EK-Quantum Reflection PC-O11D Mini D5 PWM D-RGB User manual

USER GUIDE
DISTRIBUTION PLATE
EKQuantum
Reflection2PC-O11D Mini D5 PWM D-RGB

Please note the installation of the product is intended to be
undertaken by an adequately trained and experienced person.
You are installing the product at your own risk. If you are not
properly trained or experienced or feel unsure about the
installation procedure, please refrain from installing the product
yourself and contact our tech support for assistance. We disclaim
our liability for any damages to the product as well as incidental,
consequential, or indirect damages incurred due to improper or
inappropriate installation.
Before you start using this product please follow these basic guidelines:
Please carefully read the manual before beginning with the
installation process!
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting coolants
is always strongly recommended for any liquid cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
DISTRIBUTION PLATE DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6
PREPARING THE O11D Mini CHASSIS 7
INSTALLING THE DISTRIBUTION PLATE 8
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS 9
7SLOT CONFIGURATION 9
5SLOT CONFIGURATION 11
FLOW DIAGRAM 13
CONNECTING THE D-RGB LED STRIP 14
CONNECTING THE PUMP 14
TESTING THE LOOP 15
SUPPORT AND SERVICE 16
SOCIAL MEDIA 16

- 4 -
BOX CONTENTS
8
EK-Quantum Reflection2PC-O11D Mini D5 PWM D-RGB
M4 x 8 7991DIN (8 pcs)
Allen Key 2.5 mm (1 pc)
EK-Loop Multi Allen Key

- 5 -
DISTRIBUTION PLATE DIMENSIONS
206 mm
332 mm
302.5 mm
189.5 mm
230.5 mm
8 mm
76 mm
30.5 mm

- 6 -
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
Technical Specification:
Dimensions with the attached pump (H x W x D): 332 x 206 x 76 mm
– D-RGB LED count: 12
– D-RGB cable length: 500 mm
– D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)
Position EAN Description Quantity
1105063 Bottom plexi plate 1
2105064 Top plexi plate 1
3105067 LED Cover (Black e.) 1
4100663 EK - Badge 1
55154 OR 52 x 3 mm 1
63831109837597 D5 Pump 1
7101803 Pump cover (Acetal) 1
88311
Screw M4 x 20 DIN7984 4
98312
Screw M4 x 16 DIN7991 49
10 104642 Left Mount (Black E.) 1
11 9061 Screw M3 x 25 DIN7991 6
12 104599 Mylar - Reflection2 2
13 102639 EK - Plug G1/4 10
14 SET OR SET 1
15 100815 LED D-RGB strip 500/400 mm 1
16 3831109834282 Plug Cover (Black) 10
15
12
5
6
8
7
4
9
1
2
16
9
3
10
13
11
11
14

- 7 -
PREPARING THE O11D Mini CHASSIS
Before installing the distribution plate, carefully read
the PC case manual.
STEP 1
Unscrew the factory provided screws and remove the top panel
from the case.
STEP 2
STEP 2
Remove side and the front panel from the case.
STEP 1
FACTORY
PROVIDED SCREWS

- 8 -
INSTALLING THE DISTRIBUTION PLATE
STEP 1
Carefully place the EK-Quantum Reflection2PC-O11D Mini D5
PWM D-RGB distribution plate into the PC case and align the
mounting holes.
STEP 1
STEP 2
Secure the distribution plate to the chassis with eight (8) M4 x 8
DIN7991 screws (as shown in the diagram).
STEP 2
M4 x 8 7991DIN
SCREW For this step you will need:
Allen Key 2.5 mm
8
M4 x 8 7991DIN (8 pcs)

- 9 -
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS
It is mandatory to use at least one of each type of port and all
remaining ports should be sealed using the supplied plugs. The
EK-Loop Multi Allen Key may be used to install all EK fittings, do not
use excessive force.
If one of the prescribed components will not be installed (ie.
bottom radiator or GPU block) then one IN and one OUT port
must still be joined together in order for this distribution plate
to function!
7SLOT CONFIGURATION
ITX / mATX / ATX
PLUG
RADIATOR 2 IN
CPU OUT
CPU IN
RADIATOR 2 OUT
GPU IN/OUT (SLOT 1)
GPU IN/OUT (SLOT 2)
GPU IN/OUT (SLOT 3)
RADIATOR 1 OUT
DRAIN
RADIATOR 1 IN
GPU IN (SLOT 2)
GPU IN (SLOT 3)
RADIATOR 1
Up to S360 (bottom)
RADIATOR 2
Up to S240 (side)

- 10 -
FILL (EXTERIOR)
DRAIN (EXTERIOR)
RADIATOR 1
Up to S360 (bottom)
RADIATOR 2
Up to S240 (side)

- 11 -
5SLOT CONFIGURATION
ITX / mATX
RADIATOR 1
Up to S360 (bottom)
RADIATOR 3 (Optional)
Up to S360 (top)
RADIATOR 2 (Optional)
Up to S240 (side)
RADIATOR 2 IN
CPU OUT
RADIATOR 2 OUT
GPU IN/OUT (SLOT 1)
RADIATOR 1 OUT
RADIATOR 1 IN
DRAIN
CPU IN

- 12 -
FILL (EXTERIOR)
DRAIN (EXTERIOR)
RADIATOR 1
Up to S360 (bottom)
RADIATOR 3 (Optional)
Up to S360 (top)
RADIATOR 2 (Optional)
Up to S240 (side)

- 13 -
FLOW DIAGRAM

- 14 -
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector of the distribution plate D-RGB LED light
to the D-RGB HEADER on the motherboard. The LED will work if the
pin layout on the header is as follows: +5V, Digital, Empty, Ground.
D-RGB Header
RGB Header
CONNECTING THE PUMP
The EK-D5 PWM pump has two connectors.
1. SATA Connector: It must be connected directly to your PSU at all
times as it is used to power the pump.
2. 4-pin PWM fan: It can be connected to your motherboard’s
CPU_ Fan or designated water pump header. It can also be
connected to a controller. This cable is used to control and report
the rotational speed of the pump. If it’s not connected, the pump
will run at maximum speed (100% PWM).
SATA
CONNECTOR 4-PIN PWM FAN
CONNECTOR

- 15 -
To make sure the installation of EK components was successful, we
recommend you perform a leak test for 24 hours.
When your loop is complete and filled with coolant, connect the
pump to a PSU outside of your system. Do not connect power to
any of the other components. Turn on the PSU and let the pump
run continuously. It is normal for the coolant level to drop during this
process as air collects in the distribution plate.
Inspect all parts of the loop, and in the eventuality that coolant leaks,
fix the issue and repeat the testing process. Ensure that all hardware is
dry before the system is powered on in order to prevent any damage.
TESTING THE LOOP

In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND PRODUCT PARTS” where you can find the
EAN number of each part you might need.
Include the EAN number with quantity in your request.
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA