Edimax GS-5208P User manual

ES-5208P
User Manual
10-2015 / v1.0
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Edimax
GS-5208PLG o cerca il tuo prodotto tra le migliori offerte di Switch

Table of Contents
Chapter 1 Product Introduction.................................................................................................................................. 3
1.1 Product Overview .......................................................................................................................................... 3
1.2 Features ......................................................................................................................................................... 3
1.3 Hardware Description .................................................................................................................................... 3
1.3.1 Front Panel.......................................................................................................................................... 3
1.3.2 Rear Panel ........................................................................................................................................... 5
1.4 Package Contents Preparation Before Installation......................................................................................... 5
1.4.1 Package Contents................................................................................................................................ 5
1.4.2 Optional Accessories and Tools........................................................................................................... 5
1.4.3 Choosing the Installation Location...................................................................................................... 6
1.4.3.1 Installing the ES-5208P on the Work Platform................................................................................. 6
1.4.3.2 Installing the ES-5208P on a Rack .................................................................................................... 6
1.5 Electrical Setup .............................................................................................................................................. 6
1.5.1 Setting Up the Power Interface........................................................................................................... 6
1.5.2 Setting Up the Ethernet Interfaces ..................................................................................................... 6
1.6 Device Startup................................................................................................................................................ 6
1.6.1 Check Before Power-On ...................................................................................................................... 6
1.6.2 Powering On the Device...................................................................................................................... 7
1.7 Device Upgrade.............................................................................................................................................. 7
Chapter 2 Web Configuration and Management....................................................................................................... 8
2.1 Preparation Before Login ............................................................................................................................... 8
2.2 Logging In to the Switch................................................................................................................................. 9
2.3 System Management ................................................................................................................................... 10
2.3.1 Authentication Configuration ........................................................................................................... 10
2.3.2 System IP Configuration.....................................................................................................................11
2.3.3 System Status.....................................................................................................................................11
2.3.4 Loading Default Settings ....................................................................................................................11
2.3.5 Firmware Update .............................................................................................................................. 12
2.3.6 Reboot the Device............................................................................................................................. 12
2.4 POE............................................................................................................................................................... 12
2.4.1 PoE Status ......................................................................................................................................... 13
2.4.2 PoE Setting ........................................................................................................................................ 13
2.4.3 PoE Power Delay ............................................................................................................................... 13
2.4.4 PoE Scheduling.................................................................................................................................. 14
2.4.5 NTP Setting........................................................................................................................................ 14
2.5 Port Management........................................................................................................................................ 15
2.5.1 Port Configuration............................................................................................................................. 15
2.5.2 Port Mirroring ................................................................................................................................... 16
2.5.3 Bandwidth Control............................................................................................................................ 16
2.5.4 Broadcast Storm Control................................................................................................................... 17
2.6 VLAN Setting ................................................................................................................................................ 17

2.6.1 VLAN Mode............................................................................................................................................... 18
2.6.1.1 VLAN Based on Port............................................................................................................................... 18
2.6.2 VLAN Member .......................................................................................................................................... 18
2.6.2.1 VLAN Based on Port............................................................................................................................... 18
2.6.2.2 VLAN Based on Tag ................................................................................................................................ 19
2.6.3 Multi to 1 Setting Configuration ............................................................................................................... 20
2.7 Per Port Counter .......................................................................................................................................... 21
2.8 QoS Configuration........................................................................................................................................ 22
2.8.1 Priority Mode............................................................................................................................................ 22
2.8.2 Class of Service Configuration - 1.............................................................................................................. 23
2.8.3 Class of Service Configuration - 2.............................................................................................................. 23
2.9 Security ........................................................................................................................................................ 25
2.9.1 MAC Address Binding................................................................................................................................ 25
2.9.2 TCP/UDP Filter .......................................................................................................................................... 26
2.10 Spanning Tree ............................................................................................................................................ 27
2.10.1 STP Bridge Settings ................................................................................................................................. 27
2.10.2 STP Port Settings..................................................................................................................................... 28
2.10.3 Loopback Detection:............................................................................................................................... 29
2.11 Trunking ..................................................................................................................................................... 30
2.12 DHCP Relay Agent ...................................................................................................................................... 32
2.12.1 DHCP Relay Agent ................................................................................................................................... 32
2.12.2 Relay Server ............................................................................................................................................ 32
2.12.3 VLAN MAP Relay Agent........................................................................................................................... 33
2.13 Configuration Backup and Recovery .......................................................................................................... 33
2.14 Miscellaneous Configuration ..................................................................................................................... 34
2.15 SNMP Settings............................................................................................................................................ 35
2.16 Logout........................................................................................................................................................ 36
Chapter 3 Troubleshooting....................................................................................................................................... 37
Chapter 4 Glossary .................................................................................................................................................... 38
Federal Communication Commission Interference Statement................................................................................. 41

Chapter 1 Product Introduction
Thank you for purchasing an Edimax PoE Web Smart Ethernet Switch. Before you install and use the product,
please read this manual carefully to make the best use of the product’s functions.
1.1 Product Overview
The Edimax ES-5208P is a web-smart switch with 8 Fast Ethernet PoE+ ports and 2 Gigabit Combo ports.
Designed for small or medium network environments to strengthen the network connection, its standard 13-inch
rack-mount brackets allow for integration with the most widely used mounting systems on the market.
1.2 Features
 Supports 8 10/100Mbps Fast Ethernet PoE+ ports and 2 10/100/1000Mbps combo ports
 Support IEEE 802.3af/at PoE compliant to simplify deployment and installation
 Support PoE up to 30W per port With 160W total power budget
 Automatically detects power devices(PD) and power consumption levels
 IEEE 802.1Q VLAN allows network segmentation to enhance performance and security
 Switch capacity:2.8Gbps, Forwarding rate:35.7Mbps
 Support IGMP Snooping V1 / V2
 Support 4K MAC address table
 13-inch rack-mountable metal case
1.3 Hardware Description
1.3.1 Front Panel
Front Panel

The following table describes the interface of the ES-5208P.
Interface/Button
Description
1~8
8 x RJ-45 Ethernet interfaces, 10 M/100 M self-adaptive.
9, 10
Two groups of fiber-copper combo ports. The copper ports are 10
M/100 M/1000 M self-adaptive Ethernet ports and the fiber ports are
SFP optical module ports. If the combo ports are preferred to serve as
fiber ports, that is, if the ports connect to a fiber port, the copper port is
disabled.
Reset
Keep the device powered on and push a paper clip into the hole. Press
down the button for about 5 seconds. The system restores the factory
default settings.
The following table describes the twenty-seven LED indicators of the PF108C.
Power: Green LED
-Off: power off or fail
-On: power on
10/100Mbps port LED: 2 LEDs per port, on RJ45 jack
Link/Activity: Amber LED
-Off: port disconnected or link fail
-On: port connected
-Blinking: sending or receiving data
PoE status: Green LED
-Off: PoE power off
-On: PoE power on
10/100/1000Mbps copper port: 2 LEDs, on RJ45 jack
-Off: port disconnected or link fail
-Green on: 1000Mbps connected
-Amber on: 10/100Mbps connected
-Blinking : sending or receiving data
-
SFP: Green LED
-Off: port disconnected or link fail
-on: 1000FX connected
-Blinking : sending or receiving data


1.3.2 Rear Panel
The rear panel of the switch features the AC power connector:
Rear Panel
Interface
Description
100-240VAC 50/60Hz
The power interface.
The power input is 100 V ~ 240 V AC, 50 Hz ~
60Hz.
AC Power Connector:
Power is supplied through an external AC power adapter. Supports AC 100 –240V, 50-60Hz
1.4 Package Contents Preparation Before Installation
1.4.1 Package Contents
Before you start using this product, please check if there is anything missing in the package, and contact your
dealer to claim the missing item(s):
 ES-5208P POE Web Smart Switch
 Quick Installation Guide
 CD
 Power Cord
 Rack-Mount Kit
1.4.2 Optional Accessories and Tools
 Screwdriver
 ESD straps
 Ethernet crimping pliers, 8P8C crystal heads
 Ethernet (either crossover or straight through) cable

1.4.3 Choosing the Installation Location
The ES-5208P can be installed in either of the following ways as required:
 On the work platform
 on a rack
1.4.3.1 Installing the ES-5208P on the Work Platform
The common way is to install the ES-5208P on a clean work platform. Pay attention to the following precautions:
 Ensure that the work platform is flat and stable.
 Ensure good ventilation of air ports on both sides of the device.
 Do not put heavy objects on the device.
1.4.3.2 Installing the ES-5208P on a Rack
Before installing the ES-5208P on a rack, you need to install the provided L- Clamps on both sides of the ES-5208P
1.5 Electrical Setup
1.5.1 Setting Up the Power Interface
After placing the ES-5208P to a flat and stable surface, insert the supplied power cable to the power socket, and
connect the other end of the cable to the power interface of ES-5208P.
1.5.2 Setting Up the Ethernet Interfaces
The ES-5208P provides twenty-four auto-MDI/MDI-X Ethernet service interfaces of standard RJ45 connectors. You
can use either the crossover or straight through cable to connect an interface.
Note: To ensure good quality of the data signal, the length of the network cable connected to the Ethernet
interface should be shorter than 100m.
1.6 Device Startup
1.6.1 Check Before Power-On
Before powering on the device, check the following:
 Whether the voltage of the power supply is consistent with the power requirement of the device.
 Whether the power cable is correctly connected.
 Whether the device is correctly connected to the ground on the rear side.

1.6.2 Powering On the Device
After connecting the power cable, turn on the power switch. When the Power indicator turns on, the system starts
to initialize. When other indicators blink three times and the Power indicator is always on in green, the power
works normally.
1.7 Device Upgrade
You can upgrade software through any Ethernet port for ES-5208P. After software upgrade is complete, the system
reboots automatically.

