ElectrIQ ECOSILENT12HPW User manual

USER MANUAL
ECOSILENT12HPW
electriQ 12,000 BTU PORTABLE AIR CONDITIONER
WITH HEAT PUMP AND WIFI
Thank you for choosing electriQ
Please read this user manual before using this innovative Air Conditioner and keep it
safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

CONTENTS
SAFETY
FEATURES AND PARTS LIST
INSTALL ATION
OPER ATION
SMART INDICATOR
2
4
5
7
8
REMOTE CONTROL 8
WIFI APP CONTROL
CLEANING AND MAINTENANCE
TROUBLESHOOTING
ERROR CODES
SUPPORT
TECHNICAL SPECIFICATION
10
20
21
21
22
23
SETTING UP THE APP 10
CONNECTING THE AIR CONDITIONER 13
CONTROLLING YOUR DEVICE 15
SMART SCENES 17
EMPTYING THE INTERNAL WATER TANK 9
1

SAFETY INSTRUCTIONS
Important!
• Carefully read the instructions before operating the unit
• This appliance is for indoor use only.
• Rating: This unit must be only connected to a 220-240 V / 50 Hz
earthed outlet.
• Installation must be in accordance with regulations of the country where the unit is used.
• If you are in any doubt about the suitability of your electrical supply have it checked and,
if necessary, modied by a qualied electrician.
• This air conditioner has been tested and is safe to use. However, as with any electrical
appliance - use it with care.
• Disconnect the power from the appliance before dismantling, assembling or cleaning.
• Avoid touching any moving parts of the appliance.
• Never insert ngers, pencils or any other objects though the guard
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities. It is also not intended for use by those with a
lack of experience and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety.
• Do not leave children unsupervised with this appliance.
• Do not clean the unit by spraying it or immersing it in water.
• Never connect the unit to an electrical outlet using an extension cord. If an outlet is not
available, one should be installed by a qualied electrician.
• Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not
stretched or exposed to sharp objects/edges.
• A damaged supply cord should be replaced by the manufacturer or a qualied electrician
in order to avoid a hazard.
• Any service other than regular cleaning or lter replacement should be performed by an
authorised service representative. Failure to comply could result in a voided warranty.
• Do not use the appliance for any purpose other than its intended use.
• The air conditioner unit must always be stored and transported upright, otherwise
irreparable damage may be caused to the compressor; if in doubt we suggest waiting at
least 24 hours before starting the unit.
• Avoid restarting the air conditioning unit unless 3 minutes have passed since being
turned off. This prevents damage to the compressor.
• Never use the mains plug as a switch to start and turn off the air conditioning unit. Use
the provided ON/OFF button located on the control panel.
• Always place the unit on a dry and stable surface.
• The appliance should not be installed in laundry or wet rooms.
• The appliance must be placed in a room without sources of ignition (for example: open
ames, an operating gas appliance or an operating electric heater).
2

• R290 refrigerant gas complies with European environmental directives.
• R290 has a low GWP (Global Warming Potential) of 3.
• The air conditioner contains about 300 g of R290 refrigerant gas.
• Do not use or store in an unventilated space with an area smaller than 14.4 m2per unit.
• The room must be such as to prevent stagnation of possible leaks of refrigerant gas as
there could be a danger of re or explosion should the refrigerant come into contact with
electric heaters, stoves or other sources of ignition.
• Refrigerant gas may be odourless.
• Do not use the product and contact the retailer for advice, if damage has occurred to the
unit which may have compromised the refrigerant system.
• Any repairs or maintenance must only be carried out on the unit by a suitably qualied
engineer. Before opening and servicing the unit the authorised engineer must be in
possession of a copy of the manufacturer’s service manual and must follow the safety
information contained within it to ensure all hazards are minimized.
• The refrigerant system should not be perforated or punctured.
Energy Saving and Unit Safety Protection Tips
• Do not cover or restrict the airow from the outlet or inlet grills.
• For maximum performance the minimum distance from a wall or objects should be
50cm.
• Keep the lters clean. Under normal conditions, lters should only need cleaning once
every three weeks (approximately). Since the lters remove airborne particles, more
frequent cleaning maybe necessary, depending on the air quality.
• For the initial start-up set the fan speed to maximum and the thermostat to 5 degrees
lower than the current temperature. After, set the fan switch to low and set the
thermostat to your desired setting.
• To protect the unit, we recommend not using the cooling function when the ambient
temperature is higher than 35oC.
3

FEATURES AND PARTS LIST
• 4 in 1 Cooling, Heating, Fan and Dehumidier great for Rooms up to 20 sqm.
• 5 speed DC fan: balancing quiet operation with performance.
• SmartCool Logic for Improved Energy Efciency.
• HEPA Filter for Air Purication
• 24 Hours Start / Stop Timer
• Digital Thermostat.
• Auto-Restart to retain the settings in the event of power failure.
• WIFI control from app
• Castors and Handles for Enhanced Portability
Control Panel
Louvre
(Air Outlet)
Rear Housing
Front Housing
Castors
Smart
Indicator
Plug
Upper
Air Inlet
Carry hand
Lower
Air Inlet
Exhaust
Outlet
Exhaust House Window Side Bar
4

INSTALLATION
INSTALLATION OF WINDOW KIT
WARNING: Before using this unit, please keep it upright for at least 3-4 hours.
This unit can easily be moved from one room to another. While moving the unit please note that it must
always be kept upright and then placed on an even surface.
1. Attach the shtail connector to the end of the hose, by
extending the end and twisting until rmly attached (At least
3 full rotations).
2. Attach the connector on the opposite end of the pipe to the exhaust outlet
on the rear of the appliance by putting into position and twisting to lock in
place.
The window kit (slide bar and shtail) can be used with sliding windows and doors. For other types of window, the
shtail should be used on its own.
2. Fix the shtail adaptor into the
opening on the slide bar
3. Fix the exhaust connector on
the opposite end of the exhaust
hose to the exhaust outlet on
the rear of the air conditioner.
1. Partially open the window and place the
extended slide bar in position before closing
the window onto it.
3. Make sure the unit is upright and there are no obstructions to the air
inlets and outlet grills.
50CM
50CM
5

INSTALLING THE HEPA FILTER (OPTIONAL)
The air conditioner can accommodate a HEPA lter which will purify the
air expelled back into the room in any operating mode. These can be
purchased from the stockist using the code: FIL-ECOSILENTHEPA.
The HEPA lter should be unwrapped and installed in the upper air inlet.
To install, remove the upper lter frame from the air conditioner by
pressing the two clips on the top of the lter frame. Place the HEPA lter
within the lter frame before retting onto the unit.
In order to maintain performance, the lter should be regularly
vacuumed. The lter should be replaced every six months, depending on
usage and air quality.
NOTES:
• The window kit is only designed to be installed with sliding or sash windows or doors. The window
kit is not designed or to be used with any other style of windows.
• The sh tail adaptor can be used without the slide bar with most windows / doors.
• When using the air conditioner ensure that the opening left around the shtail is as small as possible as
the cooling will be less efcient.
• The best form of installation is through a wall duct. By properly venting you expel hot air from your
room while efciently cooling it.
• Your air conditioner should be used without the vent pipe in dry mode. When using dry mode
ensure that an external water tank is used, monitored and regularly emptied before overowing.
Permanent plumbing can be also installed for dry mode or an external uplift water pump can be
set up for unattended use.
IMPORTANT SAFEGUARDS
The length of the soft hose extends from approximately 35 cm to 200 cm. If hose is extended above this
length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well ventilated
and not obstructed as this will cause the unit to overheat. Keep the hose as straight and short as possible
and avoid bending the air hose by more than 30 degrees in order not to reduce the performance of the
unit.
6

