Edsal Muscle Rack URWB-3 User manual

Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.
Heavy Duty 3’
1 Drawer Work Bench
MODEL NUMBER
URWB - 3
URWB
URWB
URWB -
-
-3 3 Shelf 1 Drawer
3 3 Shelf 1 Drawer
3 3 Shelf 1 Drawer -
-
-72”h x 18”d x 36”w
72”h x 18”d x 36”w
72”h x 18”d x 36”w
Description
Top Back Post Right
Top Back Post Left
Bottom Back Post
Front Post
Braces
Beams
Left Top Support Extension
Right Top Support Extension
Top Shelf Flat Beam
Left Drawer Mount
Right Drawer Mount
Left Drawer Slide
Right Drawer Slide
Front Drawer Shelf Brace
Back Drawer Shelf Brace
Steel Peg Board
Laminate Shelves
Laminate Drawer Shelf
Laminate Top Shelf
Nuts, Bolts, Washers
Handle
Wall Anchor
Post Connector
Qty.
1
1
2
2
4
4
1
1
2
1
1
1
1
1
1
2
2
1
1
8
1
2
1
Part Number
RUPTSPR3702S
RUPTSPL3702S
RUPTSP3802S
RUPT3502S
RUBE1702
RUBE3502
RWTE0902L
RWTE0902R
RMBE3502
SVRWDM1705L
SVRWDM1705R
SVRWDS1403L
SVRWDS1403R
SVRWDB3102F
SVRWDB3102B
SPGBD1536
RPB21836LM
RPB31011LM
RPB2369LM
NB8
HDL1000
N/A
N/A
Part Size
36”
36”
38 3/8”
35”
18”
36”
9”
9”
36”
N/A
N/A
N/A
N/A
31”
31”
15 3/4” x 36”
18” x 36”
11” x 31”
9” x 36”
N/A
N/A
N/A
N/A
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and
fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Edsal manufacturing facility at, [phone] and request customer service. We can
also be reached on the internet at the following email address : [e-mail].
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com
MADE IN CHINA
Required Tools
Required Tools
Required Tools
- Rubber Mallet

Take one (1) 38 3/8” bottom back post (top end has a
half slot hole), and (1) 36 top right back post (top has
slot holes, bottom has rivets) and create a coupled back
post. Take one (1) 18” brace (shelf ledge up), and one
(1) 35” front post and attach the rivets of the brace to
the top two (2) holes of the front post. Take the coupled
back post and attach the opposite rivets to the holes so
the brace is level. Tap brace down to seat. Attach the
bottom 18” brace to the front post skipping one (1)
hole from the bottom, and the opposite end level to
the coupled back post. Tap brace down to seat. Take
one (1) drawer mount and insert the rivets one (1) slot
hole below the 18” top brace on both ends, and tap to
seat. Repeat steps for the opposite end assembly.
Assembly Instructions for URWB
Assembly Instructions for URWB
Assembly Instructions for URWB -
-
-3
3
3
Take Four (4) 36” beams with the shelf ledge facing
up, and attach two (2) even with the end assembly's
bottom braces, and two (2) even with the braces at the
top. Install one (1) back 36” Flat beam with the bend
facing down, to the top holes of the top back posts.
Take the two (2) support extensions, and Install one (1)
36” Flat beam with the bend facing down, to the front
holes of the top support extensions to create the top
shelf assembly. Take the support extension’s rivets of
the assembly, and Install the top shelf assembly even
with the rivets of the 36” back Flat beam of the unit.
Place the two (2) halves of the peg board to the inside of the
back post of the work bench. Align the holes of the peg
board to holes on the back post. Fasten using the nuts and
bolts provided. Take two (2) drawer slides, one (1) silver,
and one (1) black 31” Flat drawer braces. With the bend
facing down, insert the rivets of the black brace into the slot
and half slot holes located on the back end of the drawer
slides. Insert the laminated shelf, and install the silver front
drawer brace to the front of the drawer slides. Install the
drawer assembly to the drawer mounts slides of the unit.
Install the handle to the front drawer brace, and add the
laminate shelves to the top shelf, bottom shelf, and work
surface to finalize the assembly of the workbench. Op-
tional anchor hardware is supplied with this unit so the
unit can be fastened to a wall if necessary.
Step
1
Step
2
Step
3
Step
4
Post are directional.
The slot must point
down.
Shelf Ledge Up
Skip Hole From Bottom
Tap Lightly
Two (2) Piece
Peg Board
(Bolts at the post)
Top
Right
Back
Post
(36”)
Right Side
Drawer Mount
38 3/8”
Bottom Post
18” Brace
36” Top
Right Back Post
35” Front Post
Bottom
Back
Post
(38 3/8’”) 36” Beams
(Ledge Up)
36” Flat Beam
(Bend Down)
Top Support
Extensions
Peg Board
Fastens at
These Points
(opposite side also)
36” Flat Beam
(Bend Down)
Laminate
Shelf
Right Side
Drawer Slide
Silver Flat Drawer Brace (front)
(Bend Down)
Black Flat Drawer Brace (rear)
(Bend Down)