iWave iW-RainboW-G47D User manual

[email protected] www.iwavesystems.com
Virtex UltraScale+ FPGA SOM
Development Platform
iW-RainboW-G47D
Quick Start Guide

Disclaimer
iWave Systems reserves the right to change details in this
publication including but not limited to any Product specification
without notice.
No warranty of accuracy is given concerning the contents of the
information contained in this publication. To the extent
permitted by law no liability (including liability to any person by
reason of negligence) will be accepted by iWave Systems, its
subsidiaries or employees for any direct or indirect loss or
damage caused by omissions from or inaccuracies in this
document.
Trademarks
Certification
iWave Systems Technologies Pvt. Ltd. is an ISO 9001:2015
Certified Company.
All registered trademarks, product names mentioned in this
publication are the property of their respective owners and used
for identification purposes only.

Introduction
Quick Start Guide (QSG)
This Quick Start Guide (QSG) is designed for users to quickly
understand the iW-RainboW-G47D-Virtex UltraScale+ FPGA
SOM Development Platform and start the evaluation. It
provides the instructions for setting-up the Development
Platform from the packed box.
Development Platform Description
g Virtex US+ FPGA SoC with 3780K Logic Cells
The iW-RainboW-G47D Virtex UltraScale+ FPGA SOM
Development platform incorporates with iWave's Virtex
UltraScale+ FPGA based SOM and Ultra High Performance
carrier board with all necessary interface connectors for
developing an embedded application based on Xilinx Virtex
UltraScale+ FPGA.
Some Key Features of the Board Include:
g Dual 4GB PL DDR4 for FPGA
g 256MB NOR Flash (CPU)
g USB 3.0 Type-C & USB 2.0 OTG Port.
g Layerscape (LS1021A) CPU with dual-core Cortex-A7
g PCIe x1 Port.
g Gigabit Ethernet RJ45 Magjack
g QSFP+ and SFP+ Connectors
g HDMI IN/OUT
g SDI IN/OUT
g 128MB QSPI Flash (FPGA)
Quick Start Guide
01
g 2GB DDR4 for CPU
g 12 Pin PMOD Connectors
g Firefly Connector
g FMC+ and FMC HPC Connectors

This development platform is ESD
sensitive. Handle the product only in
accordance with the installation
instructions given in the manual.
Therefore ESD precautions should be
taken care during transport and
handling.
Safety
iW-RainboW-G47D-Virtex UltraScale+
FPGA SOM Development Platform is
designed by using RoHS and REACH
c o m p l i a n t c o m p o n e n t s a n d
manufactured on lead free production
process.
Check the local regulations for
disposal of electronic products before
disposing.
ESD Protection
Product Disposal
Environmental Compliance
Must use a ESD ground strap or other
grounded source before unpacking or
handling the hardware.
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G47D
02

Quick Start Guide
Step 1 - Unpacking
Remove the Development platform from anti-static cover and
place it above the ESD free area. Use anti-static pad/mat with
proper grounding to place the Development Platform. Don't
touch inside surface of the circuit board.
iW-RainboW-G28D
Quick Start Steps
Avoid using board in extreme dust, humidity and temperature
conditions. Also this development platform is not water proof.
Keep away from wet surface.
Package Box
Quick Start Guide
iW-RainboW-G28D
Quick Start Guide
03

Make sure that, below deliverables are received without any
physical damage.
12V,14A Power Supply USB OTG Cable
Development Platform
Step 2 - What's Inside The Box ?
04
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G47D
JTAG Cable

Step 3 - Download FTP Contents
iW-RainboW-G30D
Hardware
Datasheet
PCB-CAD Files
QuickStartGuide
SOM-Datasheet
DevKit-Datasheet
SOM
DevKit
FPGA-Example-Design
Binaries
Tools
FPGAUserGuide
ReleaseNotes
SoftwareUserGuide
Source Code
Integrated Design
IBERT Design
Fansink-Datasheet
PCB-CAD Files
Mechanical Files
Compliance Report
FPGA Name
SOM Part Number
Vivado Version
Documents
Software+FPGA
Hardware
iW-RainboW-G47D
All the technical resources of iW-RainboW-G47D Virtex
UltraScale+ FPGA SOM Development platform is available in
iWave FTP server.
For FTP Credentials, Contact : [email protected]
FTP Folder Structure
Quick Start Guide
05
PCB-CAD Files
B2B-ConnectorPinout

Step 4 - Read Documents
Before moving to next step, one must go through all the
documents including Hardware Datasheets and get familiar
about iW-RainboW-G47D Virtex UltraScale+ FPGA SOM
Development platform.
Development Platform Documents:
■ Quick Start Guide (This document)
■ SOM Datasheet
■ DevKit Datasheet
■ Release Notes
■ Software User Guide
■ FPGA User Guide
06
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G47D

Step 5 -Quick View-SOM
TOP View
BOTTOM View
1. Virtex UltraScale+ FPGA SoC
2. PMIC Programming Header
3. LS1021A Layerscape CPU
4. Board to Board connector 1
5. Board to Board connector 2
6. Board to Board connector 3
7. Board to Board connector 4
1
2
3
Quick Start Guide
07
67
54

01. FireFly Connector
02. FireFly Power Connector
03. JTAG Connector
04. PMOD Connector 2
05. Reset Switch
06. PMOD Connector 1
07. Board to Board Connector4
08. Power ON/OFF Switch
09. Power Connector
10. Debug UART Connector
11. 20 Pin GPIO Header
12. USB 2.0 OTG Connector
13. Gigabit Ethernet MagJack
14. PCIex1 Connector
15. Board to Board Connector 2
16. Board to Board Connector 1
17. FMC Connector
18. FMC+ Connector
19. Board to Board Connector 3
20. 12V Fan Header
21. QSFP+ Connector
22. RTC Battery Holder
23. SDI IN/OUT
24. HDMI IN/OUT
25. SFP+ Connector
26. USB 3.0 Type-C Connector
Step 6 - Quick View-Carrier Board
TOP View
BOTTOM View
1 2 3 4 5 6 7
20
8
9
10
12
14
11
1516
17
18
19
13
21
22
08
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G47D
Note : Connectors which are not highlighted is not supported by the Virtex
UltraScale+ FPGA Development Kit
23
24
25
13
26

Install the driver for Debug Port in Host PC/Laptop using the
below link.
https://ftdichip.com/products/ft232rq/
Connect TypeA end of USB cable to PC and MicroB end of USB
cable to Development platform's Debug USB MicroAB
Connector (J13) as shown below.
Step 7 - Debug Port Setting
Setup the Debug Terminal parameters.
Baud Rate : 115200
Data bits : 8
Parity : None
Stop Bits : 1
Flow Control : None
Quick Start Guide
09

Step 8 - Power-ON the Development Platform
Connect the 12V power supply plug to the power connector
(J10) of the Development platform as shown below and switch
ON the power supply.
Warning :
1. Do not try to connect any other power supply other than supplied along
with the Development platform.
2. Do not plug or remove the Virtex UltraScale+ FPGA SOM from carrier board
with live power.
3. Contact iWave if any LEDs are not glowing
Once power is applied to the Development platform, the power
LEDs in Virtex UltraScale+ FPGA SOM and Ultra High Speed
Carrier Board will glow as shown in the below image.
SOM Power LED
Carrier Board Power LED
FPGA Program Done LED
10
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G47D

Debug Terminal
Step 9 - Test Environment setup
Once power is applied to the Development Platform as
explained in the previous section, boot messages being
displayed in the debug terminal of the PC/Laptop which is
connected to the Development platform. Press any key in
terminal immediately to see the command prompt of the Boot
loader or wait until OS boots.
After OS boots, Login prompt being displayed in the debug
terminal.
Quick Start Guide
11

Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G35D
iW-RainboW-G47D Virtex UltraScale+ FPGA SOM Development
platform comes with Heat Sink + Fan mounted on SOM.
Makesure to power up the platform only with Heatsink+Fan
attached.
Heatsink + Fan Peel off Thermal pad sticker
Below is the Heatsink+Fan integration procedure for
reference.
Connect the Fan cable
to SOM Fan Header
Fix the heatsink in to SOM
Heat Sink
Heat Sink Integration
12
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G47D

iW-RainboW-G47D Virtex UltraScale+ FPGA SOM Development
platform Support JTAG interface in Carrier Board for FPGA and
CPU Programming.
In the carrier board Config Switch (SW6.2) is provided for
selecting the JTAG device between FPGA and CPU.
JTAG
JTAG Connection
Quick Start Guide
13
FPGA as JTAG Device CPU as JTAG Device

Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G47D
14
FPGA JTAG Connection to Carrier Board :
JTAG-HS2 Programming Cable
Part Number: 410-249 from Digilent
Example JTAG Cable which is tested with this Platform is
mentioned below.
After changing Config switch and selecting the JTAG device as
FPGA, Power on the board connect the JTAG cable to the carrier
board as shown below.

Quick Start Guide
15
CPU JTAG Connection to Carrier Board :
https://www.nxp.com/design/software/development-
software/codewarrior-development-tools/run-control-
devices/codewarrior-tap:CW_TAP
For further details regarding CodeWarrior® TAP, visit the below
link:
After changing Config switch and selecting the JTAG device as
CPU, connect the CodeWarrior® TAP to carrier board via
custom made JTAG cable provided from iWave.
Connect the CodeWarrior® TAP to the PC through USB and
Power on the board.
Pin No. 1
Pin No. 1

iWave’s Other Products
Product Name: Zynq US+ MPSoC
(4/5/7-EV/EG/CG) SOM
Processor: Xilinx’s Zynq US+ MPSoC
(4/5/7-EV/EG/CG)
RAM: 4GB PS DDR4*
1GB PL DDR4*
Application: Industrial Motor Control &
IoT, Sensor Fusion, ADAS/Embedded
Vision, Data Center, Medical Endoscopy
* RAM size is expandable. Contact iWave team for further details
Product Name: Zynq UltraScale+ MPSoC
(ZU5/ZU4/ZU3/ZU2) SBC
Processor: Xilinx’s Zynq US+ MPSoC
(2/3/4/5-EV/EG/CG)
RAM: 8GB PS DDR4* & 4GB PL DDR4*
Application: AI/ML, Industrial IoT, Human
Machine Interface, Advanced Driver
Assistance Systems.
Product Name: Zynq US+ MPSoC
(11/17/19-EG) SOM
Processor: Xilinx’s Zynq US+ MPSoC
(11/17/19-EG)
RAM: 4GB PS DDR4*
4GB Dual PL DDR4*
Application: Video Surveillance, Cloud
Computing, Artificial Intelligence/Machine
Learning, 5G Wireless, High Precision Test
Instrument.
16
Quick Start Guide
iW-RainboW-G28D
iW-RaniboW-G28D
iW-RainboW-G28DiW-RainboW-G28D
iW-RainboW-G47D

13
Need More Help ?
iWave Systems Provides Technical Support to all Customers
Worldwide.
gEmail
Write your technical queries to [email protected]
gPhone
Call us on : [phone], 26781643, 26786245
gLive Chat
We provide Live Chat technical support to our customers.
Contact iWave to enable Live Chat support.
iW-PRHBZ-UM-01-R2.x-REL0.1-QSG
Warranty support for Hardware: 1 Year from iWave or iWave's
EMS partner.
Warranty & RMA
03
For Return Merchandise Authorization
(RMA),scan the QR code or go to :
https://www.iwavesystems.com/support/rma/
For Warranty terms & Registration, scan
the QR code or go to :
https://www.iwavesystems.com/support/
warranty/
Quick Start Guide
17

USA
JAPAN
iWave Japan, Inc.
8F-B, Kannai Sumiyoshi Building,
3-29, Sumiyoshi-cho, Naka-ku, Yokohama,
Kanagawa, Japan.
Email: [email protected]
Ph: [phone], 26781643
Israel
Value Technologies Ltd.
P.O. BOX 3161, Tel-Mond, Israel
4060000
Tel: [phone]
Fax: [phone]
Email: [email protected]
FRANCE
EUROPE
iWave Europe.
International Sales and Marketing,
Europe.
Venkelbaan 55 2908KE Capelle
aan den Ijssel
Email: [email protected] Our Partners
Across The Globe
POLAND KOREA
J.S Communications
913, Dojung Tower, Anyang-ro 115,
Manan-gu, Anyang-si, Gyeonggi-do, Korea
Tel : [phone]
Email: [email protected]
Headquarters: INDIA
iWave Systems Tech. Pvt. Ltd.
7/B, 29th Main, BTM Layout 2nd Stage,
Bengaluru-560076,India.
Ph: [phone], 26781643
Email: [email protected]
www.iwavesystems.com
FRANCE
EUROCOMPOSANT
1, rue René Caudron - BP 15
78960 Voisins-le-Bretonneux,
France
Tel: [phone]
Fax: [phone]
Email: [email protected]
ME Embedded Sp. z o.o.
Staniewicka 14 street,
03-310 Warsaw, Poland.
Tel: [phone]
Email: [email protected]
SWEDEN
Acte Solutions AB
Box 4115,
SE-171 04 Solna,
Sweden.
Tel: [phone] / 46
Email: [email protected]
GLOBAL
Arrow Electronics, Inc.
9201 East Dry Creek Road
Centennial, CO 80112 USA
NA: [phone]
[email protected]
EMEA: [phone]
[email protected]
Asia: [phone]
[email protected]
GLOBAL
Future Electronics
237 Hymus Blvd.,
Pointe Claire, Quebec,
Canada H9R 5C7.
Tel: [phone]
Email: [email protected]
EMEA: [phone]
[email protected]
Asia: [email protected]
GLOBAL
Mouser Electronics, Inc.
1000 North Main Street
Mansfield, Texas 76063
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
TURKEY
ÖZDİSAN ELEKTRONİK A.Ş.
DES Sanayi Sitesi 104 Sokak A07,
54-56 Upper Dudullu / Ümraniye,
Istanbul - Turkey
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
UNITED STATES
iWave USA
1692 Westmont Ave., Campbell,
CA95008 USA
Ph: 408-206-5958
Email: [email protected]
Batenburg Applied Technologies
Stolwiikstraat 33, 3079 DN
Rotterdam.
Tel: [phone],
[phone]
Email: [email protected], .be
BENELUXONLINE
Digi-Key Corporation
701 Brooks Avenue South
Thief River Falls,
MN 56701-0677
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
Embedded Technologies, Inc
2870 Scott St, Suite 101,
Vista, California, USA,
Tel:[phone],
E-mail: [email protected]
SPAIN
Anatronic
Paseo de los Melancólicos, N° 9-2° A
28005 MADRID, Spain
Tel : [phone]
Email: [email protected]