Edsal VR400BLK User manual

Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. DO NOT OVERLOAD. Evenly distribute the weight on each level
and always keep the heavier loads on the bottom. Use care when working with metal parts.
Boltless
Steel Shelving
MODEL NUMBER
VR400BLK
VR-400
D - Wood Shelf
A - Beams
B - Braces
C - Post
E - Post Coupler
VR
VR
VR-
-
-400 / VR400BLK
400 / VR400BLK
400 / VR400BLK -
-
-4 Shelf
4 Shelf
4 Shelf -
-
-60”h x 16”d x 36”w
60”h x 16”d x 36”w
60”h x 16”d x 36”w
Description
A - Beams
B - Braces
C - Post
D - Wood Shelf
E - Coupler
Qty.
8
8
8
4
8
Part Number
HMBE 3404 (GY / BLK)
HMBE 1603 (GY / BLK)
HMPT 3003 (GY / BLK)
RPB21636
HIPC0200
Part Size
34 27/32”
14 27/32”
30”
16” x 36”
2 1/2” x 7/8”
General Instructions
General Instructions
General Instructions
Assembly is done with the tabs of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the tabs properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the tabs are straight and
fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our manufacturing facility at, [phone] and request customer service. We can also
be reached on the internet at the following email address : [e-mail].
To obtain replacement parts, please provide the following information :
- Model # - Part #, Description, & Color - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com
Tools Necessary For Assembly
Tools Necessary For Assembly
Tools Necessary For Assembly
Rubber Mallet
Note: TAP GENTLY ! A Hammer could be used
with a cloth or a wood block to protect the parts.

Assemble two (2) post with one (1) brace (see figure A). The
flat angled edge of the brace be facing up. Skipping one (1)
slot from the bottom, slide the tabs of the brace into the slots of
the post and tap down gently to properly seat (see figure B).
Repeat this process using two (2) post and one (1) brace.
Attach the assembled end units with two (2) beams (see figure
C). Again Skipping one (1) slot from the bottom, slide tabs of
the beams into post slots and tap down gently to properly seat.
Assembly Instructions for VR
Assembly Instructions for VR
Assembly Instructions for VR-
-
-400 & VR400BLK
400 & VR400BLK
400 & VR400BLK
Start by adding a wood shelf to the level previously built, then
continue working by adding the second level using two (2)
beams and two (2) braces in the post slots of your desired
location. Again slide the tabs of the beams and braces into the
post slots and tap gently to properly seat.
IMPORTANT NOTE : Make sure all beams and braces are fully seated into the post slots.
IMPORTANT NOTE : Make sure all beams and braces are fully seated into the post slots.
IMPORTANT NOTE : Make sure all beams and braces are fully seated into the post slots.
Add a wood shelf to the previously built level, then assemble
the top post to the bottom post by using eight (8) of the post
couplers. Slide the couplers tabs into the top of the bottom
post, tap gently to properly seat. Slide the top post onto the
remaining tabs of the couplers, tap the top post down to
properly seat (see figure D). Install the third level above the
post couplers, using two (2) beams, and two (2) braces.
Add a wood shelf to the previously built level, then continue by
adding the final level to the unit using two (2) beams and two
(2) braces. Tap gently to properly seat and add the final wood
shelf to the top of the unit.
Step
1
Step
2
Step
3
Step
4
Figure A
Figure AFigure A
Figure A
Figure B
Figure BFigure B
Figure B
Figure C
Figure CFigure C
Figure C
Tap Lightly
Post Slot
Brace
Beam
Wood Shelf
Figure D
Figure DFigure D
Figure D
Wood Shelf
Post Coupler
Top Post
Bottom Post
Wood Shelf