EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB User manual

USER GUIDE
MONOBLOCK
EK-Quantum
Momentum2VRM Bridge ROG Maximus Z790 Formula D-RGB - White

- 2 -
This product is intended for installation only by expert users. Please
consult with a qualified technician for installation. Improper installation
may result in damage to your equipment. EK Water Blocks assumes no
liability whatsoever, expressed or implied, for the use of these products,
nor their installation. The following instructions are subject to change
without notice. Please visit our website at www. ekwb.com for updates.
Before installation of this product please read the important notice,
disclosure, and warranty conditions printed on the back of the box.
Before you start using this product, please follow these basic guidelines:
Please carefully read the manual before beginning the
installation process!
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
The use of corrosion inhibiting coolants is always recommended
for liquid cooling systems and mandatory for nickel-plated
water blocks!
Do not use pure distilled water! For best results, EK recommends
the use of EK-CryoFuel coolants!
Make sure to thoroughly bleed air out of your water block, or
you will not achieve optimal performance!

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
WATER BLOCK SPECIFICATIONS AND MAIN PARTS 6
INSTALLING AND ATTACHING THE WATER BLOCK 7
SUPPORT AND SERVICE 11
SOCIAL MEDIA 11

- 4 -
BOX CONTENTS
Allen Key 2.5 mm (1 pc) Grease (1 pc)
Extender M12F (2 pcs) VRM Bridge Extender (2 pcs)
Mounting Mechanism
EK-Loop Multi Allen Key (1 pc)
EK-Quantum Momentum2VRM Bridge ROG Maximus Z790
Formula D-RGB - White

- 5 -
WATER BLOCK DIMENSIONS
64.7 mm
135 mm
18.1 mm
36.6 mm
128 mm
71.5 mm

- 6 -
WATER BLOCK SPECIFICATIONS AND MAIN PARTS
Technical Specification:
- Dimensions: (LxHxW) - 128 x 135 x 18.1mm
- D-RGB cable length: 500mm
- D-RGB LED count: 19
- D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)
Position EAN Description Quantity
1105115 Metal plate 1
2107197 Acetal Standout (White) 1
3105118 Bottom plate (Plexi) 1
4105117 Top plate (Plexi) 1
5100947
Screw M3x6 ISO 7380 3
6100663 EK - Badge 1
7107196 Mylar sticker (White) 1
8105166 O-Ring set 1
9104353 Screw M3x12 7991DIN 13
10 105120 Acetal Standoff 3
11 8603 Metal washer M4 3
12 8011 Screw M4x10 ISO 7380 3
13 104988 Screw M4x18 7991DIN 1
14 103155 LED D-RGB Dense Strip - 500/130mm 1
12
2
1
7
6
13
8
11
10
9
4
3
14
5

- 7 -
STEP 2
Unscrew the one (1) M4 x 18 DIN7991 screw using the enclosed
2.5mm Allen key and remove it from the block.
Save the screw for later step.
STEP 2
STEP 1
Install your EK-Quantum Velocity21700 water block in the illustrated
orientation and place the motherboard on a secure flat surface. Using
the enclosed EK-Loop Multi Key, install two (2) Extenders M12F and
two (2) torque push-in fixation fittings to the pre-installed VRM block
and CPU block (as shown in the image).
Do not use excessive force while tightening the fittings.
EXTENDER
M12F
STEP 1
PUSH-IN
FITTING
M4 x 18 DIN7991 SCREW
INSTALLING AND ATTACHING THE WATER BLOCK
For this step, you will need:
EK-Loop Multi Allen Key
For this step, you will need:
Allen Key 2.5mm

- 8 -
STEP 4
Before attempting to mount the water block, apply a small amount
of the supplied grease to each of the four (4) O-Rings on the fixation
fittings. Next, position the water block over the fixation fittings and
force it into place evenly.
STEP 4
STEP 3
Slide the Plexi away from the black acetal stand-out with stainless
steel fixation plate until it stops (approximately at 3 mm)
STEP 3
STANDOUT
(BLACK ACETAL)
PLEXI PLATE
O-RING
3 mm GAP
For this step, you will need:
Grease

- 9 -
STEP 6
With the EK-Quantum Momentum2VRM Bridge ROG Maximus
Z790 Formula D-RGB - White water block, it is mandatory to use
the bottom port as the INLET. Mixing the ports may result in poor
thermal performance of the water block.
Tighten the fittings in a clockwise direction until the gasket
underneath is compressed. The installation of the water block is
now complete.
STEP 6
STEP 5
Push the plexi plate back to its original position and screw back the
one (1) M4 x 18 DIN7991 screw that was removed in Step 2.
Do not use excessive force while tightening the screw!
STEP 5
ALLEN KEY M2.5
OUTLET
INLET
For this step, you will need:
Allen Key 2.5mm
PLEXI PLATE
M4 x 18 DIN7991
SCREW

- 10 -
STEP 7
Plug the 3-pin D-RGB connector from the bridge block in a D-RGB
header on your motherboard or controller. The LED strip will only
work if the pin layout on the header is as follows: +5V, Digital,
Empty, Ground.
Incorrect installation or installation of the incorrect header
could result in damage to the LED strip or the header itself.
D-RGB Header
RGB Header
STEP 7

In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND WATER BLOCK PARTS” where you can find
the EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA