EKEN V6 User manual

User Manual 2.0
Video Doorbell
V6

Features
8. Restart Button
9. Micro USB Port (Battery Charging)
1. Microphone
2. Wide-angle Lens
3. Light Sensor
4. Hidden Infrared Lights
5. Push Button
6. LED Indicator
7. Speaker

In the box
Video
Doorbell
5 Mounting
Screws 2 Security Screws
Mounting
Bracket
Video
Doorbell
User Manual
5 Anchors
Tape
Chime
(Optional)
2 Batteries
(Optional)
Indicator Light
Indicator light flashing RED
Indicator light flashing RED
and BLUE alternately
The device is reconnecting to the
Wifi network. Please wait.
Low battery. Please recharge your
batteries.

Charge batteries
WARNING: Lots of events
If your device is capturing an excessive number of
events every day, you might need to recharge your
battery sooner. Plus, the battery is also drained each
time you use the Live View to look or speak through
your doorbell. To prevent excessive events, you can
adjust your motion settings to a lower sensitivity.
1. Remove the battery tab.
3. Fully charge batteries by connecting your device to a
USB charger using a Micro USB cable. It takes about
14 hours for batteries to fully charge.
2. Insert 18650 batteries
positive end facing down,
as shown on the device.
Rechargeable 18650 Battery

Set up your Video Doorbell
Scan the QR codes below or search for Aiwit on the
Apple app store or Google Play to download the app.
The app will walk you through setting up your doorbell.
Step 1
Open the Aiwit app on
your cellphone. Tap Log
in/Sign up. Then tap sign
up.
Step 2
Enter your email and
password, then tap Sign
up.
Step 3
Aiwit Android / iOS
App Download

You will receive an email
with the confirmation
code. Please enter the
code and tap Confirm.
Step 4
Enter your email and
password, then tap Log in.
Step 5
Tap + .
Step 6
Tap Doorbell Scan and
select Video doorbell.
Step 7

Press and hold the doorbell
button for 8 seconds until
the doorbell light is flashing
red. Tap Next.
Step 8
Tap Yes.
Step 9
Find or enter the name of
your Wifi network and
enter the Wifi password.
Tap Next.
Step 10
Scan the QR code using
the doorbell camera. Keep
devices 4 inches (10 cm)
apart.
Step 11
4 inches (10 cm)

If pairing is successful, you
will see a message as
below.
Step 12
After setup, tap the Live
View in the Aiwit app to
see live video from your
doorbell.
Step 13

Install your Video Doorbell
Mark drill holes and use a bit to drill holes in your wall.
Insert anchors and secure your doorbell with mounting
and security screws.
Step 1
Step 2 Step 3 Step 4
Slide
Down
Tighten
The Screw
WallWallWall

Frequently asked questions
How to RESET the doorbell
Press and hold the Doorbell Button for 8 seconds. Then
follow the in-app instructions to finish your Wi-Fi setup.
How to share the device with my family
Open the Aiwit app. From the home page, tap the Share
icon. Tap Share via Email or Share via QR Code. You
can share the device with up to 8 users.
Share via Email:
The new user has to download the Aiwit app and
create an account with the same email address which
the device owner has shared with. Log in to the
account and you'll see the shared device.
Share via QR Code:
1. Open the Aiwit App on a new user's smartphone.
2. From the home page, tap +.
3. Tap QR Code Sharing, then scan the QR code the
device owner generated before.
4. You will see Share successful, then tap Confirm.
How many users can view the video at the same
time?
Up to 3 users may view the video feed, but only 1 user
can use the direct intercom. Both iOS and Android are
compatible
Why is my Wi-Fi signal poor on my device?
Your device may be too far away from your wireless
router or you may have some obstructions in between
that reduce signal strength. You might try repositioning
your router or getting a signal extender/repeater for
your wireless router.

Is 5GHz Wi-Fi supported?
No. Only 2.4GHz Wi-Fi is supported.
How to enable Notifications on my phone
To do this, you need to give permission for the Aiwit app
to access to your microphone and enable notifications.
Follow these steps to enable notifications.
1. Open Settings. Go to Aiwit app permissions and
select Notifications.
2. Make sure all switches are on.

Set up your Wireless Chime (Optional)
NOTICE:
Connect the video doorbell to the doorbell chime, and
get instant alert in your home when someone rings the
doorbell. The chime plugs into any wall outlet, you can
place it anywhere in the home.
The video doorbell is only compatible with our wireless
chime, and not compatible with traditional doorbell chimes.
The wireless chime is optional. If it is not installed, doorbell
notifications will still go directly to the Aiwit app.
The Basics
Tune
Connect
Volume
up
Volume
down

Step 1
Set up your chime with the video doorbell.
Before the setup process, be sure your video doorbell has
connected to your phone and plug in your chime.

Step 2 Step 3
Press the Doorbell Button
to pair your doorbell to the
chime.
Step 4
Press the Doorbell Button
again to make sure it’s the
tune you selected.
Step 5
Press the Tune Button to
cycle through 38 different
tunes and select a tune.
Press the Connect Button.