Elation EPAR QA User manual

User Instructions
Rev. 10/12
EPAR QA
©Elation Professionals®
A Division of the AmericanDJ® Group of Companies
World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: [phone] Fax: [phone]
Web: www.elationlighting.com E-mail: [email protected]
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
[email protected] / www.americandj.eu
Tel: [phone] / Fax: [phone]

EPAR QA Introduction
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 2
Unpacking: Thank you for purchasing the EPAR QA by Elation Pro-
fessional®. Every EPAR QA has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your xture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing,
please contact our customer support number for further instructions.
Do not return this unit to your dealer without rst contacting customer
support.
Introduction: The EPAR QA is part of Elation Professionals®continu-
ing pursuit for creating high quality affordable intelligent fixtures. The
EPAR QA is a powerful DMX intelligent 4-in-1 RGBA (Red, Green, Blue,
& Amber) LED wash. This wash is light weight and compact which
makes it a great piece for mobile DJ’s and clubs. This unit can be used
as a stand alone, or a sound-active mode. The unit can also be con-
trolled via DMX controller.
Customer Support: ©Elation®provides a customer support line, to
provide set up help and to answer any question should you encounter
problems during your set up or initial operation. You may also visit us
on the web at www.elationlighting.com for any comments or sugges-
tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact
©Elation customer support.
PLEASE recycle the shipping carton when ever possible.
EPAR QA Specifications
Model: EPAR QA
SPECIFICATIONS:
Working Position: Any safe working position
Voltage: 100V ~ 240V/47~63Hz
LED’s: 14 x 1 Watt Quad LED’s (14 Red,
14 Blue, 14 Green, & 14 Amber)
Power Consumption: 78.4W
Fuse: 2.5 Amp
Beam Angle: 10 Degrees
Weight: 9lbs./ 4.1Kgs.
Dimensions: 9.9” (L) x 8.5” (W) x 11” (H)
Colors: RGBA Color Mixing
DMX Channels: 6 DMX Modes: 1 Channel Mode,
2 Channel Mode, 4 Channel Mode,
5 Channel Mode, 7 Channel Mode,
& 8 Channel Mode
Warranty: 2 Year (730 days)
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
Auto Sensing Voltage: This xture contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into
the power source.
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 19

Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 3
EPAR QA Warranty Registration
EPAR QA Features
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
EPAR QA General Instructions
• Multi-Colors
• Built in Microphone
• Four Operating Modes
• Five Dimming Curves
• DMX-512 protocol
• Six DMX Modes: 1 Channel Mode, 2 Channel Mode, 4 Channel
Mode, 5 Channel Mode, 7 Channel Mode, & 8 Channel Mode
• Dimming 0-100% in 2 Channel Mode, 5 Channel Mode, 7 Channel
Mode, & 8 Channel Mode.
• Daisy Chain Units Together in DMX Mode
The EPAR QA carries a two year limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All pack-
ages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 18
EPAR QA Warranty
2-YEAR LIMITED WARRANTY
A. Elation Professionals®hereby warrants, to the original purchaser, Elation Profes-
sionals®products to be free of manufacturing defects in material and workmanship
for a period of two years (730 days) from the date of purchase. This warranty shall be
valid only if the product is purchased within the United States of America, including
possessions and territories. It is the owner’s responsibility to establish the date and
place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the Elation Professionals®factory.
All shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, Elation Professionals®will
pay return shipping charges only to a designated point within the United States. If the
entire instrument is sent, it must be shipped in its original package. No accessories
should be shipped with the product. If any accessories are shipped with the product,
Elation Professionals®shall have no liability whatsoever for loss of or damage to any
such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the prod-
uct is modied in any manner which Elation Professionals®concludes, after inspec-
tion, affects the reliability of the product; if the product has been repaired or serviced
by anyone other than the Elation Professionals®factory unless prior written authori-
zation was issued to purchaser by Elation Professionals®; if the product is damaged
because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance,
cleaning or periodic check-up. During the period specied above, Elation Profession-
als®will replace defective parts at its expense, and will absorb all expenses for war-
ranty service and repair labor by reason of defects in material or workmanship. The
sole responsibility of Elation Professionals®under this warranty shall be limited to the
repair of the product, or replacement thereof, including parts, at the sole discretion
of Elation Professionals®. All products covered by this warranty were manufactured
after January 1, 1990, and bear identifying marks to that effect.
E. Elation Professionals®reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes in
any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited
by applicable law, all implied warranties made by Elation Professionals®in connec-
tion with this product, including warranties of merchantability or tness, are limited in
duration to the warranty period set forth above. And no warranties, whether expressed
or implied, including warranties of merchantability or tness, shall apply to this prod-
uct after said period has expired. The consumer’s and or Dealer’s sole remedy shall
be such repair or replacement as is expressly provided above; and under no circum-
stances shall Elation Professionals®be liable for any loss or damage, direct or conse-
quential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to Elation Professionals®
Products and supersedes all prior warranties and written descriptions of warranty
terms and conditions heretofore published.

EPAR QA Safety Precautions
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 4
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 17 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu-
ding amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
EPAR QA Cleaning
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
EPAR QA Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 17

Power Supply: The Elation EPAR QA contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into the
power source. With this switch there is no need to worry about the cor-
rect power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli-
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The EPAR QA has 6 DMX Channel Modes. The DMX address is set
electronically using the controls on the rear panel of the unit. Your unit
and your DMX controller require a approved DMX-512 110 Ohm Data
cable for data input and data output. We recommend Accu-Cable DMX
cables. If you are making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end of
the cable. Also remember that DMX cable must be
daisy chained and cannot be split.
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 5
EPAR QA Set Up
Figure 1
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 16
EPAR QA Photometric Chart
EPAR QA
Photometric Beam Angle Data
Standard 10° Beam Angle
LUX x0.0929 = FC
R
G
B
A
ALL
267 FC / 2871 LUX
351 FC / 3774 LUX
42 FC / 450 LUX
165 FC / 1774 LUX
727 FC / 7830 LUX
64 FC / 691 LUX
94 FC / 1011 LUX
13 FC / 137 LUX
51 FC / 553 LUX
191 FC / 2060 LUX
33 FC / 350 LUX
40 FC / 428 LUX
6 FC / 62 LUX
24 FC / 259 LUX
91 FC / 981 LUX
10° Beam Angle
0 m
0 ft 1 m
3.28 ft
3 m
9.84 ft
2 m
6.56 ft
Ø 0.24 m / Ø 0.79 ft Ø 0.48 m / Ø 1.57 ft Ø 0.72 m / Ø 2.36 ft
Beam Diameter
10° Beam Angle
EPAR QA Dimmer Curve Diagram
Unit Dim Mode (Fade Time) (Fade Time)
Ramp Effect
Standard
Stage
TV
Architectural
Theatre

Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 6
EPAR QA Set Up
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting
standard 5-pin data cables in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 15
EPAR QA Color Macro Chart
R G B A R G B A
0000kcalb
33orcam08432552081orcam 255 206 143 0
43orcam08461552082orcam 254 177 153 0
53orcam77211552773orcam 254 192 138 0
63orcam38385527114orcam 254 165 98 0
73orcam77775520615orcam 254 121 0 0
83orcam38385523226orcam 176 17 0 0
93orcam77773425527orcam 96 0 11 0
04orcam47470025528orcam 234 139 171 0
14orcam77776615529orcam 224 5 97 0
24orcam474752155201orcam 175 77 173 0
34orcam47777955211orcam 119 130 199 0
44orcam17771755221orcam 147 164 212 0
54orcam384313855231orcam 88 2 163 0
64orcam392813955241orcam 0 38 86 0
74orcam696326955251orcam 0 142 208 0
84orcam395523983261orcam 52 148 209 0
94orcam785527869171orcam 1 134 201 0
05orcam095520905181orcam 01452120
15orcam775527700191orcam 01211920
25orcam775520017702orcam 01291840
35orcam765528417612orcam 0 83 115 0
45orcam785525917722orcam 0 97 1660
55orcam775524327732orcam 11001670
65orcam44144155285142orcam 0 40 86 0
75orcam35135115255252orcam 2092191820
85orcam74174157155262orcam 42 165 85 0
95orcam83168183155272orcam 0 46 35 0
06orcam74115274155282orcam 81072220
16orcam83155283115192orcam 1071562310
26orcam74155274115103orcam 1651982470
36orcam83155296183113orcam 0 0 1890
055255255246orcam55255255255223orcam

LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE
button until ds-X is displayed, “X” representing either 1 or 2. Press
the UP or DOWN button so that ds-2 is displayed, now the display
will turn off after 10secs. Press any button for at least 5secs. to turn
the display on again. Be advised though that the display will turn off
automatically after 10 seconds of inactivity.
ds-1= LCD display on at all times.
ds-2= LCD display shuts off after 10 seconds.
Operating Modes:
You can use the EPAR QA in four ways:
• Macro Mode - There are 64 color macros to choose from.
• Auto Mode - There are 9 built in programs to choose from.
• RGBA mode - Control the intensity of all four colors adjusting the
intensity to your desire.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the Elation® Show Designer™.
Macro Mode:
1. Plug the fixture in and press the MODE button until “C-XX” is dis-
played. “XX” representing a number between 0-64.
2. There are 64 macros to choose from. Select your desired macro by
pressing the UP and DOWN buttons.
Program Mode:
1. Plug the fixture in and press the MODE button until “A-XX” is dis-
played. “XX” representing a number between 1-09 or AL.
2. There are 9 built-in programs to choose from or you can select
“A-AL” and run all 9 programs. Select your desired program by
pressing the UP and DOWN buttons. You can set your program
speed by following the next set of instructions.
Program Mode Speed Adjustment:
1. To adjust the speed of your program press the MODE button until
“P-XX” is displayed.
2. Press the UP or DOWN buttons to make the adjustmetns. “P-01” is
the slowest speed, “P-16” the fastest speed. When the display
reads “P-So” the Auto mode is running by sound activity.
EPAR QA Operating Instructions
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 7
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 14
Channel 1, 2, 3, & 4 will not work, when Channel 5 is being
used.
When using Channel 7, Channel 6 will control the speed of the
color changing.
EPAR QA 8 Channel Mode - DMX Values and Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 1 - 255 COLOR MACROS
PLEASE SEE 1 CHANNEL MODE
6 STROBING/PROGRAM SPEED
0 - 15 NOTHING
16 - 255 STROBING
SLOW - FAST
1 - 255 PROGRAM SPEED SLOW - FAST
7 MODE
0 - 127 OFF
128 - 159 AUTO MIX
160 - 191 3 COLOR JUMP
192 - 223 7 COLOR JUMP
224 - 255 SOUND ACTIVE
8 MASTER DIMMER
0 - 255 0% - 100%

Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 8
RGB Mode:
1. Plug the fixture in and press the MODE button until:
2. When rXXX is displayed you are in Red dimming mode. Press the
UP and DOWN buttons to adjust intensity.
3. When GXXX is displayed you are in Green dimming mode. Press the
UP and DOWN buttons to adjust intensity.
4. When bXXX is displayed you are in Blue dimming mode. Press the
UP and DOWN buttons to adjust intensity.
5. When AXXX is displayed you are in amber dimming mode. Press the
UP and DOWN buttons to adjust intensity.
6. You can use the color macro chart on page 15 to create one of the 64
macros.
DMX Mode:
Operating through a DMX controller givesthe user the freedom to create
their own programs tailored to their own individual needs. The EPAR QA
has 6 DMX modes: 1 Channel mode, 2 Channel mode, 4 Channel mode,
5 Channel mode, 7 Channel mode, and a 8 Channel mode. See pages
10-14 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s traits
with a standard DMX 512 controller such as the Elation® Show
Designer™ or the Elation® DMX Operator™.
2. To run your fixture in DMX mode, plug in the fixture via the XLR con-
nections to any standard DMX controller. Select your desired DMX
mode, and then press the UP or DOWN buttons to adjust the DMX
address. XXX = DMX Address
3. To run the 1 Channel Mode, press the MODE button until “1XXX”
is displayed. This is the DMX addressing for the 1 Channel Mode.
4. To run the 2 Channel Mode, press the MODE button until “2XXX”
is displayed. This is the DMX addressing for the 2 Channel Mode.
5. To run the 4 Channel Mode, press the MODE button until “3XXX”
is displayed. This is the DMX addressing for the 4 Channel Mode.
6. To run the 5 Channel Mode, press the MODE button until “4XXX”
is displayed. This is the DMX addressing for the 5 Channel Mode.
7. To run the 7 Channel Mode, press the MODE button until “5XXX”
is displayed. This is the DMX addressing for the 7 Channel Mode.
8. To run the 8 Channel Mode, press the MODE button until “6XXX”
is displayed. This is the DMX addressing for the 8 Channel Mode.
9. Please see pages 10-14 for DMX values and traits.
EPAR QA Operating Instructions EPAR QA 7 Channel Mode - DMX Values and Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 1 - 255 COLOR MACROS
PLEASE SEE 1 CHANNEL MODE
6 0 - 15 NOTHING
16 - 255 STROBING/SPEED CONTROL
7 MASTER DIMMER
0 - 255 0% - 100%
Channel 1, 2, 3, & 4 will not work, when Channel 5 is being
used.
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 13

Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 9
Master-Slave Operation:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be pro-
grammed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR data cables to link your units together. Remem-
ber that the Male XLR connector is the input and the Female XLR
connector is the ouput. The first unit in the chain (master) will use
the female XLR connector only. The last unit in the chain will use the
male XLR connector only.
2. Set the “Master” unit to your desired mode or operation.
3. For the “Slave” unit(s), set the display to any DMX channel mode.
Example: Set the unit to 4 channel mode, the display should read
“3000” or any variables, i.e “3001”, “3002 etc..
4. Connect the “Slave” unit or units and they will automatically start to
follow the “Master.”
EPAR QA Master-Slave Configuration
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
5 MASTER DIMMER
0 - 255 0% - 100%
EPAR QA 5 Channel Mode - DMX Values and Functions
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 12
EPAR QA 2 Channel Mode - DMX Values and Functions
Channel Value Function
1 1 - 255 COLOR MACROS
PLEASE SEE 1 CHANNEL MODE
2 0 - 255 MASTER DIMMER 0% - 100%
EPAR QA 4 Channel Mode - DMX Values and Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 AMBER
0 - 255 0% - 100%
Dimmer Curve Setting:
1. Plug the fixture in and press the MODE button until “dr-X” is dis-
played. “X” representing a number between 0-4.
2. There are 5 dimmer curve settings to choose from. Please see the
Dimmer Curve Diagram Chart on page 16 to see the settings and
their respective beginning and ending fade times.
EPAR QA Operating Instructions

Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 11
EPAR QA 1 Channel Mode - DMX Values and Functions
Channel Value Function
1 COLOR MACROS CONT.
129 - 132 MACRO 33
133 - 136 MACRO 34
137 - 140 MACRO 35
141 - 144 MACRO 36
145 - 148 MACRO 37
149 - 152 MACRO 38
153 - 156 MACRO 39
157 - 160 MACRO 40
161 - 164 MACRO 41
165 - 168 MACRO 42
169 - 172 MACRO 43
173 - 176 MACRO 44
177 - 180 MACRO 45
181 - 184 MACRO 46
185 - 188 MACRO 47
189 - 192 MACRO 48
193 - 196 MACRO 49
197 - 200 MACRO 50
201 - 204 MACRO 51
205 - 208 MACRO 52
209 - 212 MACRO 53
213 - 216 MACRO 54
217 - 220 MACRO 55
221 - 224 MACRO 56
225 - 228 MACRO 57
229 - 232 MACRO 58
233 - 236 MACRO 59
237 - 240 MACRO 60
241 - 244 MACRO 61
245 - 248 MACRO 62
249 - 252 MACRO 63
253 - 255 MACRO 64
Elation Professional - www.elationlighting.com - EPAR QA Instruction Manual Page 10
EPAR QA 1 Channel Mode - DMX Values and Functions
Channel Value Function
1 COLOR MACROS
0 OFF
1 - 4 MACRO 1
5 - 8 MACRO 2
9 - 12 MACRO 3
13 - 16 MACRO 4
17 - 20 MACRO 5
21 - 24 MACRO 6
25 - 28 MACRO 7
29 - 32 MACRO 8
33 - 36 MACRO 9
37 - 40 MACRO 10
41 - 44 MACRO 11
45 - 48 MACRO 12
49 - 52 MACRO 13
53 - 56 MACRO 14
57 - 60 MACRO 15
61 - 64 MACRO 16
65 - 68 MACRO 17
69 - 72 MACRO 18
73 - 76 MACRO 19
77 - 80 MACRO 20
81 - 84 MACRO 21
85 - 88 MACRO 22
89 - 92 MACRO 23
93 - 96 MACRO 24
97 - 100 MACRO 25
101 - 104 MACRO 26
105 - 108 MACRO 27
109 - 112 MACRO 28
113 - 116 MACRO 29
117 - 120 MACRO 30
121 - 124 MACRO 31
125 - 128 MACRO 32