Chapter 2 Web Configuration and Management
The system does not support the CLI and telnet management. It supports the web management only. This section
describes the web configuration and management.
2.1 Preparation Before Login
Before accessing the switch, ensure the communication between PC and switch is normal. Check the
communication as follows.
1. Set the IP address of the PC to 192.168.2.X
2. (1~254) and the subnet mask to 255.255.255.0.
3. Enter arp -d or arp -d 192.168.2.1 in the DOS window. See the following figure.
4. Ping the maintenance IP address (192.168.2.1 by default) of the switch. See the following figure.

If the PC can read the MAC address of the switch and can ping through the maintenance IP address of the switch,
that means the communication of the PC and the switch is normal.
2.2 Logging In to the Switch
To login to the web management interface and configure the switch’s settings, connect a computer to the switch
using an Ethernet cable. Open a web browser and go to the switch’s IP address. The default IP address is
192.168.2.1. Your computer’s IP address must be in the same subnet as the switch. For the default IP address this
is any IP address in the range 192.168.2.x (x = 2 –254). You can modify the IP address of your computer if you
need.
1. Enter the switch’s IP address (192.168.2.1) in the URL bar of a web browser. IE 7 or above is
recommended.
2. At the following screen login with the default username “admin” and password “1234”.
After logging in to the switch successfully, the following page appears.
Default IP address
192.168.2.1
Default user name(ID)
admin
Default password
1234

2.3 System Management
Choose Administrator, and the sub-menus of Administrator are shown as below.
2.3.1 Authentication Configuration
Choose Administrator > Authentication Configuration, and the following page appears. Read the Note in the
page, and change the user name and password. After proper configuration, click Update to apply the settings and
then Reboot the device for the changes to take effect.

2.3.2 System IP Configuration
Choose Administrator > System IP Configuration, and the following page appears. In this page, you can set the
maintenance IP address of the switch, subnet mask, and gateway. After proper configuration, click Update to
apply the settings and then Reboot the device for the changes to take effect.
2.3.3 System Status
Choose Administrator > System Status, and the following page appears. In this page, you can view the MAC
address, number of ports, and system version. You can also set a comment.
2.3.4 Loading Default Settings
Choose Administrator > Load default setting and the following page appears. In this page, click Load to load the
default settings that do not include IP address, user name, and password.

2.3.5 Firmware Update
Choose Administrator > Firmware Update, and the following page appears. In this page, enter the login password.
Then click Update. A pop up page will appear asking you to select new file for updating the firmware.
Caution : When firmware update is in progress, do not shut down the switch.
2.3.6 Reboot the Device
Choose Administrator > Reboot Device, and the following page appears. In this page, click Confirm to reboot the
device.
2.4 POE
Choose POE, and the submenus of POE are shown as below.

2.4.1 PoE Status
Choose PoE>PoE Status and the following page appears.
2.4.2 PoE Setting
Choose PoE >PoE Setting and the following page appears.
2.4.3 PoE Power Delay
Choose PoE >PoE Power Delay and the following page appears.

2.4.4 PoE Scheduling
Choose PoE >PoE Scheduling and the following page appears.
2.4.5 NTP Setting
Choose PoE >NTP Setting and the following page appears

2.5 Port Management
Choose Port Management, and the submenus of Port Management are shown as below.
2.5.1 Port Configuration
Choose Port Management > Port Configuration, and the following page appears. In this page, you can set Tx/Rx
Ability, Auto-Negotiation, Speed, Duplex, Pause, Backpressure, and Addr. Learning of port.

2.5.2 Port Mirroring
Choose Port Management >Port Mirroring, and the following page appears. In this page, you can enable port
mirroring service. The packets from source port transmit to destination port.
2.5.3 Bandwidth Control
Choose Port Management >Bandwidth Control and the following page appears.
After proper configuration, click Update to apply the settings. Click Load Default to restore the default settings.

2.5.4 Broadcast Storm Control
Choose Port Management >Broadcast Storm Control and the following page appears.
2.6 VLAN Setting
In large networks, routers are used to isolate broadcast traffic for each subnet into separate domains. This
switch provides a similar service at Layer 2 by using VLANs to organize any group of network nodes into separate
broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms
in large networks. This also provides a more secure and cleaner network environment.
The system supports VLAN based on port and VLAN based on tag. You can change the VLAN mode in the VLAN
Mode page.
Choose VLAN Setting, and the sub-menus of VLAN Setting are shown as below.

2.6.1 VLAN Mode
2.6.1.1 VLAN Based on Port
Choose VLAN Setting >VLAN Mode, and the following page appears. The default mode is Port Based VLAN.
Click Change VLAN mode to change the VLAN mode.
Once "Change VLAN mode" is selected, a warning message will appear. Select "Continue" to change the mode or
select "Back" to keep the existing vlan mode.
2.6.2 VLAN Member
2.6.2.1 VLAN Based on Port
Choose VLAN Setting >VLAN Member, and the following page appears.

2.6.2.2 VLAN Based on Tag
When the VLAN mode is tag, the VLAN Member Setting page is shown as the following figure.
The following figure displays the VLAN configuration in the tag mode