ElectrIQ ECOSILENT10HPW User manual

USER MANUAL
electriQ 10,000 BTU PORTABLE AIR CONDITIONER
WITH HEAT PUMP AND WIFI
ECOSILENT10HPW
Thank you for choosing electriQ
Please read this user manual before using this innovative Air Conditioner and keep it
safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

1

2
CONTENTS
SAFETY
3
FEATURES AND PARTS LIST
5
INSTALLATION
6
OPERATION
9
REMOTE CONTROL
10
EMPTYING THE INTERNAL WATER TANK
11
WIFI APP CONTROL
12
SETTING UP THE APP
12
CONNECTING THE AIR CONDITIONER
15
CONTROLLING YOUR DEVICE
17
SMART SCENES
20
CLEANING AND MAINTENANCE
23
TROUBLESHOOTING
24
ERROR CODES
24
SUPPORT
25
TECHNICAL SPECIFICATION
26

3
SAFETY INSTRUCTIONS
Important!
•Carefully read the instructions before operating the unit
•This appliance is for indoor use only.
•Rating: This unit must be only connected to a 220-240 V / 50 Hz
earthed outlet.
•Installation must be in accordance with regulations of the country where the unit is used.
•If you are in any doubt about the suitability of your electrical supply have it checked and,
if necessary, modified by a qualified electrician.
•This air conditioner has been tested and is safe to use. However, as with any electrical
appliance - use it with care.
•Disconnect the power from the appliance before dismantling, assembling or cleaning.
•Avoid touching any moving parts of the appliance.
•Never insert fingers, pencils or any other objects though the guard
•This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities. It is also not intended for use by those with a
lack of experience and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety.
•Do not leave children unsupervised with this appliance.
•Do not clean the unit by spraying it or immersing it in water.
•Never connect the unit to an electrical outlet using an extension cord. If an outlet is not
available, one should be installed by a qualified electrician.
•Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not
stretched or exposed to sharp objects/edges.
•A damaged supply cord should be replaced by the manufacturer or a qualified electrician
in order to avoid a hazard.
•Any service other than regular cleaning or filter replacement should be performed by an
authorised service representative. Failure to comply could result in a voided warranty.
•Do not use the appliance for any purpose other than its intended use.
•The air conditioner unit must always be stored and transported upright, otherwise
irreparable damage may be caused to the compressor; if in doubt we suggest waiting at
least 24 hours before starting the unit.
•Avoid restarting the air conditioning unit unless 3 minutes have passed since being
turned off. This prevents damage to the compressor.
•Never use the mains plug as a switch to start and turn off the air conditioning unit. Use
the provided ON/OFF button located on the control panel.
•Always place the unit on a dry and stable surface.
•The appliance should not be installed in laundry or wet rooms.
•The appliance must be placed in a room without sources of ignition (for example: open
flames, an operating gas appliance or an operating electric heater).

4
•R290 refrigerant gas complies with European environmental directives.
•R290 has a low GWP (Global Warming Potential) of 3.
•The air conditioner contains about 200g of R290 refrigerant gas.
•Do not use or store in an unventilated space with an area smaller than 9.6 m2per unit.
•The room must be such as to prevent stagnation of possible leaks of refrigerant gas as
there could be a danger of fire or explosion should the refrigerant come into contact with
electric heaters, stoves or other sources of ignition.
•Refrigerant gas may be odourless.
•Do not use the product and contact the retailer for advice, if damage has occurred to the
unit which may have compromised the refrigerant system.
•Any repairs or maintenance must only be carried out on the unit by a suitably qualified
engineer. Before opening and servicing the unit the authorised engineer must be in
possession of a copy of the manufacturer’s service manual and must follow the safety
information contained within it to ensure all hazards are minimized.
•The refrigerant system should not be perforated or punctured.
Energy Saving and Unit Safety Protection Tips
•Do not cover or restrict the airflow from the outlet or inlet grills.
•For maximum performance the minimum distance from a wall or objects should be
50cm.
•Keep the filters clean. Under normal conditions, filters should only need cleaning once
every three weeks (approximately). Since the filters remove airborne particles, more
frequent cleaning maybe necessary, depending on the air quality.
•For the initial start-up set the fan speed to maximum and the thermostat to 5 degrees
lower than the current temperature. After, set the fan switch to low and set the
thermostat to your desired setting.
•To protect the unit, we recommend not using the cooling function when the ambient
temperature is higher than 35oC.

5
FEATURES AND PARTS LIST
•4 in 1 Cooling, Heating, Fan and Dehumidifier.
•5 speed DC fan: balancing quiet operation with performance.
•SmartCool Logic for Improved Energy Efficiency.
•HEPA Filter for Air Purification
•24 Hours Start / Stop Timer
•Digital Thermostat.
•Auto-Restart to retain the settings in the event of power failure.
•WIFI control from app
•Castors and Handles for Enhanced Portability

6
INSTALLATION
WARNING: Before using this unit, please keep it upright for at least 3-4 hours.
This unit can easily be moved from one room to another.
While moving the unit please note that it must always be kept upright and then placed on an even surface.
1. Attach the fishtail connector to the end of the
hose, by extending the end of the hose and
twisting until firmly attached to the connector
(At least 3 full rotations).
2. Attach the Hose to the Outlet adaptor, in the
same way by extending the end of the hose
and twisting until firmly attached (At least 3 full
rotations).
3. Slide the Outlet adaptor into position on the
rear of the unit. The two slips on the unit will
hold it in place. (To remove the adaptor
press the two clips down to release it from
the unit)
4.Make sure the unit is upright and there are no
obstructions to the air inlets and outlet grills, with at
least 50cm of space to the sides and rear of the unit.

