Eizo SCD 19102 User manual

Instructions for Use
1.3 MP 19" LCD Monitor
Important
Please read the safety information and all information delivered
with the product carefully to familiarize yourself with safe and
effective usage.

EIZO GmbH
Siemensallee 84
76187 Karlsruhe
Germany
A5E01588521A-006
08/2015 Technical data subject to change.
Copyright © EIZO GmbH 2015.
All rights reserved.
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to
prevent damage to property. The notices referring to your personal safety are highlighted in the manual
by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These
notices shown below are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that material damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of
danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a
warning relating to property damage.
Qualified personnel
The product/system described in this documentation may be operated only by personnel qualified for
the specific task in accordance with the relevant documentation, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are ca-
pable of identifying risks and avoiding potential hazards when working with these products/systems.
Use of EIZO products
WARNING
EIZO products may only be used for the applications described in the catalog and in the relevant tech-
nical documentation. If products and components from other manufacturers are used, these must be
recommended or approved by EIZO. Proper transport, storage, installation, assembly, commissioning,
operation and maintenance are required to ensure that the products operate safely and without any
problems. The permissible ambient conditions must be complied with. The information in the relevant
documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of their respective owners. Please refer to the
trademarks listed in the appendix. The remaining trademarks in this publication may be trademarks
whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of liability
We have reviewed the contents of this publication to ensure consistency with the hardware and soft-
ware described. Since variance cannot be precluded entirely, we cannot guarantee full consistency.
However, the information in this publication is reviewed regularly and any necessary corrections are in-
cluded in subsequent editions.

Tableofcontents
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 3
Table of contents
Legal information ............................................................................................................. 2
1 Introduction....................................................................................................................... 6
1.1 Contents of this document ........................................................................................6
1.2 Intended use .............................................................................................................6
2 Safety instructions ........................................................................................................... 7
2.1 General safety notes ................................................................................................7
2.2 Product-specific safety instructions ........................................................................12
3 Description...................................................................................................................... 13
3.1 Scope of delivery ....................................................................................................13
3.2 Performance features .............................................................................................13
4 Setup and installation .................................................................................................... 15
4.1 Installation site ........................................................................................................15
4.2 Installing the monitor...............................................................................................16
5 Connecting...................................................................................................................... 17
5.1 General connection information..............................................................................17
5.2 Connector location..................................................................................................18
5.3 Overview of signals and connections .....................................................................18
5.4 Connection panel....................................................................................................19
5.5 Connecting the signal cable....................................................................................20
5.6 DIP switches (for SMD 19102 only)........................................................................21
5.7 Connecting the power cable ...................................................................................21
5.8 Installing the base and cable (SCD 19102) ............................................................22
5.9 Serial interface........................................................................................................25
6 Start-up............................................................................................................................ 27
6.1 Switching on the monitor ........................................................................................27
6.2 Operator controls ....................................................................................................27
6.3 Description of OSD menu .......................................................................................28
6.3.1 OSD overview ........................................................................................... 28
6.3.2 Menu functions.......................................................................................... 29
6.3.3 Exit OSD ................................................................................................... 40
6.3.4 Service level 2 functions ........................................................................... 40
6.3.5 Lock/unlock OSD menu ............................................................................ 50
6.4 System settings ......................................................................................................51
6.4.1 Avoiding image sticking ............................................................................ 51
6.4.2 Setting the image geometry ...................................................................... 51
6.4.3 Setting brightness and contrast ................................................................ 51

Tableofcontents
4SCD 19102 / SMD 19102 Instructions for Use, 08/2015
6.4.4 Monitor adjustment – video source/graphics card .................................... 52
6.4.5 Monitor adjustment – LUT......................................................................... 53
6.4.6 Monitor adjustment - Force Mode ............................................................. 54
7 Operation......................................................................................................................... 67
7.1 Note for users .........................................................................................................67
8 Cleaning and maintenance ............................................................................................ 68
8.1 Cleaning..................................................................................................................68
9 Troubleshooting ............................................................................................................. 70
9.1 Troubleshooting ......................................................................................................70
10 Technical specifications ................................................................................................ 71
10.1 Graphic display .......................................................................................................71
10.2 Voltage supply ........................................................................................................72
10.3 Electronics ..............................................................................................................72
10.4 Inputs/Outputs ........................................................................................................72
10.5 Controls and connectors.........................................................................................73
10.6 Mechanical design ..................................................................................................74
10.7 Climatic conditions..................................................................................................74
10.8 Mechanical requirements........................................................................................75
10.9 Safety specifications ...............................................................................................75
10.10 Electromagnetic compatibility .................................................................................76
11 Dimensioned drawings .................................................................................................. 77
11.1 SCD / SMD 19102 C/CP (without stand) ................................................................77
11.1.1 Front view ................................................................................................. 77
11.1.2 View from left ............................................................................................ 78
11.1.3 Rear view .................................................................................................. 79
11.1.4 View from above ....................................................................................... 79
11.2 SCD / SMD 19102 D (with stand) ...........................................................................80
11.2.1 Front view ................................................................................................. 80
11.2.2 View from left ............................................................................................ 81
11.2.3 View from above ....................................................................................... 81
12 Spare parts / accessories .............................................................................................. 82
12.1 Monitor stand ..........................................................................................................82
12.2 DVI transmission path and cable ............................................................................82
13 Appendix ......................................................................................................................... 84
13.1 Markings and symbols ............................................................................................84
13.2 Warranty .................................................................................................................85
13.3 Repairs ...................................................................................................................85

Tableofcontents
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 5
13.4 Environmental protection ........................................................................................85
13.5 Additional devices...................................................................................................85
13.6 Contact ...................................................................................................................85
13.7 Trademarks.............................................................................................................86
13.8 China RoHS (Restriction of Hazardous Substances) .............................................87
13.9 China RoHS (Restriction of Hazardous Substances) .............................................89
13.10 Disposal of materials containing mercury ...............................................................91
Index ................................................................................................................................ 93

Introduction
1.1Contentsofthisdocument
6SCD 19102 / SMD 19102 Instructions for Use, 08/2015
1 Introduction
1.1 Contents of this document
This document explains the functionality and the approved application of the:
• SCD19102
• SMD 19102
To ensure clarity, it does not contain all detailed information on this product.
The contents of this document are neither part of a previous or existing agreement, commit-
ment or legal relationship, nor does it modify such.
The monitors are available in color and gray scale variants:
• Color monitor
– SCD 19102 C, version without protective front pane, without multifunctional stand
– SCD 19102 CP, version with protective front pane, IPx2 at front
– SCD 19102 D, version without protective front pane, with multifunctional stand
• Gray scale monitor
– SMD 19102 C, version without protective front pane, without multifunctional stand
– SMD 19102 CP, version with protective front pane, IPx2 at front
– SMD 19102 D, version without protective front pane, with multifunctional stand
Note
This documentation is available in electronic format only. It is loaded on the CD-ROM that
has been provided and can be downloaded from the www.eizo.com web site.
1.2 Intended use
The SCD / SMD 19102 has been specifically designed for medical imaging, with the excep-
tion of mammography. The monitor is intended for installation in a ceiling or wall mount, or
for installation in a base.
The monitor is intended to be used by health care professionals to display the video sources
from various commercially-available devices (with the exception of mammography) com-
monly used in a medical environment, on a single video monitor.
The modality application requires monitors with internal factory preset Look Up Tables in or-
der to adapt the monitors to the human visual system. These monitors do not have to be
calibrated on site.
The SCD / SMD 19102 has five internal factory preset Look Up Tables.

Safetyinstructions
2.1Generalsafetynotes
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 7
2 Safety instructions
Ensure that all necessary steps are taken to avoid injuries or incorrect diagnoses.
No zero error rate
LCD monitors do not have a zero error rate. For this reason, the image parameters can
change over time, e.g. reduced luminance or changing/fading colors.
Note
Image quality
To maintain constant image quality, EIZO recommends cleaning the monitor on a regular
basis and checking image properties in accordance with all applicable local regulations.
User
In the following, health personnel such as surgeons or medical technicians (MTA)s are re-
ferred to as the "user".
2.1 General safety notes
Correct and safe operation of EIZO devices assume professional transport, storage, installa-
tion, and connection, as well as careful operation and service.
The devices may only be used for applications for which they are intended.
For safety reasons, the following precautions must be observed:

Safetyinstructions
2.1Generalsafetynotes
8SCD 19102 / SMD 19102 Instructions for Use, 08/2015
DANGER
Please observe all warning information present on the device and in the instructions for use.
There is a danger to life if warnings are not obeyed. Severe personal injury or damage to property
may occur.
Observe the safety requirements of EN 60601-1 (IEC 60601-1)
To prevent injury to patients and users, connect the electrical system in accordance with the safety
requirements of EN60601-1 (IEC60601-1) for "Safety requirements for medical electrical systems".
Connecting the protective earth conductor
If the device is connected to line power, the device must be connected to a protective ground con-
ductor. This is the only way to ensure that the touch leakage current in a first fault event does not ex-
ceed 500 µA.
The interruption of the device's protective conductor is considered a first fault event in accordance
with EN 60601-1.
Use the following measures to ensure that the leakage currents remain below the specified limits:
• Separators for signal input unit or signal output unit
• Use of a safety isolating transformer
• Use of the additional protective ground terminal
Mounting of the monitor: The monitor's suspension arm must have its own protective ground conduc-
tor. This protective ground conductor guarantees, together with the protective ground conductor of
the monitor, that the housing leakage current always remains less than 500µA, even in the event of
a single fault condition.
No unauthorized opening of the device / no unauthorized service or maintenance work
The device may only be opened by qualified personnel. Likewise, service or maintenance work may
only be carried out by qualified personnel. There is a risk of electric shock.
No liability is accepted for death and injury to persons or damage to property resulting from work car-
ried out by non-qualified personnel.
Do not touch components in the device
If the device is connected to the line power, components in the device are subjected to high voltages.
Touching the components may be fatal.
No contact between device and patients
The device is not suitable for direct contact with a patient. The device and patient must never be
touched simultaneously. Otherwise there is a danger to life and limb.

Safetyinstructions
2.1Generalsafetynotes
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 9
DANGER
Please observe all warning information present on the device and in the instructions for use.
There is a danger to life if warnings are not obeyed. Severe personal injury or damage to property
may occur.
Never use defective power cables
If a damaged or unsuitable power cable is used, it could result in a fire or electric shock. Only use
power cables with PE contacts approved by the manufacturer.
Disconnect the power cable correctly
When disconnecting the power cable, always do so by holding the plug. Ensure that your hands are
dry. There is a risk of electric shock.
Do not insert any objects into the housing
Objects inserted into the housing may result in an electric shock or damage to the device.
Do not place any objects on top of the device
If you place objects on top of the device, this can lead to overheating and fire.
Avoid penetration of liquid
Liquids seeping into the device may result in electric shock or device failure.
CAUTION
Extensive damage to property may result if the device is not connected correctly
That is why you should observe the warning information:
Connection must be carried out by specialists
Please ensure that all steps are taken to avoid injuries or incorrect diagnoses.
• Only use the video cables specified by the manufacturer for the connection.
• Only use power cables with PE contacts.
• Only use power outlets with PE contacts.
• Do not connect too many devices to a power outlet or extension cable.
• Observe the information provided by the respective manufacturer.
• If required by the application or local regulations, QA software must be used for quality control
and documentation.
Connection in the USA and Canada
Molded power supply plugs must comply with the requirements for "hospital grade attachments" CSA
Std. C22.2 No.21 and UL498.
Connection in China
Only use power cables approved for China. These power cables are identified by the labels "CCC" or
"CQC".
Observe the country-specific regulations
Observe all regulations of the country in which the device is used.

Safetyinstructions
2.1Generalsafetynotes
10 SCD 19102 / SMD 19102 Instructions for Use, 08/2015
NOTICE
Extensive damage to property may result if the device is not connected correctly
That is why you should observe the warning information:
• Desktop installation:
Place the device on a solid and level surface. The attached stand, as well as the installation sur-
face, must be suitable for the weight of the device.
• For mounting on a wall or ceiling suspension:
The mount unit must be suitable for the weight of the device.
• For installation in a rack:
Observe the installation sequence, and provide ventilation for the device.
Provide adequate air circulation
When installing the device, ensure that there is adequate air circulation for operation. The permissi-
ble ambient temperature range must not be violated. Otherwise, the device could be destroyed by
overheating.
Avoid sources of heat
Do not install the device in the vicinity of sources of heat, such as radiators, heating appliances or
other devices that can generate or emit heat.
Do not subject the device to jolting or shocks
The device contains sensitive electronic components that could be damaged by jolting or shocks.
Only switch on a cold device following adaptation to room temperature
If the device is brought into a room with a higher or rising temperature, condensed water will form in
and on the device. Do not switch on the device until the condensed water has evaporated. Other-
wise, the device could be damaged.

Safetyinstructions
2.1Generalsafetynotes
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 11
NOTICE
Extensive damage to property may result if the device is not connected correctly
That is why you should observe the warning information:
Transportation only in original packaging
Use the original packaging for transportation, and transport in the correct shipping position. Be sure
in particular to protect the monitor LCD modules from shocks.
Care of device / cleaning agents
• Remove water drops immediately; extended contact with water discolors the surface.
• Only clean the surfaces using the cleaning agents referred to in the Instructions for Use.
• Monitor: The screen is extremely sensitive to mechanical damage. Absolutely avoid scratches,
shocks, etc.
What to do if the device is faulty
If the following conditions exist, the device must be disconnected from the line power supply and
checked by qualified personnel:
• Damage to the plug or power cable.
• After liquid seeps into the device.
• If the device has been exposed to moisture.
• If the device does not function or if a fault cannot be eliminated using the Instructions for Use.
• If the device has been dropped and/or the housing damaged.
• If the device smells of burning or makes peculiar noises.
Be aware of the monitors aging
Note that monitors can fail as a result of aging, and that image properties such as brightness, con-
trast,and color value can change.
Do not touch the monitor screen
Due to mechanical pressure or electrostatic discharges, touching the screen can result in brief distur-
bances to the image.

Safetyinstructions
2.2Productspecificsafetyinstructions
12 SCD 19102 / SMD 19102 Instructions for Use, 08/2015
2.2 Product-specific safety instructions
CAUTION
If the SCD / SMD 19102 is installed on a stand:
Adjust the monitor height carefully, otherwise there is a risk of injury
When adjusting the height of the monitor, make sure that you do not trap your fingers or
any other objects.
CAUTION
Ensure monitor stability
The stability of the monitor must be ensured following installation of the stand/holder. The
screw insertion depth into the monitor must be between 7 and 9mm.
CAUTION
Subsequent installation of a stand
The SCD / SMD19102C and SCD / SMD19102CP monitors are delivered without a
stand. To ensure that a system comprising a monitor and base meet the requirements of
standard EN60601, select a stand for subsequent installation that meets this standard.

Description
3.1Scopeofdelivery
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 13
3 Description
3.1 Scope of delivery
Note
Keep the packaging material for subsequent transport of the device.
All SCD / SMD 19102 monitors are delivered with the following components:
• CD with instruction manual
• European power cable
• US power cable
• Chinese power cable
• DVI-D video cable
3.2 Performance features
SCD 19102 19" color monitor and SMD 19102 19" gray scale monitor have the following
features, which permit a wide area of applications.
Compact design
The monitor benefits from low weight and a small foot print, as well as improved perfor-
mance, when compared to conventional CRT monitors. Thanks to the equally narrow border
on each edge, the monitor fits into any environment, and is ideally suited to both desktop
and ceiling suspension.
Perfect picture reproduction thanks to LCD technology
The use of LCD technology eliminates picture geometry distortions and color spots.
The monitor delivers flicker-free images even at low border rates (60 Hz). The monitor thus
meets the strictest ergonomic requirements.
Modification of gray scale setting
In medical applications (e.g. for radiography, computed tomography, and MRI), where pic-
tures are usually displayed in shades of gray, the gray values can be adapted to the user's
eye. This calibration is performed at the factory and is therefore available when shipped
(factory calibrated monitor). In addition, five different settings (Look Up Table – LUT) are
saved in the monitor. To switch to a different LUT, please speak to service personnel, who
will make the change using the On-Screen Display (OSD) or the QA software.
Screen resolution
The monitor is equipped with an active 19" TFT display that has an extremely wide viewing
angle. The monitor offers maximum gray scale contrast across a very wide viewing angle
(in-plane switching (IPS) technology). The optimum screen resolution is 1280x1024pixels.

Description
3.2Performancefeatures
14 SCD 19102 / SMD 19102 Instructions for Use, 08/2015
Video signals with other resolutions, as are common in medical technology, are enlarged or
reduced to fit the screen size optimally. Alternatively, they can be displayed in their original
size (1:1).
RGB input (15-pin Sub-D/DVI/BNC)
SCD19102
• The monitor is connected to the computer system using either the 15-pin Sub-D input
socket or the DVI-I input socket.
SMD 19102
• The monitor is connected to the computer system using either the 15-pin Sub-D input
socket, the BNC sockets or the DVI input socket (digital only).
If necessary, the monitor display is adapted using an OSD menu.
Video inputs
The SCD19102 and SMD 19102 monitors have two additional analog video inputs. As a re-
sult, the monitor can operate with standard analog video signals (PAL/NTSC). The RGB and
video inputs can be connected simultaneously to different signal sources.
Force Mode
Using the Force Mode function, the SCD19102 and SMD 19102 monitors can be adapted
to special timing settings.
Protective glass
The SCD19102CP and SMD19102CP have anti-glare protective glass fitted over the top
of the LCD panel to protect the surface of the panel against bumps and scratches. The front
of the monitor is protected against moisture (IPx2 protection). The space between the pro-
tective pane and the panel is sealed to prevent dust from entering, thus helping ensure the
internal surfaces remain clean.
Landscape and portrait modes
The device can be used in landscape and portrait modes. The image rotation for portrait
mode is made on the graphics card.
In portrait mode, the keypad is positioned at the top right and the OSD is not rotated (i.e. the
OSD inscription "Dynamic help for keypad function" is still positioned above the keys).

Setupandinstallation
4.1Installationsite
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 15
4 Setup and installation
CAUTION
Changes to device
Do not make any mechanical or electric changes to the device.
EIZOGmbH is not liable for changes made to the device.
4.1 Installation site
Provide adequate ventilation
Ventilation slots are located on the rear of the housing.
The distance at the rear must be at least 10cm from a wall or 15cm from other devices.
Unimpeded access to the power switch
NOTICE
The power switch and connections must be accessible at all times
When installing and connecting the monitor, ensure that the power switch and the connec-
tions are accessible at all times.
Observe the permissible ambient temperature range
The device must operate within the permissible ambient temperature range.
Desktop installation
If the monitor is installed on a stand, it must be positioned on a hard, horizontal surface.
Avoid reflections on the screen
The monitor has an anti-glare surface which is only effective if the screen is clean and
grease-free.
The SCD 19102 CP and SMD 19102 CP monitors have an optically coated protective glass
pane, which is well suited for use in a germ-free environment when cleaning agents are
used.
If the screen surface is dirty, clean it using a suitable microfiber cloth.
Comply with the specifications for Cleaning [}68].
The monitor should be positioned so that reflections of lights, windows, furniture with shiny
surfaces, or light-colored walls do not appear on the screen.
In order to reduce reflections on the monitor, only use non-dazzling reflector bulbs for the
ceiling lighting.

Setupandinstallation
4.2Installingthemonitor
16 SCD 19102 / SMD 19102 Instructions for Use, 08/2015
Change of environment
If the device is brought into a warm environment from a cold one, condensation may form in
the device. The device should not be switched on until all the condensed water has evapo-
rated, including that inside the device. This may take several hours, depending on the condi-
tions.
4.2 Installing the monitor
Ceiling suspension
Multiple monitors can be installed flush horizontally and vertically to one another.
Comply with the following during installation (100mm hole spacing according to VESA stan-
dard):
Information on the fastening screws
Number 4
Thread M4
Strength 8.8
Insertion depth 7mm minimum / 9mm maximum
Torque Max. 3 Nm
0RXQWLQJSDG6FUHZ0'LVSOD\KRXVLQJPP
Fig.: Insertion depth of mounting screws
See also
Installation site [}15]
Installing the base and cable (SCD 19102) [}22]

Connecting
5.1Generalconnectioninformation
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 17
5 Connecting
5.1 General connection information
CAUTION
All information and warnings related to this product must be observed to ensure danger-
free operation.
CAUTION
Changes to device
Device settings may only be adjusted by trained service personnel; otherwise, the war-
ranty is void.
Do not make any changes to the device without prior approval from the manufacturer.
The monitor is designed for individual connection to a graphics card with a power supply of
110 or 240V (TN-S system with PE conductor).
CAUTION
Observe shielding measures
Please observe all local EMC guidelines pertaining to shielding. If these requirements are
not met, interference signals could penetrate the monitor.
To guarantee perfect image reproduction, the following instructions should be ob-
served:
Only shielded cables are permitted for all signal connections.
Screw tight or lock all plug-in connections.
Signal and power cables must not be routed through the same duct.
The monitor must not share a power supply with motors or valves (interference peaks!).
CAUTION
Excessive currents, short circuits, and ground faults
In accordance with national standards and regulations, protection against excessive cur-
rents, short circuits, and ground faults must be incorporated into the building installation.
NOTICE
Disconnecting from line power
Always set the power switch to "Off" before disconnecting the device from power. Other-
wise the device could be destroyed.

Connecting
5.2Connectorlocation
18 SCD 19102 / SMD 19102 Instructions for Use, 08/2015
5.2 Connector location
The connectors are located in the connection panel behind a cover on the back of the moni-
tor. The power switch is not covered and is freely accessible.
6UHZ&RYHU3RZHUVZLWFK6HUYLFHSLQPLQL',1VRFNHW
Fig.: Rear view of SCD / SMD 19102
5.3 Overview of signals and connections
6&'60''LJLWDO5*%9LGHR$QDORJ&RPSRVLWH[%1&SLQ0LQL',169LGHR'9,
['9,,9*$SLQVXE''9,,6&'$QDORJ5*%[%1&60'6R*+9
Fig.: Overview of signals and connections

Connecting
5.4Connectionpanel
SCD 19102 / SMD 19102
Instructions for Use, 08/2015 19
5.4 Connection panel
A connection panel for the signals and power supply is located on the back of the monitor
SCD19102
'9,/LQHVXSSO\FRQQHFWLRQ3RZHUVZLWFK6HUYLFHPHDVXULQJLQVWUXPHQWV9*$956EXV6HUYLFH'RZQ8S69LGHR&RPSRVLWH
Fig.: Connection panel of the SCD 19102 color monitor
SMD 19102
6HUYLFHPHDVXULQJLQVWUXPHQWV/LQHVXSSO\FRQQHFWLRQ3RZHUVZLWFK69LGHR&RPSRVLWH˖N˖VZLWFKORRSIRU+DQG9'9,9*$956EXV6HUYLFH'RZQ8S6R**9++96R**RXWSXW
Fig.: Connection panel of the SMD 19102 gray scale monitor
See also
Connecting the signal cable [}20]
Connecting the power cable [}21]
Serial interface [}25]

Connecting
5.5Connectingthesignalcable
20 SCD 19102 / SMD 19102 Instructions for Use, 08/2015
5.5 Connecting the signal cable
Note
• The video signals coming from a graphics card are referred to in the following as RGB
signals, and those coming from a camera, DVD player, video recorder etc. as video sig-
nals.
In the OSD menu, some of the menu displays are also identified by RGB or video ac-
cordingly in the header.
• At least one signal source must be connected in order to activate the OSD.
• All signal inputs may be connected simultaneously.
• The Up and Down keys can be used to select which RGB or video source is to be dis-
played when the OSD is not active. Selection is also possible in the OSD.
CAUTION
• When connecting to the BNC sockets, the three cables for the R, G and B signals must
be of equal length. Otherwise, color fringing, which appears similar to convergence
faults, will occur due to unequal propagation times.
• The levels of the incoming analog RGB signals must be equal.
• If the same RGB signal is connected to several monitors via the BNC sockets using T-
connectors, the R, G, B, and H DIP switches on the monitors must be set to 10kΩ. Th-
ese DIP switches must be set to 75Ω on the last monitor in the chain.
The signal cable connections are located on the back of the monitor.
15-pin Sub-D socket
• Connect VGA cable with the 15-pin Sub-D connector (male) for the analog input to the
15-pin Sub-D connector (female).
DVI socket
The DVI cable can be connected in two ways:
• With DVI digital signal or
• With DVI analog signal (SCD 19102 only)
BNC sockets (SoG / H / V)
• With a wire (R or G or B, with composite synchronization):
– Connecting wire for BNC connection "G".
• With three wires (R or G or B, with separate synchronization):
– Connecting wire for BNC connections "G", "H/H+V" and "V".
4-pin mini-DIN socket (video input)
• Connect video cable for the sync video input (Y/C signal) to the 4-pin mini-DIN socket.