ekwb EK-Quantum Momentum VRM Bridge ROG Maximus XII Formula D-RGB -... User manual

USER GUIDE
EKQuantum
Momentum VRM Bridge ROG Maximus XII Formula D-RGB - Plexi

This product is intended for installation only by expert users.
Please consult with a qualified technician for installation. Improper
installation may result in damage to your equipment. EK Water
Blocks assumes no liability whatsoever, expressed or implied,
for the use of these products, nor their installation. The following
instructions are subject to change without notice. Please visit our
web site at www.ekwb.com for updates. Before installation of this
product please read important notice, disclosure and warranty
conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
Please carefully read the manual thoroughly before beginning
with the installation process!
Please remove your motherboard from the computer to assure
safest mounting process in order to prevent any possible
damages to your CPU and/or motherboard’s circuit board (PCB).
The EK- Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber o-ring gaskets.
The use of quality, market proved corrosion inhibiting coolants
is always strongly recommended for any liquid cooling system.

- 3 -
STEP 2
Unscrew the M4 x 22 screw using the enclosed 2.5mm Allen key and
remove it from the block.
STEP 2
STEP 1
Install your EK-Quantum Velocity or Velocity Strike CPU water block in
the illustrated orientation and place the motherboard on a secure flat
surface. Using the enclosed 8mm Allen key, install all four (4) fixation
fittings to the pre-installed VRM block and CPU block.
Always consult the latest available manual for CPU block
installation. Do not use excessive force when tightening
the fittings.
STEP 1
Fixation Fitting
M4 x 22 Screw

- 4 -
STEP 4
Before attempting to mount the water block, apply a small amount
of the supplied grease to each of the four (4) O-Rings on the fixation
fittings. Next, position the water block over the fixation fittings and
force it into place evenly.
STEP 4
STEP 3
Slide the black acetal stand-out with stainless steel fixation plate away
from the plexi components until it stops (approximately at 3mm).
STEP 3
Black acetal
Stand-out
O-Ring
3 mm Gap

- 5 -
STEP 6
Install your fittings to the water block and pay attention that the
inlet port is now on the right-hand side (closest to the stand-out). EK
recommends the use of EK-Quantum Torque fittings.
STEP 6
STEP 5
Push the black acetal stand-out back to its original position and screw
back the M4 x 22 screw that was removed at Step 2.
If the water block does not fit or the stand-out will not
return to its original position, this could be due to the
misalignment of the CPU block. Loosen the four (4) thumb
nuts so that the CPU block is free to move and temporarily
position the bridge block. Lastly, re-tighten the four (4)
thumb nuts and start over from Step 4.
STEP 5
M4 x 22 Screw
Black acetal
Stand-out
Thumb Nut
INLET
EK-Fitting

- 6 -
STEP 7
Plug the 4-pin D-RGB connector from the bridge block in a D-RGB
header on your motherboard or controller. The LED strip will only
work if the pin layout on the header is as follows: +5V, Digital,
Empty, Ground.
Incorrect installation or installation to the incorrect header
could result in damage to the LED strip or the header itself.
D-RGB Header
RGB Header
STEP 7

For assistance please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA