine-readable copy of the
corresponding source code.
The GNU GPL and GNU LGPL software codes used in Edimax products are distributed
without any warranty and are subject to the copyrights of their respective authors. The
firmware files for this product can be found under the “Download” page at the Edimax
website (www.edimax.com).

2
Package Contents
Installation
1. Screw in the three included 3dBi
antennas to the back of the router, and
use an Ethernet cable to connect the
router’s WAN port to your modem’s
LAN port.
2. Use an Ethernet cable to
connect any LAN port on the
router to the Ethernet port on
your computer.
BR-6675nD
QIG
x2
Setup Wizard CD
Power Adapter
Ethernet Cable
3dBi Antenna x3
3.Plug the included power adapter
into the router’s 12v Power jack
and the other end into an electrical
socket, and push the ON/OFF
button on the front of the router to
switch on the router.

3
5.Insert the setup wizard CD into a CD-ROM
drive on your computer. When the wizard
begins, select your language.
4.Ensure that the Power LED, WAN LED and corresponding LAN LED on the
router are lit. If not, the router is not properly connected.
Power
LAN 1 - 4
WAN
Note: If the setup wizard doesn’t run
automatically, please browse your
CD drive and double click the
“Ezmax.exe” file to start the wizard.
6.The setup wizard will guide you through
the installation process. Click “Next” to
continue.
7.Click “Next” to continue.

4
8.Check that all cables are properly
connected and check the box labeled
“YES, I have connected the cables
correctly”before clicking “Next”.
9.Select your product type –in this case
“BR-6675nD”.
10.Enter the default password 1234 in
the field labeled “Current Password”
and then if you wish to change this
password, enter a new password in the
fields marked “New Password” and
“Confirm New Password”. Click
“Apply” and then “Ok”.
Note: This is the password to login to your router to configure the settings –not
the password to connect to the router’s Wi-Fi network(s). If you change this
password, please make a note of the new password.
If you forget, you can reset the password back to its default value of 1234 by
resetting the router back to factory defaults, see Troubleshooting.

5
11.Select your Internet connection type
and click “Next”. If you are a dynamic IP
user, then select “Cable Modem”. For
most users, “Cable Modem” is the
correct setting. If you are unsure, please
contact your Internet Service Provider
(ISP).
12. If you received a host name and MAC
address from your ISP, enter them here
and click “Apply”. If you are sure the
MAC address is the same as your
computer, you can click “Clone”to
clone your computer’s MAC address
and then click “Apply”to continue.
13.Please wait while the router connects
to the Internet.

6
14.When the router is connected your default web browser will open. Close the
browser, and you will see the following screen. Please do not select Exit. You still
need to configure the ESSID and Wireless Security –please select “ESSID”from
the top menu next.
15.Please enter separate ESSIDs for the
router’s 2.4GHz mode and 5GHz mode.
An ESSID is a name to identify the
wireless router. Later, when the router
is fully operational, you will need to
select this ESSID from your available
Wi-Fi networks to connect to the
wireless router. Click “Apply”.
16.Please wait while the router is setting
its new ESSID. When it is finished, click
“Complete!” and then click “Next” to
continue.

7
17.To configure your router’s wireless
security, check the box labeled “Enable
WPA Pre-Share Key”. Then enter a
password for each of the router’s
2.4GHz and 5GHz networks. This
password will be required when you
connect to the router wirelessly. Click
“Apply” to save the settings.
18.Please wait for the router to save the
new passwords. When it is finished,
click “Complete!” and then click “EXIT”
in the top right corner to exit the setup
wizard.
19. You can now open a web browser to
access the internet and check your
router’s connection. Then, to connect to
the BR-6675nD’s wireless networks, you
need to unplug the Ethernet cable
connecting the router and your
computer.
Windows
Click the network icon ( , or ) in
the system tray and select “Connect to a
network”.
Mac
View available Wi-Fi networks by clicking
the icon along the top right of your
screen.

8
20. Windows
Search for the ESSID you named your
Wi-Fi network and click it and then click
“Connect”. If you set a password for your
network, you will then be prompted to
enter it.
Mac
Click on the ESSID of your network.
If you set a password for your
network, you will then be prompted
to enter it.
21. After correctly entering your
password, you will be successfully
connected to your Wi-Fi network.
Alternatively, if your wireless device supports WPS, you can use the WPS
button (see next section).

9
If your wireless device supports WPS (Wi-Fi
Protected Setup) then you can use this method to
connect to the BR-6675nD’s Wi-Fi networks.
For Mac/Linux users –or those who can’t run the CD, you can setup the router
manually using the web based configuration interface.
WPS Setup
Web Based Configuration Interface
1.Press the WPS/Reset button on the router
once to activate WPS for 2.4GHz Wi-Fi, or press
twice (within 5 seconds) to activate WPS for
5GHz Wi-Fi.
2.Within two minutes, press and hold the WPS
button on the wireless device/client to activate
its WPS.
Note: Please check the instructions for your
wireless device for how long you need to hold
down its WPS button to activate WPS.
3.The devices will establish a connection. Repeat
for additional wireless devices.
1.Enter http://192.168.2.1 into the URL of a
web browser and enter the username
admin and password 1234.
2.Select “General Setup”from the top
menu and “WAN”from the submenu.
Choose your connection type –for
most users it is “Dynamic IP”. If you are
unsure, please contact your Internet
Service Provider (ISP). Click “Apply” and
then “CONTINUE”.