Edsal MRWB-6 User manual

Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.
Heavy Duty 6’
Work Bench
MODEL NUMBER
MRWB - 6
MRWB
MRWB
MRWB-
-
-6 3 Shelf 2 Drawer
6 3 Shelf 2 Drawer
6 3 Shelf 2 Drawer -
-
-60”h x 24”d x 72”w
60”h x 24”d x 72”w
60”h x 24”d x 72”w
Description
Long Post
Brace
Beam
Short Post
Shelf Support
Top Shelf Beam
Drawer Mount
Drawer Slide
Drawer Shelf Braces
Peg Board
Wood Shelf
Center Bracket
Center Drawer Mount
Peg Board Bracket
Wood Drawer Shelf
Wood Top Shelf
Hardware
Qty.
2
4
5
2
2
1
2
4
4
1
2
2
2
2
2
1
12
Part Number
RUPT6002
RWBE2303
RWBE7103
RUPT3602
RWSB2801
RWSS8903
RWDM2305
RWDS2003
RWDB3102
PGBD7120
RLPB2472
RWBR0303
RWDM2303
RWPB0401
RPB23217
RPB2729
NB12
Part Size
60”
24”
72”
36”
N/A
N/A
N/A
N/A
32”
20” x 72”
24” x 72”
N/A
N/A
N/A
32” x 17”
9” x 72”
#10-24
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and
fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Edsal manufacturing facility at, [phone] and request customer service. We can
also be reached on the internet at the following email address : [e-mail].
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com
Heavy Duty Work Bench

Take two (2) 24” braces with the shelf ledge facing up, and
one (1) short 36” post and attach rivets from the brace to the
top two (2) holes of the short post. Take one (1) long 60”
post and attach the opposite end of the brace to the holes of
the long post so the brace is level, tap down brace to seat.
Attach the bottom brace to the short post skipping one (1)
hole from the bottom and the opposite end to the long post,
tap down brace to seat. Take one (1) drawer mount and skip
one (1) hole from the top brace and attach rivets to the
short and long post, tap down drawer mount to seat. take
one (1) drawer slide and insert it into the slide of the drawer
mount. Repeat this step for the opposite end assembly.
Assembly Instructions for MRWB
Assembly Instructions for MRWB
Assembly Instructions for MRWB -
-
-6
6
6
Take four (4) 72” beams with the bend facing up, and attach
the rivets even with the braces from the two end assembly's,
and tap down to seat. Install the top shelf beam and one (1)
72” beam with the bend facing down, to the top holes of the
back posts. Next install a peg board bracket to the beam of
the top assembly using the nuts and bolts provided. Assem-
ble the center drawer assembly by taking a peg board bracket,
one (1) shelf support, and one (1) center mounting bracket
and bolt them to the work surface back beam (see figure A).
Next bolt the shelf support bracket, and the last center mount-
ing bracket to the opposite beam. Attach the two (2) center
drawer mounts by placing the rivets into the holes of the cen-
ter mounting brackets. Insert the drawer slides into the center
drawer mount slides. Add the final shelf support to the bot-
tom two (2) beams using the nuts and bolts provided.
Place the peg board to the inside of the back post of the work
bench. Using the fourth hole from the top of the back post,
align the holes of the peg board to the holes on the back
post, and fasten using the nuts and bolts provided. Align the
holes on the peg board brackets to the holes of the peg
board, and fasten the peg board to the peg board brackets
using the nuts and bolts provided. Take the four (4) 32”
drawer shelf braces and with the shelf ledge facing down,
insert the two (2) rivets into the two (2) holes located on the
drawer slides.
Add the wood shelves to the top shelf support, the draw-
ers, the bottom shelf, and the work surface to finalize the
assembly of the workbench.
Step
1
Step
2
Step
3
Step
4
4th Hole Down
Post are directional.
The slot must point
down.
Drawer Mount
Drawer Slide
Long Post
Short Post
24” Brace
Shelf Ledge Up
Skip Hole From Bottom
Tap Lightly
Center Drawer Mount
Peg Board Brackets
Figure A
Shelf Support
Top Shelf Beam
72” Beams
Peg Board Bracket
Shelf Support
Center
Mounting
Bracket
Drawer Slides
32” Drawer Shelf Braces
(Bend facing down)
(Back of drawer slides also)
Peg Board
72” Beam
(Bend facing down)