7
INSTALLATION OF WINDOW KIT
The window kit (slide bar and fishtail) can be used
with sliding windows and doors. For other types of
window, the fishtail should be used on its own.
NOTES:
•The window kit is only designed to be installed with sliding or sash windows or doors. The window kit
is not designed to be used with any other style of windows.
•The fish tail adaptor can be used without the slide bar with most windows / doors.
•When using the air conditioner ensure that the opening around the fishtail adaptor is as small as
possible to ensure the efficiency of the unit is not reduced.
•The best form of installation is through a wall duct. By properly venting you expel hot air from your
room while efficiently cooling it.
•Your air conditioner should be used without the vent pipe in dry mode. When using dry mode ensure
that an external water tank is used, monitored and regularly emptied before overflowing. Permanent
plumbing can be also installed or an external uplift water pump can be set up to allow for
uninterrupted use.
3. Push the screw thread of the plate through
the hole in the rear of the front slide bar
section.
2. Slide the rear section of the slide bar onto the
front section lining up the plate so it runs
within the groove. Extend the bar to the
required length, and use the supplied wing nut
to secure
4. Partially open the
window and place the
extended slide bar in
position before closing
the window onto it.
5. Fix the fishtail adaptor
into the opening on
the slide bar.
Plate
Wing nut
Slide Bar
(Front Section)
Slide Bar
(Rear Section)

8
INSTALLING THE HEPA FILTER (OPTIONAL)
The air conditioner can accommodate a HEPA filter which will purify the
air expelled back into the room in any operating mode. These can be
purchased from the stockist using the code: FIL-ECOSILENTHEPA.
The HEPA filter should be unwrapped and installed in the upper air inlet.
To install, remove the upper filter frame from the air conditioner by
pressing the two clips on the top of the filter frame. Place the HEPA filter
within the filter frame before refitting onto the unit.
In order to maintain performance, the filter should be regularly
vacuumed. The filter should be replaced every six months, depending on
usage and air quality.
NOTES:
•The window kit is only designed to be installed with sliding or sash windows or doors. The window
kit is not designed or to be used with any other style of windows.
•The fish tail adaptor can be used without the slide bar with most windows / doors.
•When using the air conditioner ensure that the opening left around the fishtail is as small as
possible to ensure the unit performs efficiently.
•The best form of installation is through a wall duct. By properly venting you expel hot air from your
room while efficiently cooling it.
•Your air conditioner should be used without the vent pipe in dry mode. When using dry mode
ensure that an external water tank is used, monitored and regularly emptied before overflowing.
Permanent plumbing can be also installed for dry mode or an external uplift water pump can be
set up for unattended use.
IMPORTANT SAFEGUARDS
The length of the soft hose extends from approximately 35 cm to 180 cm. If hose is extended above this
length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well ventilated
and not obstructed as this will cause the unit to overheat. Keep the hose as straight and short as possible
and avoid bending the air hose by more than 30 degrees in order not to reduce the performance of the
unit.

9
OPERATION
Press the POWER button to turn the unit ON or OFF.
Press the MODE button to cycle between the 5 modes, the indicator for the selected mode will be
illuminated.
COOL: The room is cooled with the cold air expelled through the front air outlet while hot air is
expelled through the vent pipe. The desired room temperature can be set between 17 and 30 degrees
using the + and –buttons, and the fan speed can be changed using the SPEED button.
HEAT: The room is heated with the warm air expelled through the front air outlet while cold air is
expelled through the vent pipe. The desired room temperature can be set between 17 and 30 degrees
using the + and –buttons, and the fan speed can be changed using the SPEED button. We advise for
continuous drainage to be set up in HEAT mode.
FAN (AIR PURIFIER): The fan speed can be changed pressing the SPEED button. When used with the
optional HEPA filter, the appliance will work as an effective air purifier.
DRY (DEHUMIDIFY): Should be operated without the vent hose, but with continuous drainage to
remove moisture from the air. The display will show dH while in dry mode. The fan speed is set to low
and is not adjustable.
AUTO: The unit will automatically change between modes, depending on the room temperature and
desired temperature set.
Repeatedly press the SPEED button to cycle through the five fan speeds. Each time the SPEED button
is pressed, the fan speed will be displayed. The fan speed can be changed between F1 (Low) to F5
(High). The LED indicators will also illuminate to show the fan speed as below:
F1 –Low, F2 –Low and Mid, F3 –Mid, F4 –Mid and High, F5 –High.
Press to enter sleep mode. The sleep indicator will be illumined and all other indicators will be turned
off. In sleep mode, the appliance works at low fan speed. Press SLEEP again to exit sleep mode.
Press and hold the SLEEP button while the unit is in standby to activate the WiFi connection mode.