JETWAY FFI02 Series User manual

1
Quick Installation Guide
NO. G03-FFI02QIG-F
Rev: 1.0
Release date: 2021-12-13
Notice:
The photos in this file are for illustration purpose only. The model may not be the latest version. Please
refer to the product you purchased for actual specification.

2
I. To Open the Chassis
1. Locate the screws in the spots marked on
the top cover of the system and unscrew
them one by one.
2. Turn over the bare bone system with the
heatsink upwards, as the photo shows.
3. Remove the screws in the marked spots on
the front panel.
4. Remove the screws in the marked spots on
the rear panel.

3
5. Remove the IO panels and lift the cover up
to open the chassis. For user to have a
clear view of layout, we may unplug some of
the cables during installation.
6. For CPU installation, user needs to remove
the screws on the marked spots to
dissemble the motherboard form chassis
cover.
Notice: 1. If the system is pre-installed with CPU heatsink, user needs to remove the screws on the
backside of the board to dissemble the heatsink before CPU installation; 2.Make sure that the cables are
plugged into their original places when necessary installation finished for the system to function normally.

4
II. To Install CPU
1. Find CPU socket on the board. Please make
sure that CPU socket is facing towards you
and the level is on you right hand side.
2. Remove the plastic protective cover from the
socket (Put it to the original place if CPU is
not installed. Do not touch the metal contact
pins of the CPU socket).
3. Press down the level and move it towards the
right side to free it from the hook.
4. Open the level upwards about 135 degree
and the metal protection plate will be pulled
up at the same time.

5
5. Make sure that Pin-1 Golden Finger Indicator in the place as shown in the above
photo and match the two alignment keys on the CPU with two points of the socket.
CPU can only be correctly installed in this direction. Incorrect installation might
cause damage to CPU.
6. Put down the load plate in the direction shown
above.
7. Press down the load level and move it
leftwards to make sure it is locked under the
notch.
Golden Finger
Indicator
Alignment Key
Alignment Key

6
III.To Install Heatsink Thermal pads
1. Find the above CPU heatsink and CPU thermal pad package. Remove the protective films
on the both sides of the pad and apply it upon the bottom side of the heatsink for better heat
conduction.
2. Place the CPU heatsink upon the
installed CPU. The screw holes of the
heatsink should match corresponding
screw holes of the board. And then apply
corresponding thermal pad to the top
side of the heatsink as the photo shows.
3. Apply corresponding thermal pads to chipset
heat sink (HCS3XXHS2-F*2pcs). When
installation finished, tear off the protective film
from the pads before assembling the back cover
to the chassis.
Bottom Side
Paste Here!
Top Side
Paste Here!
Tear off the
Protective films
P/N:
HCS310HS1-F* 2pcs
60*52*1.0mm

7
4. Turn the board over and lock the heatsink to the board by tightening the screws (P/N: LCSC378M01-F*4)
on the marked spots.
5. Thermal pads need to be attached to the bottom of the motherboard, which will help the system to
dissipate heat (P/N: HCSHBFFHS1-1F*9).

8
*Note: There should be one more HCS310HS1-F / HCS3XXHS2-F / HCSHBFFHS1-1F left as spare parts
after normal assembly. User can use them to replace corresponding damaged thermal conductive pads.
Notice：Please restore the screws that lock the motherboard to the chassis cover when CPU & heatsink
installation completed. The cables unplugged during this process should be plugged to their original places
after heatsink installation.
IV. To Install SO-DIMM to the board
1. Find the SO-DIMM slot on the board.

9
2. Insert the gold-figure side of the compatible SO-DIMM into the slot at a 30 degree angle. See to it that the
break of the module fit into the notch of the slot.
3. Press down to secure the SO-DIMM to the slot. The eject tabs will lock automatically if installing direction
is correct.

10
V. To Install M.2 E-Key (2230) PCIe card
1. Locate the M.2. PCIe, type-2230 slot on
the board.
2. Remove the marked screw nut reserved
for M.2 PCIe card installation first.
3. Insert the gold-figure side of compatible card
into M.2. PCIe slot. See to it that the
golden-figure side is fully inserted into the slot.
4. Lock the card to the board by tightening up
the screw nut to the marked spot.

11
5. Locate the reserved Wi-Fi antenna holes on the back panel. Remove the dust-proof plugs
on the marked spots from the panel to install the antenna, as the following details show.
a) Back-side View: Put the metal ring into the antenna head at first, and then push this
antenna head into antenna hole of the rear panel.
b) Front-side View: Put the other washer① into the antenna head, and then lock the
antenna head to the front side of the back panel with the with hexagonal bolt②and
tighten it up.

12
6. The metal hats on the end of the antenna
string are sealed by acetate tape to avoid
possible damage to the system.
7. Tear off the tape to find metal hats of
Wi-Fi antenna string.
8. Press the metal hat on the end of the
antenna string to the antenna slot on the card
as shown.
9. Connect the external Wi-Fi receiver
antenna to the antenna connector on the
rear panel.

13
VI. To Install M.2 B-Key (3042/3052) card
1. Locate the M.2 B-Key, type-3042/3052 slot on
the board.
2. Remove the marked screw with a screwdriver.
3. Insert the gold-figure side of compatible M.2
3042 card into the slot until the golden finger side
fully emerged into the slot.
4. Install the screw back to the original spot.
*Note: the screw post and nut fixed at location MH1 by default for 4.2cm type-3042 card installation. If you
wish to install type-3052 card, please remove the screw of the location MH3 before installing 5.2cm card to
the slot. The other steps are the same as 3042 card installation. (Used main board: MI02-R03)

14
VII. To Install M.2 M-Key (2280) card
1. Locate the M.2 M-Key, type-2280 slot on the
board.
2. Remove the marked screw with a screwdriver.
3. Insert the gold-figure side of compatible M.2
2280 card into the slot until the golden finger
side fully emerged into the slot.
4. Install the screw back to the original spot.

15
VIII. To Install Hard Disk
1. Remove the screws in the marked spots on the front panel.
2. Lock the SATA hard disk to one of the racks by tightening the screws in the marked spots.

16
3. Lock the SATA hard disk to the other rack by tightening the screws in the marked spots.
4. Insert the gold-figure side of the compatible STAT HDD into the slot.

17
5. Install the screw back to the original spot.
6. Find the compatible SATA cable for the system in the accessories package.

18
7. Plug this side of the cable to SATA power-in 8. Lock the racks with SATA HDD installed
connector and SATA connector of the hard disk. to its original places by tightening the
screws in the marked spots.
9. Plug the other sides of the cables into the SATA power connector and SATA port connector on the board.

19
Notice:
When all necessary installations are finished, please make sure that all cables unplugged before
installations are connected to their original places before restoring the back cover to the chassis and
screws on the front panel/back panel/top cover locked to its original places (Refer to Part I). See to it that
the cables inside are not blocked or pressed.
IX. To Wall Mount the System
1. Install wall mount rack to the system by tightening the screws in the marked positions. Then lock the
other three screws on the other side in the same way.

20
2. Wall mount the system by tightening two screws in the marked positions. Then tighten up the other
two screws in the marked positions on the other rack.