OPERATION
Press the POWER button to turn the unit ON or OFF.
Press the MODE button to cycle between the 5 modes, the indicator for the selected mode will be
illuminated.
COOL: The room is cooled with the cold air expelled through the front air outlet while hot air is expelled
through the vent pipe. The desired room temperature can be set between 17 and 30 degrees using the +
and – buttons, and the fan speed can be changed using the SPEED button.
HEAT: The room is heated with the warm air expelled through the front air outlet while cold air is expelled
through the vent pipe. The desired room temperature can be set between 16 and 32 degrees using the + and
– buttons, and the fan speed can be changed using the SPEED button. We advise for continuous drainage to
be set up in HEAT mode.
FAN (AIR PURIFIER): The fan speed can be changed pressing the SPEED button. When used with the
optional HEPA lter, the appliance will work as an effective air purier.
DRY (DEHUMIDIFY): Should be operated without the vent hose, but with continuous drainage to remove
moisture from the air. The display will show dH while in dry mode. The fan speed is set to low and is not
adjustable.
SMART COOL: An intelligent cooling mode where the fan speed is automatically adjusted based on the
amount of cooling required. Attempts to change the fan speed will move the unit into COOL mode.
Repeatedly press the SPEED button to cycle through the ve fan speeds. Each time the SPEED button is
pressed, the fan speed will be displayed. The fan speed can be changed between F1 (Low) to F5 (High). The
LED indicators will also illuminate to show the fan speed as below:
F1 –Low, F2 – Low and Mid, F3 – Mid, F4 – Mid and High, F5 – High.
The fan speed cannot be changed in SMARTCOOL and DRY modes.
Press to enter sleep mode. The sleep indicator will be illumined and all other indicators will be turned
off. In sleep mode, the appliance works at low fan speed. Press SLEEP again to exit sleep mode.
Alternatively press and hold the sleep button for 3 seconds, and the unit will operate with the existing
settings, but with the lights turned off.
The timer functions cannot be combined or repeated.
POWER ON TIMER
With the appliance in standby, press the TIMER button to set the power-on timer. Use the + and -
buttons to adjust the duration of the timer (1 to 24 hours). The Timer indicator will turn on and the
unit will start after the selected number of hours.
POWER OFF TIMER
With the appliance running with the desired settings, press the TIMER button to set the power-off
timer. Use the + and - buttons to adjust the duration of the timer (1 to 24 hours). The timer indicator
will illuminate and the unit will stop after selected number of hours.
Used to adjust temperature in HEAT/COOL/SMART COOL modes and to set the duration of the
TIMER. The buttons are not used in FAN or DRY modes. Press both buttons together to change
between displaying the temperature in Celsius and Fahrenheit.
Press this button to enable the swing function. The louvres will slowly move from side to side. If swing
is pressed again the louvres will stop in their current position.
7

REMOTE CONTROL
POWER Press to turn the unit on or off.
TIMER Press to set the timer.
DOWN Press to decrease the desired temperature or
timer duration.
UP Press to increase the desired temperature or
timer duration.
SLEEP Press the sleep button to enter sleep mode.
SWING Press swing to turn the swing function on or off.
oC/oFPress to change between displaying the
temperature in Celsius or Fahrenheit.
FAN Press to enter fan / air purify mode.
COOL Press to enter cool mode.
HEAT Press to enter heat mode.
DRY Press to enter dry (dehumidify) mode.
HIGH Press to enter high (F5) speed fan.
MID Press to enter medium (F3) speed fan.
LOW Press to enter low (F1) speed fan.
NOTE: The design of the remote may vary from the diagram, due to
continuous product improvement.
SMART INDICATOR LED
The air conditioner contains a Smart Indicator which changes colour to show from a distance what mode the
air conditioner is set to.
HEAT MODE
The indicator will display Red.
COOL MODE
The indicator will display Blue.
SMART COOL MODE
The indicator will display Blue.
FAN (AIR PURIFIER) MODE
The indicator will display Green.
DRY (DEHUMIDIFY) MODE
The indicator will display Orange.
Smart Indicator
8