EK-Quantum Reflection2 V3000 Plus D5 PWM D-RGB Plexi User manual

USER GUIDE
DISTRIBUTION PLATE
EKQuantum
Reflection2V3000 Plus D5 PWM D-RGB - Plexi

The installation of the product is intended to be undertaken by
an adequately trained and experienced person. You are installing
the product at your own risk. If you are not sufficiently trained
or experienced or feel unsure about the installation procedure,
please refrain from installing the product yourself and contact
our tech support for assistance. We disclaim our liability for any
damages to the product and incidental, consequential, or indirect
damages incurred due to improper or inappropriate installation.
Before you start using this product please follow these basic guidelines:
Read this manual carefully before beginning the installation
process.
The EK-fittings require only a tiny amount of force to screw
them firmly in place since the rubber O-ring gaskets ensure the
liquid seal.
Corrosion-inhibiting purpose-made coolants are always
recommended for any liquid cooling system. EK recommends
EK-CryoFuel coolants for worry-free usage.

- 3 -
TABLE OF CONTENT
BOX CONTENTS 4
DISTRIBUTION PLATE DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6
PREPARING THE CHASSIS 7
INSTALLING THE DISTRIBUTION PLATE 8
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS 10
FLOW DIAGRAM 12
CONNECTING THE D-RGB LED STRIP 13
CONNECTING THE PUMP 13
TESTING THE LOOP 14
SUPPORT AND SERVICE 15
SOCIAL MEDIA 15

- 4 -
BOX CONTENTS
EK-Quantum Reflection2V3000 Plus D5 PWM D-RGB - Plexi
Screw M4 x 5 DIN7984 (8 pcs)M4 0.8 mm Washer (8 pcs)
Allen Key 2.5 mm (1 pc)
EK-Loop Multi Allen Key (1 pc)
Mounting mechanism - Reflection2
V3000 Plus D5 PWM; EAN 106804

- 5 -
DISTRIBUTION PLATE DIMENSIONS
62.6 mm
136.5 mm
157.5 mm
34.6 mm
49 mm
32.5 mm
60.5 mm
88.5 mm
249.4 mm
269.7 mm
290 mm
319.4 mm
339.7 mm
360 mm
388 mm
416 mm
459.5 mm
487.5 mm
506 mm
555 mm
75.3 mm
88.3 mm
29.5 mm
94.9 mm
108.5 mm
60.5 mm
506 mm

- 6 -
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
8
13
5
4
16
2
12
9
11
17
1
Technical Specification:
- Dimensions with the attached pump (W x D x H): 157.5 x 88.3 x 555 mm
- Reservoir volume: ~550 ml
- D-RGB LED count: 32
- D-RGB cable length: 800 mm
- D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)
Position EAN Description Quantity
1106801 TOP Plexi (Lid part) 1
2106800 TOP Plexi (Block part) 1
3105913 Pump holder 1
4106799 LED Cover (Black e.) 1
58311 Screw M4 x 20 DIN7984 4
65154 OR 52 x3 NBR50 1
73831109837597 EK D5 Pump 1
8104599 Mylar sticker 1
9100663 EK - Badge 1
10 100815 LED D-RGB strip 800/600 mm 1
11 102639 EK - Plug G1/4 12
12 3831109834282 EK-Quantum Torque Plug Cover - Black 12
13 106792 OR - V3000 Plus D5 PWM Set 1
14 8312 Screw M4 x 16 DIN7991 71
15 9051 Screw M4 x 25 DIN7991 6
16 9054 Screw M4 x 16 DIN7984 8
17 106803 Metal mounting Plate (Black) 1
10
3
7
6
15
14

- 7 -
PREPARING THE CHASSIS
Before installing the distribution plate, carefully read the
PC case manual.
STEP 1
First, remove the PC case’s front panel. After that, you can remove
the top and side panels.
STEP 2
STEP 2
After removing the panels, the inner two (2) SSD plates (besides
the motherboard) and the PSU Shroud also need to be detached.
STEP 1
TOP PANEL
SIDE
PANELS
SIDE PANEL S
FRONT PANEL

- 8 -
STEP 3
To functionally use the distribution plate to it’s full potential you also
have to remove the two (2) drive cages.
Note: If you will not use the side radiator configuration, one
of the drive cages can still be inserted back into the case.
STEP 3
INSTALLING THE DISTRIBUTION PLATE
STEP 1
It is recommended that a distribution plate is installed into
the chassis before radiators with fans.
Carefully insert the distribution plate into the PC Chassis.
STEP 1
DISTRIBUTION
PL ATE

- 9 -
STEP 2
Secure the distribution plate from the backside using eight (8) M4X5
DIN7984 Screws and eight (8) M4 0.8 mm Washers with provided
Allen Key 2.5 mm.
STEP 2
For this step you will need:
Allen Key 2.5 mm (1 pc) M4x5 DIN7984 Screw (8 pcs)
M4 0.8 mm Washer (8 pcs)
M4 x 5 DIN7984
SCREW
M4 0.8 mm
WASHER

- 10 -
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS
GPU OUTLET
FRONT / SIDE
RADIATOR OUTLET
To complete your loop, all ports must be used as marked in the
image.
All remaining unused ports must be closed with supplied plugs,
using the EK-Loop Multi Allen Key.
If one of the prescribed components will not be installed
(ie. side radiator or GPU block) then one INLET and one
OUTLET port must still be joined together in order for
this distribution plate to function!
Only one INLET and one OUTLET port for the GPU
connection can be used, while all other INLET and
OUTLET GPU ports must be closed with G1/4 plugs.
CPU OUTLET
TOP RADIATOR
INLET
SIDE RADIATOR
INLET
CPU INLET
TOP RADIATOR
OUTLET
FRONT RADIATOR
INLET
FILL
DRAIN
GPU INLET

- 11 -
DRAIN
FILL

- 12 -
FLOW DIAGRAM

- 13 -
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector of the distribution plate D-RGB LED light
to the D-RGB HEADER on the motherboard. The LED will work if the
pin layout on the header is as follows: +5V, Digital, Empty, Ground.
D-RGB Header
RGB Header
CONNECTING THE PUMP
The EK-D5 PWM pump has two connectors.
1. SATA Connector: It must be connected directly to your PSU at all
times as it is used to power the pump.
2. 4-pin PWM fan: It can be connected to your motherboard’s
CPU_ Fan or designated water pump header. It can also be
connected to a controller. This cable is used to control and report
the rotational speed of the pump. If it’s not connected, the pump
will run at maximum speed (100% PWM).
SATA
CONNECTOR
4-PIN PWM FAN
CONNECTOR

- 14 -
To make sure the installation of EK components was successful, we
recommend you perform a leak test for 24 hours.
When your loop is complete and filled with coolant, connect the
pump to a PSU outside of your system. Do not connect power to
any of the other components. Turn on the PSU and let the pump
run continuously. It is normal for the coolant level to drop during this
process as air collects in the distribution plate.
Inspect all parts of the loop, and in the eventuality that coolant leaks,
fix the issue and repeat the testing process. Ensure that all hardware is
dry before the system is powered on in order to prevent any damage.
TESTING THE LOOP

In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND PRODUCT PARTS” where you can find the
EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”
Thermal pads are readily available in the EK shop
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA