EK-Quantum Velocity D-RGB - AMD Ryzen Edition User manual

USER GUIDE
1st Revision – November 25, 2020
CPU WATER BLOCK
EKQuantum
Velocity D-RGB - AMD Ryzen Edition

These products are intended for installation by expert users only. Please
consult with a qualified technician for installation. Improper installation
may result in damage to your equipment. EK Water Blocks assumes no
liability whatsoever, expressed or implied, for the use of these products,
nor their installation. The following instructions are subject to change
without notice. Please visit our web site at www.ekwb.com for updates.
Before installation of this product please read all important notices,
disclosures and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
Read the entire manual before you start installation!
Please remove your motherboard from the computer to ensure the
safest possible mounting process and to prevent the possibility of
damage to your GPU or any printed circuit boards (PCB’s).
EK-Quantum Torque fittings require only a small amount of force
to screw them firmly in place since the liquid seal is ensured by
compression of the rubber O-ring gaskets and not the thread itself.
Only G1/4 fittings with a parallel thread should be used (1/4” BSPP),
maximum thread engagement is strictly 5.75mm!
The use of corrosion inhibiting coolants are always recommended
for any liquid cooling system.
Do not use pure distilled water! For best results EK recommends the
use of EK-CryoFuel coolants!
Make sure to thoroughly bleed air out of your CPU Water Block or
you will not achieve optimal performance!

QUICK INSTALLATION GUIDE
- 3 -
INSTALLING THE WATER BLOCK 8
AMX AND FMX SOCKET MOTHERBOARDS 8
CONNECTING THE D-RGB LED STRIP 11
REPLACING THE D-RGB LEDs 11
TABLE OF CONTENTS
BOX CONTENTS 4
REQUIRED TOOLS 5
GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY 5
WATER BLOCK DIMENSIONS 6
WATER BLOCK SPECIFICATIONS AND MAIN PARTS 7
SUPPORT AND SERVICE 12
SOCIAL MEDIA 12

- 4 -
BOX CONTENTS
Thumb Nut (4)
Thermal Grease (1)
Allen Key 2.5mm (1)
Standoff (4)
EK-Quantum Velocity D-RGB - AMD Ryzen
Edition - CPU Water Block (1) Rubber Gasket (1)Metal Backplate (1)
M4 x 0.8 PA Washer (4)
Spring (4)

- 5 -
GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY
This CPU liquid cooling unit is pre-assembled for use with modern AMD
desktop socket type motherboards. By default (out of the box) this water
block supports the following CPU sockets:
- AMD® socket AMx and FMx
Phillips Head Screwdriver
REQUIRED TOOLS

- 6 -
WATER BLOCK DIMENSIONS
87
102
54
90
24

- 7 -
WATER BLOCK SPECIFICATIONS AND MAIN PARTS
Technical Specifications:
- Dimensions (LxHxW): 102 x 87 x 24 mm
- D-RGB (Adressable RGB) Cable Length: 300 mm
- D-RGB LED Count: 20
- D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)
EK-BADGE
J E T P L ATE
SEALING GASKET
LED COVER
D-RGB LEDs PCB
MOUNTING BRACKET
COLDPLATE
SCREW M4x14 DIN7991
TOP P L ATE

- 8 -
AMx AND FMxSOCKET MOTHERBOARDS
STEP 1
Use a Philips head screwdriver to remove four (4) UNC 6-32 screws
securing the plastic hold-down clamps to the motherboard.
Remove the clamps and the original motherboard backplate, and
store them away. See the illustration to identify those parts.
AMD® FACTORY
BACK PL AT E
UNC 6-32
SCREWS
HOLD-DOWN
CLAMPS
STEP 1
INSTALLING THE WATER BLOCK
STEP 2
Turn your motherboard face down and position the Rubber Gasket
and Backplate directly in line with the mounting holes. The ribbed
side of the backplate should be turned face up! Once aligned,
carefully rotate the motherboard assembly while holding the
backplate in position with the other hand.
AM4
M E TAL BAC K PL AT E
RUBBER GASKET
MOTHERBOARD
STEP 2

- 9 -
STEP 3
Loosely install all four standoffs and plastic washers before
proceeding to tighten them completely. It is mandatory to install
plastic washers as they prevent damage to the motherboard PCB.
Using pliers or similar tools is not recommended.
STANDOF F
PA WASHER
STEP 3
STEP 4
Wipe the IHS clean using a non-abrasive cloth or Q-tip, as shown in
the image. Once it’s clean, apply a line of Thermal Compound to one
edge of the IHS and use a plastic card or something similar to spread
it evenly. The layer of Thermal Compound must be thin and even in
thickness over the entire surface of the IHS. The excessive or uneven
application will lead to poor performance!
Non-abrasive
cloth
IHS
STEP 4

- 10 -
STEP 5
Remove the protective sticker and position the CPU water block onto the
standoffs. Place the springs and thumb nuts over each standoff before
tightening them two revolutions at once, in a cross pattern. Do not tighten
them fully until all of them are partially screwed in.
STEP 5
THUMB NUT
COILED SPRING
STEP 6
Tighten the fitting barbs in a clockwise direction until the O-ring
underneath is compressed.
STEP 6
FITTING RING
FITTING BARB
INLET
PORT
OUTLET PORT

- 11 -
CONNECTING THE D-RGB LED STRIP
STEP 1
D-RGB HEADER
D-RGB LEDs PCB
J E T P L ATE
SEALING GASKET
RGB HEADER
STEP 1
Plug the 3-pin D-RGB connector from your CPU water block to the
D-RGB header on your motherboard or controller. The LED strip will
work only if the pin layout on the header is as follows: +5V, Data,
Empty, Ground.
Incorrect installation or installation to the incorrect header
may result in damage to the LED strip or the header itself!
REPLACING THE D-RGB LEDs
SCREW M4x14 DIN 7991
Use the Allen key to unscrew four (4) M4 x 14 screws from the bottom
of the water block.
Carefully disassemble the block and replace the LED’s PCB unit.
Make sure the Jet plate and the O-ring are well aligned when you put
everything back together.

In case you need assistance, please contact:
https://www.ekwb.com/customer-support/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA