EK-Quantum Vector RTX 3080/3090 Backplate User manual

USER GUIDE
BACKPL AT E
EK-Quantum
Vector RTX 3080/3090 Backplate

This product is intended for installation by expert users only. Please
consult with a qualified technician. Improper installation may result
in damage to your equipment. EK assumes no liability whatsoever,
expressed or implied, for the use of this product or its installation. The
following instructions are subject to change without notice. Please, read
the manual carefully before beginning with the installation process. For
updates, you can visit our official website www.ekwb.com.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process, to prevent any possible damage to your
GPU or its circuit board (PCB).

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
BACKPLATE DIMENSIONS 5
INSTALLING THE BACKPLATE 6
PREPARING THE GRAPHICS CARD 6
CUTTING AND PLACING THERMAL PADS 6
ATTACHING THE BACKPLATE 8
TESTING THE LOOP 8
WARRANTY 9
REQUIRED TOOLS 9
SUPPORT AND SERVICE 10
SOCIAL MEDIA 10

- 4 -
BOX CONTENTS
4 mm
6 mm
7mm
M2.5 Nut (5 pcs)
M2,5x6 AX1 Screw (7 pcs)
Thermal PAD G 1,5mm - (120x24mm) (2 pcs) Thermal PAD G 2 mm - (120x24mm) (2 pcs)
M2,5x7 AX1 Screw (7 pcs)
M2,5x4 AX1 Screw (3 pcs)
EK-Quantum Vector RTX 3080/3090 Backplate
PVC Washer M2.5 (10 pcs)
120 mm
24 mm
120 mm
24 mm
120 mm
24 mm
Thermal PAD G 1,0mm - (120x24mm) (2 pcs)
Mounting mechanism - You may not need all the screws, mounting mechanism is universal!

- 5 -
BACKPLATE DIMENSIONS
220,15 mm
99 mm
5,20 mm

- 6 -
INSTALLING THE BACKPLATE
STEP 1
PREPARING THE GRAPHICS CARD
First, complete the installation of your EK-Quantum Vector RTX
3080/3090 water block according to its installation manual.
In case the water block is already installed, remove the six (6) AX1
screws and their PVC washers, as shown in the image.
STEP 2
CUTTING AND PLACING THERMAL PADS
Your backplate comes with thermal pads that have to be cut into
smaller pieces to cover all the VRM components. EK made sure to
provide you with more than an adequate quantity of thermal pads to
complete this Step.
CAUTION: You must remove the protective foil from both
sides of the thermal pad before installation.
Thermal pads:
2x Thermal PAD G 1.0 mm (120 x 24 mm) – EAN: 3830046996770
2x Thermal PAD G 1.5 mm (120 x 24 mm) – EAN: 3830046996787
2x Thermal PAD G 2.0 mm (120 x 24 mm) – EAN: 3830046996794
STEP 1
STEP 2
120 mm
24 mm
1 mm
Thermal PAD G 1.0 mm (120 x 24 mm)
120 mm
24 mm
1.5 mm
Thermal PAD G 1.5mm (120 x 24 mm)
120 mm
24 mm
2 mm
Thermal PAD G 2.0 mm (120 x 24 mm)

- 7 -
STEP 3
Once cut to size, thermal pads should be placed on the backplate,
as illustrated below.
STEP 3
RTX™ 3080
RTX™ 3090
Thermal Pad G 1.5 mm
Thermal Pad
G 2.0mm
Thermal Pad G 1.5 mm
Thermal Pad
G 1.0 mm
Thermal Pad
G 2.0 mm

- 8 -
STEP 4
ATTACHING THE BACKPLATE
Place the backplate on the PCB and make sure all holes are aligned.
Position an M2.5X7 AX1 screw in each of the six (6) mounting holes
(as shown in the image) and tighten them evenly with a Phillips
head screwdriver. Do not use excessive force!
For this Step, you will need:
STEP 4
TESTING THE LOOP
To ensure the installation of EK components was successful, we
recommend you perform a 24-hour leak test.
When your loop is complete and filled with coolant, connect the pump
to a PSU outside your system. Do not connect power to any of the other
components. Turn on the PSU and let the pump run continuously.
Inspect all parts of the loop, and in case the coolant leaks, fix the issue
and repeat the testing process. To prevent possible damage, please
ensure that all hardware is dry before the system is powered on.
Phillips Head
Screwdriver
M2.5 x 7 AX1
6 pcs
7mm
M2.5X7 AX1

- 9 -
Phillips Head Screwdriver Scissors
REQUIRED TOOLS
WARRANTY
Our products are warranted against defects of materials and quality for
a period of 24 months, starting with the date of delivery to the end-user.
During this period, products will be repaired or have parts replaced at
our discretion, provided that 1) the product is returned to the agent from
whom it was purchased; 2) the product has been purchased by the end-
user and has not been used for commercial purposes; 3) the product has
not been misused, handled carelessly, or used in a manner other than the
way described in the instructions manual. This warranty does not confer
rights other than those expressly set out above and does not cover any
claims for consequential loss or damage. This warranty is offered as an
extra benefit and does not affect your statutory rights as a consumer.
This warranty is voided if the product comes in contact with aggressive
UV additives or other improper liquids. EK water blocks are sealed with a
warranty-voiding circular label, proving the water block has withstood a
pressure leak test. Removing the label will void the leak-free guarantee,
but not the guarantee on the product itself. Any other RMA issues can
be reported to EK Customer Support at www.ekwb.com/support for
further analysis.

In case you need assistance, please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA