Eizo FLEXSCAN L771 - User manual

ENGLISH

2
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please
read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious
injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate
injury and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2000 by EIZO NANAO CORPORATION. All rights reserved. No part of
this manual may be reproduced, stored in a retrieval system, or transmitted, in any form
or by any means, electronic, mechanical, or otherwise, without the prior written
permission of Eizo Nanao Corporation.
Eizo Nanao Corporation is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to Eizo Nanao
Corporation's receipt of said information. Although every effort has been made to ensure
that this manual provides up-to-date information, please note that EIZO monitor
specifications are subject to change without notice.
ENERGY STAR is a U.S. registered mark.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics
Standards Association.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager, PowerManager and i·Sound are trademarks of
Eizo Nanao Corporation.
FlexScan and EIZO are registered trademarks of Eizo Nanao Corporation.
As an ENERGY STAR® Partner, Eizo Nanao Corporation has determined that
this product meets the ENERGY STAR guidelines for energy efficiency.

TABLE OF CONTENTS 3
ENGLISH
TABLE OF CONTENTS
PRECAUTIONS.............................................................................. 4
1. INTRODUCTION .......................................................................... 10
1-1. Features ..................................................................................................... 10
1-2. Package Contents ...................................................................................... 11
1-3. Controls & Connectors ................................................................................ 12
2. CABLE CONNECTION................................................................ 14
2-1. Before connecting ....................................................................................... 14
2-2. Connecting up............................................................................................. 15
3. ScreenManager ........................................................................... 17
3-1. How to use the ScreenManager .................................................................. 17
3-2. ScreenManager Adjustments and Settings ............................................... 18
3-3. Useful Functions......................................................................................... 19
4. ADJUSTMENT ............................................................................ 20
4-1. Screen Adjustment ..................................................................................... 20
4-2. Displaying the low resolutions ..................................................................... 24
4-3. Color adjustment......................................................................................... 26
4-4. Power-save Setup ....................................................................................... 28
5. MAKING USE OF USB (Universal Serial Bus) .......................... 29
6. CONNECTING TWO PCs to THE MONITOR ............................... 31
7. ATTACHING AN ARM STAND .................................................... 33
8. TROUBLESHOOTING ................................................................. 35
9. CLEANING................................................................................... 39
10. SPECIFICATIONS ....................................................................... 40
11. GLOSSARY.................................................................................. 42
12. INDEX .......................................................................................... 44
APPENDIX............................................................................................. i

4PRECAUTIONS
PRECAUTIONS
WARNING
´ If the monitor begins to emit smoke, smells like something is
burning, or makes strange noises, disconnect all power connections
immediately and contact your dealer for advice.
Attempting to use a malfunctioning monitor can be dangerous.
´ Do not dismantle the cabinet or modify the monitor.
Dismantling the cabinet or modifying the monitor may result in electric
shock or burn.
´ Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards.
IMPORTANT!
´This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
´To ensure personal safety and proper maintenance. Please read this section and the
caution statements on the monitor (refer to the figure below).
[Location of the Caution Statements]

PRECAUTIONS 5
ENGLISH
WARNING
´ Keep small objects away from the monitor.
Small objects may accidentally fall through the ventilation slots into the
cabinet, leading to fire, shock, or equipment damage.
´ Keep liquids away from the monitor.
Spillage into the cabinet may result in fire, electric shock, or equipment
damage. If an object or liquid falls/spills into the cabinet, unplug the
monitor immediately. Have the monitor checked by a qualified service
engineer before using it again.
´ Place the monitor on a strong, stable surface.
A monitor placed on an inadequate surface may fall, resulting in injury or
equipment damage. If the monitor falls, disconnect the power immediately
and have the monitor checked by a qualified service engineer before using it
again. Using a monitor after it has been dropped may result in fire or
electric shock.
´ Set the monitor in an appropriate location.
* Do not install in a dusty or humid environment.
* Do not place in a location where steam can have direct contact with
the screen.
* Do not place near heat generating devices or a humidifier.
´ Keep the plastic packing bags away from children and infants.
Plastic bags can be dangerous. To avoid danger of suffocation, keep the
bag away from babies and children.
• Keep power terminal covers for the optional i·Sound™ sound unit
away from children and infants.
Children and infants may accidentally swallow the covers and choke. If
swallowed, consult a doctor immediately.
OK

