ekwb EK-FC GV100 PRO User manual

INSTALLATION MANUAL
EK-FC GV100 PRO
GPU WATER BLOCK

- 2 -
This product is compatible with Nvidia Quadro GV100 graphic card.
It is intended for installation only by expert users. Please consult with
a qualified technician for installation. Improper installation may result
in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor
their installation. The following instructions are subject to change
without notice. Please visit our web site at www.ekwb.com for updates.
Before installation of this product please read important notice,
disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic
guidelines:
Please carefully read the manual throughly before beginning
with the installation process!
Please remove your graphics card from computer to assure
safest mounting process in order to prevent any possible
damages to your GPU and/or graphics card circuit board(PCB).
The EK fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
Do not use pure distilled water! For best results EK recommends
the use of EK-CyroFuel coolants!

- 3 -
TABLE OF CONTENT
PREPARING YOUR GRAPHICS CARD 4
INSTALLING THE WATER BLOCK 6
CHECKING FOR CONTACTS 8
INSTALLATION OF FITTINGS AND TUBING 8
INSERTING THE CARD IN YOUR PC CASE 9
REQUIRED TOOLS 9
SUPPORT AND SERVICE 10
SOCIAL MEDIA 10

- 4 -
PREPARING YOUR GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Remove all encircled screws using Phillips screwdriver. All heat
sink assembly screws should be removed, including self-adhesive
washers on both sides of the PCB (if present). Also remove encircled
screws on the IO bracket.
STEP 1
Remove all screws on
the IO bracket using
Phillips screwdriver
STEP 2
CLEANING THE PCB
Carefully detach the original stock cooler after removing all screws
securing in to the board. Wipe off the remains (by using non-
abrasive cloth or q-tip, as shown on sample photo) of the original
thermal compound until the components and circuit board are
completely clean. EKWB recommends the use of denatured alcohol
for removing TIM leftovers.
STEP 2

- 5 -
STEP 3
APPLYING THERMAL COMPOUND
Wipe off the remains(by using non-abrasive cloth or q-tip) of the
original thermal compound until the components and circuit board
are completely clean.
Apply thermal compound: lightly coat GPU chip with enclosed EK-
TIM Ectotherm thermal grease. EKWB recommends to apply thermal
grease in cross form for best performance (see sample photo).
STEP 4
CUTTING THERMAL PADS
Your block comes with thermal pad (F=1.0mm) which needs to be cut
to smaller chunck in order to cover all the VRM components such as
MOSFETs, IC memory and coils.
PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE
THERMAL PADS PRIOR TO INSTALLATION.
Replacement thermal pads:
1. Thermal PAD F 1.0mm - (120x16mm) - (EAN: 3830046996732)
STEP 5
PLACING THERMAL PADS ON PCB
Place thermal pads on the circuit board as shown in the picture below.
Refer to numbering in previous picture when applying thermal pads of
different sizes or thickeness. EK made sure to provide customers with
more than adequate quantity of thermal pads to complete this step.
STEP 3
Thermal pad F – 1.0 mm
16
120
STEP 4
STEP 5

- 6 -
INSTALLING THE WATER BLOCK
STEP 1
PLACING THE BLOCK ON TO THE GRAPHICS CARD
Carefully position the water block with preinstalled standoffs on to
the graphics card. During this process please make sure you align
mounting holes on the PCB with holes on the water block (same
applies for other tops). Also pay attention not to use too much
force by pressing the block down to the PCB. Chip dies are prone
to cracking.
STEP 1
M2.5 x 6 AX1
13 pcs
M 2.5 PVC washer
16 pcs
M2.5 x 4 AX1
16 pcs
M2.5 x 8 AX1
2 pcs
M3 x 4 DIN7985
2 pcs
Phillips-head
screwdriver
M 2.5 PVC washer
13 pcs
M 2.5 PVC washer
13 pcs
BAG CONTENT
Bag content is universal for all water blocks, you may not need all screws
M2.5 Helix nuts
6 pcs
M2.5 Helix nuts
2 pcs

- 7 -
STEP 2
ATTACHING THE BLOCK TO THE GRAPHIC CARD
Use a Phillips screwdriver screw with the enclosed M2.5x4 AX1
screws. EKWB recommends users to start tightening the screws
around the GPU core and continue outwards. Always use a plastic
washer under each and every screw! If the washer is already present
on the circuit board there is no need for additional washer.
STEP 2
M2.5 Helix nuts
M2.5x4 AX1 Screw
Plastic washer
M 2.5 PVC washer
13 pcs
M2.5 Helix nuts
2 pcs
M2.5 x 6 AX1
2 pcs
M2.5 x 4 AX1
11 pcs
M2.5x6 AX1
Screws

- 8 -
INSTALLATION OF FITTINGS AND TUBING
STEP 1
Screw in the two G1/4 threaded male fittings. Attach the liquid
cooling tubes and connect the water-block(s) into the cooling circuit.
EKWB recommends using EK- fittings.
You can use any opening as an inlet/outlet port. Do not forget to plug
the remaining two opening with enclosed EK-Plug G1/4 or equivalent.
CAUTION: In case of using connectors other than EK- series
compression fittings, take special attention to the length of the
fittings’ male G1/4” thread. 5mm is the maximum allowed G1/4”
thread length!
STEP 1
Tubing
EK- Plug G1/4
EK-Fitting
CHECKING FOR CONTACTS
If necessary temporarily remove the water block to check for uniform
surface contact between the block and the components, pay special
attention to the VRM section of the graphics card. Check whether
the water block makes contact with the intended integrated circuit.
Then repeat sub-steps in previous section to re-attach the block.
In case you fail to obtain good contact, please check again that
your thermal pad thickness or contact our support service at
http://www.ekwb.com/support.

- 9 -
INSERTING THE CARD IN YOUR PC CASE
Carefully lift your graphics card with installed block and insert it in
your PC’s motherboard PCI express expansion slot. Please bear in
mind that your graphics card is probably heavier than when it was
equipped with original heat sink fan assembly. One needs to be
very careful when handling the graphics card. Avoid all un-needed
manipulation of the VGA/water block assembly that might damage
your card or water block during final installation.
Phillips-head screwdriver Scissors
REQUIRED TOOLS

For assistance please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA