ekwb EK-Thermosphere Guide

All disclosures, notices and warranty conditions are being written on EK Water Blocks website. Revision 1.1. Released on 9th of June, 2014.
Installation and mounting manual for EK-Thermosphere
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.
Before you start using this product please follow these basic guidelines:
1. Please carefully read the manual before through before beginning with the installation process!
2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).
3. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
4. The inhibiting use of corrosion coolants is always recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION ON PRODUCT COMPATIBILITY
STEP 2: TABLE OF CONTENT
Congratulations on your purchase of EK-Thermosphere. This item comes pre-
assembled and ready for use on GeForce GTX 600 and -700(Ti)/Titan series
graphics cards.
In order to install this product on graphics card other than mentioned above it is
mandatory to exchange the mounting plate for alternative one which needs to be
purchased separately!
The following items are enclosed with each EK-Thermosphere unit:
-EK-Thermosphere /w pre-installed G80 mounting plate and 2.5mm M3 standoffs
-Mounting screws:
oM3x4 DIN7985 screws
oM2.5x4 DIN7985 screws
oAdditional 3.9mm standoffs (M3 thread)
oAdditional 2.1mm standoffs (M2.5 thread)
-Required set of 2.0mm Allen key and EK-UNI standoff key
-TIM EK-Ectotherm (1g)
Alternative mounting plates available for
separate purchase through EK Webshop and
Partner Reseller Network:
EK-Thermosphere Mounting Plate G92: 53x53mm
(EAN: 3831109805299)
EK-Thermosphere Mounting Plate R600: 54x54mm
(EAN: 3831109805282)
EK-Thermosphere Mounting Plate GF560: 51x61mm
(EAN: 3831109805312)
EK-Thermosphere Mounting Plate G200: 61x61mm
(EAN: 3831109805305)
STEP 3: PREPARING THE GRAPHICS CARD
1. CLEANING THE CARD: Carefully detach the original stock cooler after removing all screws securing it to the board. Wipe off the remains (by using non–
abrasive cloth or qtip , as shown on sample photo) of the original thermal compound until the components and circuit board are completely clean. EKWB
recommends the use of denatured alcohol for removing TIM leftovers.
2. APPLYING THERMAL COMPOUND: Wipe off the remains (by using non–abrasive cloth or qtip ) of the original thermal compound until the components and
circuit board are completely clean. Apply thermal compound: lightly coat GPU chip with enclosed Gelid GC-Extreme thermal grease. EKWB recommends to apply
thermal grease in cross form for best performance (see sample picture).
STEP 4: ATTACHING WATERBLOCK
Carefully position the water block with preinstalled standoffs on to the graphics card. During this process please make sure you align mounting holes on the PCB with holes on the
water block (same applies for other tops). Also pay attention not to use too much force by pressing the block down to the PCB. Chip dies are prone to cracking.Use a Philips
screwdriver screw with the enclosed M3x4 DIN 7985 screws. EKWB recommends users to start tightening the screws in cross pattern.
M3x5 DIN7991 screw
GPU mounting plate with
standoff
Copper base
M3x4 (M2.5x4) DIN7985 screw
M3 plastic washer
Graphics card
EK-Thermosphere unit
CHECKING FOR PROPER CONTACT:
R emove the water block to check for uniform
surface contact between the water block and the
GPU. Then repeat sub-steps in previous section to
re-attach the block.
In case you fail to obtain good contact,
please check again that you are using
correct standoffs and/or contact our
support service at
http://www.ekwb.com/support.

All disclosures, notices and warranty conditions are being written on EK Water Blocks website. Revision 1.1. Released on 9th of June, 2014.
STEP 5: INSTALLING ALTERNATIVE GPU MOUNTING PLATE (OPTIONAL)
Prior to take the next steps it is mandatory to remove the four M3x4 DIN7991 screws holding the mounting plate attached to the copper base. Use enclosed Allen
key 2.0mm to remove the screws as shown in STEP 1.
After disassembling the mounting plate as shown on the STEP 1 please replace the metal hold-down plate with the plate of your choice.
OPTIONAL: Remove existing standoffs using enclosed EK-UNI standoff key to install alternative sized ones if necassery (example: in order to use this water block
with nVidia GeForce GTX 580 graphics card one must install 3.9mm M3-threaded standoffs (enclosed) onto the G80 Mounting plate).
Please follow the general fitting guideline below. For detailed compatibility list please visit http://www.coolingconfigurator.com !
G80 Mounting Plate:
- Used with 2.5mm standoffs (pre-installed):
for modern nVidia GeForce GTX 600 and -
GTX 700 family graphics cards (GK104,
GK110).
- Used with 3.9mm standoffs (optional):
for nVidia GeForce 8800 GTS/GTX (G80) and
GTX 465/470/480/560 448c/570/580
(GF100, GF110) family graphics cards
G92 Mounting Plate:
- Used with 2.5mm standoffs (pre-installed):
for nVidia GeForce 8800 GT(S) and 9800
GT(X) family graphics cards (G92).
for ATi/AMD Radeon HD 3800, 4870/4890,
5800, 6900 series graphics cards
- Used with 2.1mm standoffs (optional):
for nVidia GeForce GTS 450 / GTX 550/650
(Ti)
for Ati/AMD Radeon HD 4850, 6800, 7800
for modern AMD Radeon R9 270(X) series
graphics cards
G200 Mounting Plate:
- Used with 3.9mm M2.5 threaded standoffs:
for nVidia GeForce GTX 260/275/280/285
family graphics cards (G200, G200b)
GF560 Mounting Plate:
- Used with 3.9mm standoffs:
for nVidia GeForce GTX 460/560 (Ti) series
graphics cards
R600 Mounting Plate:
- Used with 2.5mm standoffs:
for ATi Radeon HD 2900 (R600) family cards
for AMD Radeon HD 7950/7970 series
graphics cards
for modern AMD Radeon R9 280(X)/290(X)
series graphics cards
Caution: GPU shim must be removed on some
R600 and 7950/7970 seris graphics cards.
Screw in the two G1/4 threaded male fittings. Attach the liquid cooling tubes and connect the water-block(s) into
the cooling circuit. EKWB recommends using EK-CSQ fittings with the EK-FC R9-290X series water
blocks. To ensure that the tubes are securely attached to the barb/fittings, please use hose clamps or an
appropriate substitute.
You can use any opening as an inlet/outlet port.
CAUTION: In case of using connectors other than EK-CSQ or EK-PSC series compression fittings, take special
attention to the length of the fittings’ male G1/4” thread. In case the thread is longer than 5 mm please use the
enclosed 1.8 mm nickel plated spacer!
5mm is the maximum allowed G1/4” thread length!
PLEASE NOTE THE PREFERED INLET PORT SIDE.
Tubing
EK-Plug G1/4
Acetal Terminal
EK-CSQ Fitting