6PRECAUTIONS
OK
WARNING
• Use the enclosed power cord. If using the power cord other than the
enclosed one, follow these guidelines.
[USA and Canada]
Use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting
the following specifications.
* Rating: min. 125 V, 10 A *Length: max. 2.0 m
* Plug type: NEMA 5-15P, Parallel blade, Grounding type, 125 V, 10 A
* Type: SVT
[Europe]
Use a proper European standard approved power cord meeting the
following specifications.
* Rating: min. 250 V, 10 A *Length: max. 2.0 m
* Type: H05VV-F 3G 1 mm2
Use a plug type approved by the country where you reside. Failure to do so
may cause fire or electric shock.
´ To disconnect the power cord, grasp the plug firmly and pull.
Never tug on the cord, doing so may cause damage and couldresult in
fire or electric shock.
´ The equipment must be connected to a grounded main outlet.
´ Use the correct voltage.
* The monitor is designed for use with a specific voltage only. Connection
to a different voltage may cause fire, electric shock, or other damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
* For proper connections of the power cord, be certain to plug the
power cord to the provided monitor connector and directly to a wall
outlet. Not doing so may result in fire or electric shock.
´ Handle the power cord with care.
* Do not place the cord underneath the monitor or other heavy objects.
* Do not pull on the cord.
* Do not attempt to repair a damaged cord.
If the power cord becomes damaged, stop using it. Use of a damaged
cord may result in fire or electric shock.
´ Never touch the plug and power cord if it begins to thunder.
If it begins to thunder, do not touch the plug, power cord or cable.
Touching them may result in electric shock.

PRECAUTIONS 7
ENGLISH
WARNING
´ Install the monitor securely when attaching to an arm stand.
When attaching an arm stand, please refer to the user’s manual of the arm
stand and install the monitor securely with the enclosed screws. Not doing
so may cause the monitor to come unattached, which may result in injury
or equipment damage. When the monitor is dropped, please ask your
dealer for advice. Do not continue using a damaged monitor. Using a
damaged monitor may result in fire or electric shock.
When reattaching the tilt stand, please use the same screws and tighten
them securely.
´Do not touch a damaged LCD panel directly with bare hands.
Use protective gloves whenever handling a damaged panel. The liquid
crystal which leaks from the panel is poisonous if it enters the eyes or
mouth. If any part of the skin or body comes in direct contact with the
panel, please wash thoroughly. If some physical symptoms result, please
consult your doctor.
´ Take care when disposing of the monitor.
The backlight of the LCD panel contains mercury. Follow local
regulation or laws for safe disposal.
CAUTION
• Handle with care when carrying the monitor.
* Disconnect the power cord, signal cables and remove the optional
i·Sound™sound unit (if applicable). Moving the monitor with the cord
attached or lifting it by the i·Sound™sound unit is dangerous. It may
result in injury or equipment damage.
* When handling the monitor, grip the bottom of the monitor firmly with
both hands ensuring the panel faces outward before lifting.
* Handle with care to avoid scratching or damaging the panel. If the
monitor becomes damaged, disconnect the power immediately and have
the monitor checked by a qualified service engineer before using it again.
Using a monitor after it has been dropped may result in fire or electric
shock.
OK

8PRECAUTIONS
CAUTION
´ Do not block the ventilation slots on the cabinet.
* Do not place books or any other papers on the ventilation slots.
* Do not install the monitor in a closed space.
* Do not use the monitor lengthwise or upside down.
Using the monitor in this way blocks the ventilation slots and prevents
proper airflow, leading to fire or other damage.
• Do not use the LCD monitor outdoors or inside a car.
This LCD monitor has been made specifically for indoor use as a desktop
monitor. Using it anywhere else may result in fire, electrical shock, or
other damage.
• When adjusting the viewing angle of the monitor, do not do so by
handling i·Sound™ sound unit (if applicable).
Adjusting the monitor in this way may break the monitor or cause bodily
injury.
´ At the end of the day or if you plan to leave the monitor unused for an
extended period after turning off the power switch, disconnect the
power cord from the wall socket so that no power connections are
made.
´ Do not touch the plug with wet hands.
Touching the plug with wet hands is dangerous and can cause electrical
shock.
´ Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
´ Unplug the monitor before cleaning it.
Cleaning the monitor while it is plugged into a power outlet may result in
electric shock.
´ Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl
alcohol), abrasive cleaners, or other strong solvents, as these may
cause damage to the cabinet or LCD panel.
´ Periodically clean the area around the plug.
Buildup of dust, water, or oil on the plug may result in fire.

PRECAUTIONS 9
ENGLISH
Suggestions for Maximizing Comfort
´ To lessen the chance of possible injury and to increase your
comfort and productivity while you operate the monitor, we suggest
the following:
* Avoid less favorable body positioning. Sit back on the chair with
your back straight.
* Adjust the height of the chair so that the both soles touch the floor.
* Adjust the height of your chair, monitor, or keyboard so that you
can keep your wrists straight while typing.
* Set the terminal slightly below eye level.
´ Adjust brightness of the screen depending on the brightness of
your environment. Too dark or too bright of a screen can cause eye
strain.
´ Be sure to take adequate rests. A 10-minute rest period each hour
is suggested.
• Do not remove the covers to the power terminal for the optional
i·Sound™ sound unit for any reason except to attach the monitor.
LCD Panel
´ The screen may have defective pixels. These pixels may appear as
slightly light or dark area on the screen. This is due to the
characteristics of the panel itself, and not the product.
´ The backlight of the LCD panel has a fixed life span.
When the screen becomes dark or begins to flicker, please contact your
dealer.
´ Do not press on the panel or edge of the frame strongly, as this will
result in damage to the screen. There will be prints left on the
screen if the pressed image is dark or black. If pressure is
repeatedly applied to the screen, it may deteriorate or damage your
LCD panel. Leave the screen white to decrease the prints.
´ Do not scratch or press on the panel with any sharp objects, such
as a pencil or pen as this may result in damage to the panel. Do not
attempt to brush with tissues as this may scratch the LCD panel.

10 1. INTRODUCTION
1. INTRODUCTION
Thank you very much for choosing an EIZO Color LCD Monitor.
1-1. Features
•Dual inputs compliant (D-Sub mini 15 pin x 2)
•1600 x 1200 resolution
Horizontal scanning frequency of 27-94 kHz
Vertical scanning frequency of 50-85 Hz (1600 x 1200 ~75Hz)
•Auto Adjustment compliant and original “Picture Adjustment Program”software
included
•Smoothing function incorporated for the adjustment of an enlarged image
•ColorManagement function incorporated
•USB (Universal Serial Bus) hub supported

1. INTRODUCTION 11
ENGLISH
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
•LCD Monitor •Signal Cable (MD-C87/C100)
•Power Cord •Connector Cover
•4 of 4 mm x 12 mm mounting screws •Rear Cover (attached to the monitor)
•EIZO LCD Utility Disk •User’s Manual
•Quick Reference •Warranty Registration Card
•Please retain the packing materials for future transference.

12 1. INTRODUCTION
(2) (3)
(4)
(5) (6)(7) (8)
(1)
1-3. Controls & Connectors
Front
(1) ScreenManager™
(2) PowerTerminal Covers for the Optional peripheral
(3) Input Signal Selection Button
(4) Auto Adjustment Button
(5) Enter Button
(6) Control Buttons
(7) Power Button
(8) Power Indicator*1
Indicated color Power-on status
Green Power is on
Yellow Power save mode
Slowly flashingYellow Power is off (Main power is on)
*1 Regarding the power indicator for the “Off Timer”, see page 19.

1. INTRODUCTION 13
ENGLISH
( 9) (10) (12) (13) (14) (15) (16)(11)
Rear
(9) Main Power Switch
(10) 4 Holes for Mounting an Arm-Stand*2
(11) Stand (Detachable)*2
(12) USB Downstream Ports x 4
(13) Power Connector
(14) Security Lock Slot*3
(15) D-Sub mini 15 pin Input Connector x 2
(16) USB Upstream Port x 1
*2 The LCD monitor can be used with an optional arm stand by removing the stand
(see page 33).
*3 Allows for connection of a security cable. This lock supports Kensington’s MicroSaver
security system. For further information, please consult:
Kensington Technology Group 2855 Campus Drive, San Mateo, CA 94403 USA
800-650-4242, x3348
Intl: 650-572-2700, x3348 / Fax: [phone]
http://www.kensington.com

14 2. CABLE CONNECTION
2. CABLE CONNECTION
2-1. Before connecting
Before connecting your monitor to the PC, change the display screen settings (resolution
p. 43) and frequency) in accordance with the charts below.
•About Plug & Play of the monitor
When your computer and display support VESA DDC, the suitable resolution and the
refresh rate are set by just plugging your display into the computer without any
manual settings.
When your computer system supports Plug & Play, the Display Information File is
not required except for installing the Color Profile.
noituloseR ycneuqerF skrameR
084x046zH58~ASEV,AGV
004x027zH07txeTAGV
006x008zH58~ASEV
426x238zH57hsotnicaMelppA
867x4201zH57~ASEV
078x2511zH57hsotnicaMelppA
009x2511zH67~SWNUS
069x0821zH58~hsotnicaMelppA
4201x0821zH58~ASEV
0021x0061zH57~ASEV

2. CABLE CONNECTION 15
ENGLISH
2-2. Connecting the signal cable
• Be sure that the power switches of both the PC and the monitor are OFF.
1. Remove the rear cover from the monitor.
When removing the rear cover, push down the buttons while pulling.
2. Plug the signal cable into the D-Sub connector at the rear of the
monitor and the other end of the cable into the video connector on the
PC.
After connecting, secure the connection with the screw-in fasteners.
buttons
Signal Cable (enclosed)
Power cord
Macintosh Adapter (Optional)
Video Output Connector
D-Sub mini 15 pin
·Standard graphics board
·Macintosh G3 (Blue & White) / G4
Macintosh
Video Output Connector
D-Sub 15 pin

16 2. CABLE CONNECTION
3. Plug the power cord into the power connector on the rear of the
monitor.
WARNING
•Use the enclosed power cord. If using the power cord
other than the enclosed one, follow these guidelines.
[USA and Canada]
Use a UL LISTED/CSA LABELED or CERTIFIED power cord
set meeting the following specifications:
* Rating: min. 125 V, 10 A
* Length: max.2.0 m
* Type: SVT
* Plug type: NEMA 5-15P, Parallel blade,
Grounding type, 125 V, 10 A
[Europe]
Use a proper European standard approved power cord
meeting the following specifications:
* Rating: min. 250 V, 10 A
* Length: max.2.0 m
* Type: H05VV-F 3G 1 mm2
Use a plug type approved by the country where you reside.
Failure to do so may cause fire or electric shock.
4. Replacing the connector cover and the rear cover.
1) Insert the rear cover into the inlets at the bottom of the stand.
2) For smooth attachment, the monitor should be tilted forward. Attach the
connector cover to the rear panel of the monitor.
5. Plug the other end of the power cord into a power outlet.
WARNING
•The equipment must be connected to a grounded main
outlet.
6. Turn on the monitor’s main power and then switch on the PC’s power.
Whenever finished, turn off the PC and the monitor.
21

3. ScreenManager 17
ENGLISH
3-1. How to use the ScreenManager
As shown on the display, the ScreenManager is used to adjust the LCD monitor.
ScreenManager consists of main menus and sub menus. Adjustments are made using the
Enter and Control buttons (up, down, right and left) located on the front panel.
1. Entering the ScreenManager
Push the Enter button once to display the main menu of the ScreenManager.
2. Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control buttons and push the Enter
button. The sub menu appears.
(2) Use the Control buttons to select the desired setting icon and push the Enter
button. The setting menu appears.
(3) Use the Control buttons to make all required adjustments and push the Enter
button to save the settings.
3. Exiting the ScreenManager
(1) To return to the main menu, select the “Return”icon or push the down button
twice, followed by the Enter button.
(2) To exit the ScreenManager, select “Exit”icon and push the Enter button.
Enter Button
Control Buttons
Auto Adjustment Button
3. ScreenManager
[ Main Menu ]

18 3. ScreenManager
3-2. ScreenManager Adjustments and Settings
The following table shows all the ScreenManager’s adjustment and setting menus.
Main menu Sub menu Reference
Screen Clock
Phase
Position
Resolution
Smoothing
Contrast
Brightness
ColorManagement RangeAdjustment
Standard mode
·Temperature
Custom mode
·Temperature
·Saturation
·Hue
·Gain
·Save
PowerManager VESA DPMS
EIZO MPMS
Others ScreenSize
Border Intensity
Input Priority Select the priority input signal. (p.32)
Off Timer Set the monitor’s off timer to on or off. (p.19)
Beep Set the Monitor’s beeper to on or off. (p.41)
Menu Position Adjust the ScreenManager’s menu position.
Reset Return to the factory default settings. (p.41)
Information Information Review the current ScreenManager’s settings.
Language Select the ScreenManager’s language.
4. ADJUSTMENT(p.20)
•Double clicking the Enter button at any time also exits the ScreenManager menu.
•Leaving the ScreenManager idle for 45 seconds or more will turn the adjustment off
automatically, without saving the adjustments.
English, German,
French
Spanish, Italian,
Swedish and
Japanese

3. ScreenManager 19
ENGLISH
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock”function to prevent any accidental changes.
Locked function •Auto adjustment button adjustments and settings in the
ScreenManager.
Unlocked function •Adjustment of contrast and brightness by the control buttons.
•Input signal selection button
•To lock
Press on the Auto adjustment button while switching on the monitor’s power button
on the front panel.
•To unlock
Switch off the monitor’s power button on the front panel, then hold down the Auto
adjustment button once again and turn the power back on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state after a
predetermined amount of time has lapsed. This function was created to reduce
afterimagep.42) characteristics that are particular to LCD monitors when the monitor
screen is left on for a long period without use.
[Procedure]
(1) Select “Off Timer”in the ScreenManager “Others”menu.
(2) Select “Enable”and press the right and left buttons to adjust the “On Period”
(1 to 23 hours).
[Off timer system]
*1Advance notice (LED flashing green) will be given 15 minutes before the monitor
automatically enters the “Power Off”mode. To delay entering the “Power Off”mode,
press the power button during the advance notice period. The monitor will continue to
operate for an additional 90 minutes.
Press the power button to return to a normal screen.
•The off timer function works while the PowerManager is active, but there is no
advance notice before the monitor’s power is switched off.
CP rotinoM DEL
)H32~H1(doirePnOnoitarepOneerG
"doirepnO"ni.nim51tsaL ecitoNecnavdA
1*
)speeBhtiw( gnihsalFneerG
deripxe"doirepnO"edoM"ffOrewoP"ylwolswolleygnihsalF

20 4. ADJUSTMENT
4. ADJUSTMENT
4-1. Screen Adjustment
Screen adjustments for the LCD monitor should be used in suppressing screen flickering
and also for adjusting the screen to its proper position. There is only one correct position
for each display mode. It is also recommended to use the ScreenManager function when
first installing the display or whenever changing the system. For convenience, an easy
set-up Program installed on the utility disk to assist in the set-up procedure is provided.
Adjustment Procedure
•Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments.
1. Push the Auto adjustment button on the front panel.
The message “Your setting will be lost, if you press again now.”appears and
remains on the screen for 5 seconds. While the message is on the screen, push the
Auto adjustment button again to automatically adjust the clock, phase, screen
position and resolution. If you do not wish to do adjust the screen, do not push the
Auto adjustment button again.
If the appropriate screen can not be made by using the Auto adjustment button,
adjust the screen through the following procedures.
2. Install the “Screen adjustment program”.
Having read the “readme.txt”file, install and run the “Screen adjustment program”
in the enclosed EIZO LCD utility disk.
Step by step adjustment is provided by the wizard guide.
•If the user’s operating system has no utility disk (e.g. OS/2), we recommend
setting the desktop pattern to that as shown in the diagram below.
Every-other-dot
pattern