EK-Quantum Reflection2 7000D D5 PWM D-RGB User manual

USER GUIDE
DISTRIBUTION PLATE
EKQuantum
Reflection27000D D5 PWM D-RGB

Please note the installation of the product is intended to be
undertaken by an adequately trained and experienced person.
You are installing the product at your own risk. If you are not
properly trained or experienced or feel unsure about the
installation procedure, please refrain from installing the product
yourself and contact our tech support for assistance. We disclaim
our liability for any damages to the product as well as incidental,
consequential, or indirect damages incurred due to improper or
inappropriate installation.
Before you start using this product please follow these basic guidelines:
Please carefully read the manual before beginning with the
installation process!
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting coolants
is always strongly recommended for any liquid cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.

- 3 -
TABLE OF CONTENT
BOX CONTENTS 4
DISTRIBUTION PLATE DIMENSIONS 5
MAIN PARTS AND TECHNICAL SPECIFICATIONS 6
PREPARING THE CASE 7
PREPARING AND INSTALLING THE DISTRIBUTION PLATE 8
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS 9
FLOW DIAGRAM 11
CONNECTING THE D-RGB LED STRIP 12
CONNECTING THE PUMP 12
TESTING THE LOOP 13
SUPPORT AND SERVICE 14
SOCIAL MEDIA 14

- 4 -
BOX CONTENTS
5 mm
EK-Quantum Reflection27000D D5 PWM
D-RGB
Screw M4 x 5 DIN7984 Screw (4 pcs)
Allen Key 2 mm (1 pc)
Allen Key 2.5 mm (1 pc)
EK-Loop Multi Allen Key (1 pc)

- 5 -
DISTRIBUTION PLATE DIMENSIONS
135 mm
463.5 mm
42.5 mm
107.5 mm
135.5 mm
183.2 mm
203.2 mm
253.2 mm
273.5 mm
293.9 mm
321.9 mm
349.9 mm
414.5 mm
443.5 mm
25 mm
51 mm
114 mm
76 mm
30 mm
20 mm
51 mm
421 mm

- 6 -
MAIN PARTS AND TECHNICAL SPECIFICATIONS
13
9
7
8
10
5
11
6
12
1
14
Technical Specification:
- Dimensions with the attached pump (W x D x H): 215.1 x 77.8 x 471.9 mm
- D-RGB LED count: 24
- D-RGB cable length: 500 mm
- D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)
Position EAN Description Quantity
1105707 Bottom plate (Plexi) 1
2105708 Top plate (plexi) 1
3101803 Pump bracket 1
43831109837597 EK-D5 PWM (12V SATA) 1
5104599 Mylar sticker 1
6105709 LED Cover 1
7100815 LED strip 500/400mm 1
88312 Screw M4x16 DIN7991 47
99061 Screw M3x25 DIN7991 4
10 8311 Screw M4x20 DIN7984 4
11 100663 EK - Badge 1
12 105712 OR Set 1
13 5154 Pump OR 52x3 mm 1
14 3831109834282 Plug Cover (Black) 10
15 102639 EK -Plug G1/4 (Nickel) 10
3
4
2
15

- 7 -
PREPARING THE CASE
Before installing the distribution plate, carefully read
the PC case manual.
STEP 1
First, open the side panel and the inner frame of the PC Case.
(shown in the photo).
STEP 2
STEP 2
Using Phillips head screwdriver, unscrew the factory-provided
UNC screws and remove the Radiator bracket from the PC case.
Save the screws and radiator bracket for later use.
STEP 1
REMOVE
For this step you will need:
Phillips Head Screwdriver
SIDE
PANEL
INNER FRAME

- 8 -
STEP 2
Secure the Radiator bracket with the pre-installed distribution plate
into the PC Case using five (5) saved factory-provided UNC screws.
STEP 2
PREPARING AND INSTALLING THE DISTRIBUTION PLATE
STEP 1
Carefully place the EK-Quantum Reflection27000D D5 PWM D-RGB
onto the saved Radiator bracket.
Secure the distribution plate using Allen Key 2.5 mm and M4 x 5
DIN7984 Screws. Do not use excessive force.
STEP 1
For this step you will need:
Allen Key 2.5 mm (1 pc)
M4 x 5 DIN7984 SCREW R A DI ATO R
BRACKET
For this step you will need:
Phillips Head Screwdriver

- 9 -
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS
CPU OUTLET
BOTTOM
RADIATOR
OUTLET
BOTTOM
RADIATOR
INLET
CPU INLET
TOP RADIATOR
OUTLET
DRAIN
TOP RADIATOR
INLET
GPU OUTLET
GPU INLET
To complete your loop, all ports must be used as marked in the
image.
All remaining unused ports must be closed with supplied plugs,
using the EK-Loop Multi Allen Key.
If one of the prescribed components will not be installed
(ie. bottom radiator or GPU block) then one INLET and
one OUTLET port must still be joined together in order
for this distribution plate to function!
Only one INLET and one OUTLET port for the GPU
connection can be used, while all other INLET and
OUTLET GPU ports must be closed with G1/4 plugs.

- 10 -
FILL
DRAIN

- 11 -
FLOW DIAGRAM

- 12 -
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector of the distribution plate D-RGB LED light
to the D-RGB HEADER on the motherboard. The LED will work if the
pin layout on the header is as follows: +5V, Digital, Empty, Ground.
D-RGB Header
RGB Header
CONNECTING THE PUMP
The EK-D5 PWM pump has two connectors.
1. SATA Connector: It must be connected directly to your PSU at all
times as it is used to power the pump.
2. 4-pin PWM fan: It can be connected to your motherboard’s
CPU_ Fan or designated water pump header. It can also be
connected to a controller. This cable is used to control and report
the rotational speed of the pump. If it’s not connected, the pump
will run at maximum speed (100% PWM).
SATA
CONNECTOR
4-PIN PWM FAN
CONNECTOR

- 13 -
To make sure the installation of EK components was successful, we
recommend you perform a leak test for 24 hours.
When your loop is complete and filled with coolant, connect the
pump to a PSU outside of your system. Do not connect power to
any of the other components. Turn on the PSU and let the pump
run continuously. It is normal for the coolant level to drop during this
process as air collects in the distribution plate.
Inspect all parts of the loop, and in the eventuality that coolant leaks,
fix the issue and repeat the testing process. Ensure that all hardware is
dry before the system is powered on in order to prevent any damage.
TESTING THE LOOP

In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND PRODUCT PARTS” where you can find the
EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”
Thermal pads are readily available in the EK shop
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA