ekwb EK-Pro GPU Quick Disconnect Kit User manual

INSTALLATION MANUAL
EK-Pro
GPU Quick Disconnect Kit
GPU WATER BLOCK

- 2 -
This product is compatible with all EK water blocks and manifolds. It is
intended for installation by expert users only. Please consult with
a qualified technician since improper installation may result in damage
to the equipment. EK assumes no liability whatsoever, expressed
or implied, for the use of these products, nor their installation. The
following instructions are subject to change without notice. Please visit
our website at www.ekwb.com for updates. Before the installation of
this product, please read important notice, disclosure, and warranty
conditions printed on the back of the box.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process and to prevent any possible damages to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw them
firmly in place since the liquid seal is ensured with the rubber
O-ring gaskets.
The use of quality market-proven corrosion-inhibiting coolants
is always strongly recommended for any liquid cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.

- 3 -
TABLE OF CONTENTS
PREPARING THE WATER BLOCK 4
REMOVING THE TERMINAL 4
MOUNTING THE NEW TERMINAL 4
MOUNTING THE BARB FITTINGS 5
MOUNTING THE ZMT TUBE 5
MEASURING TUBES 6
SUPPORT AND SERVICE 8
SOCIAL MEDIA 8

- 4 -
PREPARING THE WATER BLOCK
STEP 1
REMOVING THE TERMINAL
Remove all encircled screws using the 2.5mm Allen key and clean
the mounting surface of the water block with a nonabrasive cloth. EK
recommends you use a dry cloth only.
STEP 1
STEP 2
MOUNTING THE NEW TERMINAL
After you have cleaned the sealing surface, assemble the terminal,
as shown in the picture. Make sure that O-rings are correctly placed
into terminal channels. Once the terminal is in the right position on
the water block, insert and tighten the screws with a 2.5mm Allen key
and apply not more than 0.5 - 0.7 Nm of torque to avoid damaging
the water block. EK recommends this installation is done by
expert users only.
STEP 2
OR 15x1
EPDM50
M4x10 DIN7984
M4x28 DIN7984

- 5 -
STEP 3
MOUNTING THE BARB FITTINGS
Once the terminal is in the position and adequately screwed-in,
screw the barb fittings into the G1/4 threaded holes. For tightening,
use a fork wrench 18 with torque adjustment set to 0.8 Nm.
STEP 3
STEP 4
STEP 4
MOUNTING THE ZMT TUBE
For proper installation of ZMT tubes and clamps, EK recommends
the use of adequate hose clamp pliers.

- 6 -
STEP 5
MEASURING TUBES
When measuring the tube length, make sure to avoid any sharp
transitions of the tube to the barb fittings. Take a look at the
illustration for better understanding.
CORRECT
WRONG
Once the ZMT tubes and clamps are mounted, make sure they are
positioned correctly (as shown in the picture).
STEP 5

- 7 -
ADDITIONAL NECESSARY TOOLS
Hose Clamp Pliers
O-Ring OR 15x1
EPDM50 2 pcs
QD2-FS06-P -
Female QDC 2 pcs
TOP Acetal - FC
Terminal M4 Pre-
Filled1 pc
M4x10 DIN7984
Screw 2 pcs
M4x28 DIN7984
Screw 1pcs
BOX CONTENTS
Check the box contents carefully. The O-rings might already be installed
inside the terminal.
QD2-MSG4 - Male
QDC 2 pcs
2.5 mm Allen Key
1 pc
EK-HFB Fitting 6mm
2 pcs
Hose Clamp FSB
Mini 4 pcs
EK-Tube ZMT 6.5/9.5
Matte Black 1,2 m

In case you need assistance, please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA