Eighteeth Fast-Fill User manual

0197
Fast-Fill
USER MANUAL

3 / 37
Content
1. Scope of Fast-Fill............................................................................................................
1.1 Parts Identification.........................................................................
1.2 Components and Accessories.........................................................
1.3 Options (sold separately) ...............................................................
2. Symbols used in the User Manual.............................................................................
3. Before Use........................................................................................................................
3.1 Intended Use ..................................................................................
3.2 Contraindications...........................................................................
4. Installing the Fast-Fill....................................................................................................
4.1 Installation of Gutta-percha ...........................................................
4.2 Installation of Cartridge .................................................................
4.3 Installation of adapter ....................................................................
4.4 Connecting charge base .................................................................
5. Use Interface....................................................................................................................
6. Setting ...............................................................................................................................
6.1 Memory Parameter Setting ............................................................
6.2 Advanced Setting...........................................................................
7. Operation ..........................................................................................................................
7.1 Charge............................................................................................
7.2 Heating and Using .........................................................................
7.3 Changing Gutta-percha ..................................................................
8. Maintenance.....................................................................................................................
8.1 Piston cleaning...............................................................................
8.2 Changing silver tube of cartridge...................................................
8.3 Cleaning, Disinfection and Sterilization........................................
9. Troubleshooting..............................................................................................................
10. Technical Data...............................................................................................................
11. EMC Tables.....................................................................................................................
12. Statement .......................................................................................................................

1 Scope of Fast-Fill
4 / 37
1. Scope of Fast-Fill
1.1 Parts Identification
1
2
3
4
6
5
1.Charge Base
2.Handpiece
3.Cartridge nut (2PCS)
4.Silver tube (2PCS)
5. Adapter
6.Bending Tool

1 Scope of Fast-Fill
5 / 37
1.2 Components and Accessories
Fast-Fill Handpiece
(1pcs)
Charge Base (1pcs)
Adapter (1pcs)
Part
Cartridge nut (2pcs)
Bending tool (1pcs)
Silver tube (1pcs)
Size: 25Ga
Color: Black
(Disposable)
Silver tube (1pcs)
Size: 23Ga
Color: Natural
(Disposable)

1 Scope of Fast-Fill
6 / 37
1.3 Options (sold separately)
Handpiece Base

2 Symbols used in the User Manual
7 / 37
2. Symbols used in the User Manual
WAR NING
If the instructions are not followed properly,
operation may lead to hazards for the product or
the user/patient.
NOTE
Additional information, explanation of operation
and performance.
Serial number
Catalogue number
Manufacturer
Date of manufacture
LOT
Lot of manufacture
Class II equipment
Type B applied part
CE marking
Direct current
WEEE directive marking
Keep dry
134 C
Can be autoclaved up to a maximum temperature
of 134° Celsius
Authorized Representative in the European

2 Symbols used in the User Manual
8 / 37
Community
55 C
20 C
Temperature limitation
80%
20%
Humidity limitation
106kPa
70kPa
Atmospheric pressure limitation
Manufacturer’s LOGO
Consult instructions for use
Washer-disinfector for thermal disinfection
Caution, hot surface
Do not reuse

3 Before Use
9 / 37
3.Before Use
3.1 Intended Use
Fast-Fill is intended for heating and extruding Gutta-percha into cleaned and shaped
canals during root canal treatment.
This device must only be used in hospital environments, clinics or dental offices by
qualified dental personnel and not used in the oxygen-rich environment.
3.2 Contraindications
This device must not be used in cases where a patient has been fitted with an
implanted heart pacemaker (or other electrical equipment) and has been cautioned
against the use of small electrical appliances (such as electric shavers, hair dryers, etc.)
Do not use on patients with a known sensitivity to natural rubber latex or silver.
Safety and effectiveness have not been established in pregnant women and
children.
WAR NIN G
Read the following warnings before use:
1. The device must not be placed in humid surroundings or anywhere where it can come
into contact with any type of liquids.
2. Do not expose the device to direct or indirect heat sources. The device must be
operated and stored in a safe environment.
3. The device requires special precautions with regard to electromagnetic compatibility
(EMC) and must be installed and operated in strict compliance with the EMC information.
In particular, do not use the device in the vicinity of fluorescent lamps, radio transmitters,
remote controls and do not use this system near the active HF Surgical Equipment in the
hospital. Portable RF communications equipment (including peripherals such as antenna
cables and external antennas) should be used no closer than 30 cm (12 inches) to any
part of the Fast-Fill, including cables specified by the manufacturer. Otherwise,
degradation of the performance of this equipment could result. Do not charge, operate or
store at high temperatures. Comply with the specified operating and storage conditions.
4. Gloves and a rubber dam are compulsory during treatment.
5. If irregularities occur in the device during treatment, switch it off. Contact the agency.
6. Never open or repair the device yourself, otherwise, void the warranty.
7. Cautions should be exercised when use the device to fill the teeth with thin dentinal
root walls and pay more caution at temperature settings above 185℃

4 Installing the Fast-Fill
10 / 37
4.Installing the Fast-Fill
4.1 Installation of
Gutta-percha
Push the Gutta-percha into the handpiece.
NO TE
This product is not included the
Gutta-percha. Please use the Gutta-percha
that is recommended by Sifary. Refer to the
Technical data of this manual for the
recommended Gutta-percha size.
4.2 Installation of Cartridge
Screw the cartridge along the thread of the
handpiece to install.
The silver tube on cartridge cannot be
turned or bended by hand.
Use bending tool to bend the silver tube.
Use bending tool with the hexagonal hole
matched to rotate the silver tube.
Unscrew the cartridge from the
handpiece to disassemble.
WAR NING
To remove the cartridge. As shown in
the picture, touch the cartridge nut with
finger rapidly, make sure it is not hot
before operation. If the temperature is
too high, waiting 3~5 minutes till it is
cooling.
The surface temperature of the
cartridge will not exceed 55℃during
operation.
E
ven if the cartridge cools down
already, we strongly recommend not to
touch the silver tube. There is a risk of
heat injury or damaging the silver tube.
Hold the black shell to remove.

4 Installing the Fast-Fill
11 / 37
4.3 Installation of adapter
Plug the head into the base if they are
separated in the package.
4.4 Connecting charge
base
Plug the USB of adapter into the charge
base, and plug the other end into a power
outlet.
The Power LED on charge base will light
up in green.
NO TE
Only the original adapter can be used.
Put the handpiece all the way into the
charge base. The charge state will show
on the screen.
NO TE
Put the handpiece into the charge base
in the right direction, otherwise the
handpiece will not be charged.
If only need a base to put the device on
dentist element of dental chair (without
charge function), handpiece base is
recommended to use instead of charge
base.
Power LED

5 Use Interface
12 / 37
5.Use Interface
1
2
3
4
5
①Main switch
②Indicator light
③Display Screen
④Set switch
⑤Power switch
Turn Power On
Long press .
Change Memory
Shot press to change temperature
memory from T1 to T3.
Memory Parameter Setting
During standby state, holding down press
more than 2 seconds to enter
memory parameter setting. Parameter T1
to T3 can be set independently. Press
till target setting, press to adjust, then
press to confirm.
Heating
During standby state, shot press and
the indicator light flashes.
Stop heating
During heating state, shot press .
Pushing out Gutta-percha
When the heating is completed, the
indicator light will be on. Holding down
press .
Turn Power Off
Long press more than 2 seconds.
Advanced setting
During power off state, holding down
press then press to enter
advanced setting. Press till target
setting, press to adjust, then press
to confirm.

6 Setting
13 / 37
6.Setting
6.1 Memory Parameter Setting
Fast-Fill has 3 memory programs
(T1,T2,T3), press to change during
standby state, the memory number will
change accordingly.
During any memory, holding down press
in 2 seconds, the “Temperature” of this
memory can be changed.
Press till target temperature, the
temperature can be set from 100℃to
200℃.
Press to confirm and enter next
interface.
The “Push Speed” of this memory can be
changed.
Press till target speed, the speed can
be set Low, Mid, High.
Press to confirm and enter next
interface.
The “Change GP” can be chosen.
Confirm the Gutta-percha need to change
or not, press to adjust.
If choose “No”, Press to confirm and
return to standby interface.
If choose “Yes”, see chapter 7.3 Changing
Gutta-percha for more information.

6 Setting
14 / 37
6.2 Advanced Setting
AutoPowerOff
Mi n
5
During power off state, holding down press
then press to enter advanced setting,
the “AutoPowerOff” will appear on the display
screen. Press to adjust, the auto power
off time can be set to 5, 10 and 15 minutes.
Press to confirm and enter next
interface.
Beep Volume
Vol 1
The “Beep Volume” can be changed. Press
to adjust. The “Beep Volume” can be set
to 0, 1 and 2.
Press to confirm and enter next
interface.
RestoreSettings
NO YES
The “RestoreSettings” can be changed.
Press to adjust, press to confirm and
enter next interface.
NOTE
If choose “YES”, all the setting parameters
will be covered by factory settings.
Save
NO YES
The “Save” can be chosen.
Confirm the setting need to save or not, press
to adjust, press to save and power
off.

7 Operation
15 / 37
7.Operation
7.1 Charge
Display the present remaining amount of the battery.
Less than 15% remains, please charge.
NOTE
If the power if less than 15%, the device must be
recharged within 30 days, otherwise the battery will
be damaged.
Alt e rn ati ve charging meth od
Charge without charge base is also available,
connect adapter to handpiece directly, the charge
state will show on the screen.
Charge with charge base is recommended (See
chapter 4.4 Connecting charge base)
NO TE
Only the original adapter could be used.
Do not use the handpiece during the charging.
Charging indication appears on the screen, and
flashes slowly, when battery is fully charged or in a
state near full charge, the flash will stop. Fully
charged will take about 4 hours, depending on
residual battery power and battery state.
It can be recharged 300-500 times, depending on the
operating conditions of the device.
WAR NIN G
Do not change the battery, only trained technician or
distributor can change the battery. The electronic
parts will be damaged if use a wrong battery or install
with a wrong way.

8 Maintenance
16 / 37
7.2 Heating and Using
Shot press to heat the cartridge during standby
state.
NOTE
Push out insufficiently warmed Gutta-percha about
10mm before each use.
The LED flashes in blue slowly during heating.
When up to target temperature, the flash will stop
and stay in blue.
WAR NING
If the handpiece is not operated for a long time
after the heating completed, press to stop
heating.
Do not place the heated cartridge in the root canal
for more than 5 seconds to prevent thermal injury
to the patient.
1
Heating indication, When the set temperature is
reached, heating process will switch off and “”
will display on screen.
2
Direction of pushing
3
Real time heating temperature
4
Gutta-percha residual
After heating completed, hold down press to
push out Gutta-percha. At the same time,
1
the
light of direction flashes,
2
the residual
Gutta-percha bar will change according. Press
to exit and return to standby interface.

8 Maintenance
17 / 37
NOTE
If there is a little residual Gutta-percha in handpiece or cartridge, tighten the
cartridge again to prevent leak Gutta-percha after heating.
If there is too much residual Gutta-percha in handpiece or cartridge, please refer to
daily cleaning process.
Please use good mobility Gutta-percha, otherwise the Gutta-percha will leak. If
leaking please refer to daily cleaning process.
7.3 Changing Gutta-percha
During standby state, holding down press in 2
seconds to enter memory parameter setting. Press
till “Change GP”. Press till “Yes” and press to
confirm.
Heating...
Firstly, the handpiece will heat to about 150℃to melt
the residual Gutta-percha.
Secondly, the pushrod pushes forward until the
Gutta-percha is exhausted. the direction of push rod
movement displays on the screen.
Then, the direction and position of push rod display on
the screen. The push rod needs returning to original
position. This operation takes about 50 seconds.
Finally, when the pushrod is back to original position,
“Please insert GP” will display on the screen. Press
any key to exit and return to standby interface.
NO TE
During this state, press can stop and return to standby interface.

8 Maintenance
18 / 37
After pushing the Gutta-percha bar into handpiece with
medical forceps, screw down the cartridge.
NO TE
If there is some Gutta-percha in the handpiece, it is
inconvenient to install the Gutta-percha bar. Push the
residue to the bottom of cavity with the pin on bending
tool.

8 Maintenance
19 / 37
8.Maintenance
8.1 Piston cleaning
Piston cleaning
150℃
Heat to 150℃to melt Gutta-percha, then remove
the cartridge.
NO TE
A small amount of Gutta-percha residue have no effect of
function.
Dispose of the silver tube and then clean the residue
inside the cartridge nut with medical forceps.
Clean the overflow Gutta-percha on the top of the
handpiece with medical forceps.
When the medical forceps cannot get into the cavity
to clean, Heat the handpiece to about 150℃, then
unscrew the “Cleaning Nut” with the bending tool.
NOTE
Heating to 150℃to avoid damaging the “Cleaning Nut”.
Clean the inside of nut with medical forceps.

8 Maintenance
20 / 37
Heat the handpiece to about 150℃. Then install the
“Cleaning Nut” to the handpiece after cleaning is
completed.
8.2 Changing silver tube of cartridge
The silver tubes of cartridge are single use only and should only be used on one patient.
It can be replaced according to the following steps.
Cut the broken silver tube from the step where the
arrow indicates with knife.
Push out the silver tube with the bottom plane of
the bending tool.
Unscrew the cap from the cleaning rod.

8 Maintenance
21 / 37
As shown, push out the silver tube completely
with the cleaning rod.
Insert the new silver tube as shown in the figure.
NOTE
Remove the protective cover before installation.
There are two different specifications of the silver
tube:
Part number:6351208 size: silver tube (25Ga)
Part number:6351209 size: silver tube (23Ga)
Need to order from distributor.
Screw the cap into the cleaning rod.
Push the cleaning rod against the bottom of the
silver tube and press it into place.
NOTE
If the installation is not in place, please contact
the supplier to use professional tools for
maintenance.